EF Logo

Volvo/Mack · MID 130 transmission ECU

Volvo/Mack Clutch operation fault codes

The transmission ECU monitors that the clutch engages and disengages as commanded. These codes cover drag, slip and unintended movement.

FaultCheckMID 130PSID 27FMI 12Volvo/Mack · Clutch operation
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 130 PSID 27 FMI 0 to MID 130 PSID 27 FMI 14 are all about the clutch operation. 1 needs an immediate stop. Start with this check: check the clutch wear reading on the scan tool and compare it with the service limit.

How urgent are they?

1 of 4 codes here means stop now; the other 3 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon3

What should I check first?

Check the clutch wear reading on the scan tool and compare it with the service limit

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 130 PSID 27 FMI 0Clutch disengages unintentionally

    The clutch disengages although it was not commanded, with no active clutch sensor, air pressure or valve codes and the control unit board hot.· Real condition
    Check soon

    Causes

    • Clutch valve assembly fault
    • Control unit board temperature issue
    • Intermittent air leak at the clutch cylinder

    Checks

    1. 1Check the clutch valve assembly for leaks for damage, corrosion or looseness
    2. 2Check the control unit temperature in the scan tool
    3. 3Check for other active clutch codes
    4. 4Replace the valve assembly
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 130 PSID 27 FMI 11Clutch drag

    The clutch is transferring too much torque in the disengaged position, so the truck creeps and the clutch wears quickly.· Other
    Check soon

    Causes

    • Clutch worn or glazed
    • Warped flywheel
    • Transmission input shaft fault

    Checks

    1. 1Check the clutch disengagement point calibration with the tool
    2. 2Inspect the clutch and flywheel
    3. 3Check the transmission input shaft
    4. 4Replace the clutch as needed
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Volvo/Mack MID 130 PSID 27 FMI 12Clutch slipping

    The clutch cannot transfer the requested torque without slipping.· Part or controller
    Check soon

    Causes

    • Worn clutch
    • Oil contamination on the clutch
    • Weak clutch pressure plate

    Checks

    1. 1Check the clutch wear value in the scan tool for damage, corrosion or looseness
    2. 2Check for oil leaks at the engine rear seal and the transmission input seal
    3. 3Inspect the clutch and pressure plate for damage, corrosion or looseness
    4. 4Replace the clutch once the slipping is confirmed and the actuator, air supply and sensors are proven good
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 130 PSID 27 FMI 14Clutch cannot disengage - Engine shut down

    The clutch system cannot disengage the clutch.· Other
    Stop now

    Causes

    • Clutch actuator or valve assembly failure
    • Mechanical clutch fault
    • Loss of air supply to the clutch cylinder

    Checks

    1. 1Do not keep driving; arrange a tow if needed before you replace any parts
    2. 2Check the clutch actuator, air supply and clutch valve assembly
    3. 3Check the clutch condition and the release mechanism
    4. 4Check which other clutch and air pressure codes are stored, since they often show the real cause
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the clutch wear reading on the scan tool and compare it with the service limit
  2. 2Check the air supply to the clutch actuator
  3. 3Check the clutch position sensor reading and calibration, because a wrong position gives false faults
  4. 4Check the clutch actuator valves for sticking and leaks and watch their response when commanded

Causes

  • Worn clutch or air supply problem
  • Clutch actuator or valve fault
  • Position sensor fault

When to stop

You'll notice: The truck may not move off, shifts harshly or the engine shuts down, and a lamp comes on.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.