EF Logo

Kubota · Engine ECU - SPN / FMI codes

Kubota Coolant, intake air temperature, oil pressure and overheat fault codes

This page covers engine temperature and oil protection: coolant and engine temperature sensors, overheat warnings, intake air temperature sensors, engine oil pressure and the engine overrun code. The engine ECU reads intake air, coolant and fuel temperature through thermistor sensors, whose resistance falls as they warm up.

More about these parts

The engine ECU first warns that the coolant is approaching the limit and then raises an overheat code when it passes it. The coolant temperature sensor is a thermistor in the engine coolant outlet. Two intake air temperature elements feed the engine ECU: one built into the mass air flow sensor and one separate sensor in the air intake.

FaultStopSPN100-FMI1Kubota · Coolant, intake air temperature, oil pressure and overheat
Code shows hereFAULTSPN100-FMI1

Where this code shows

Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.

What do these codes mean?

Kubota codes SPN100-FMI1 to E:9118 are all about the coolant, intake air temperature, oil pressure and overheat. The most common failure type is shorted high (4 of 15); 5 need an immediate stop. Start with this check: compare the sensor value in Diagmaster with a measured temperature on the engine.

How urgent are they?

5 of 15 codes here mean stop now; the other 10 can wait until the shift ends, but find the cause before the next one.

  • Stop now5
  • Check soon10

What should I check first?

Compare the sensor value in Diagmaster with a measured temperature on the engine

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Kubota SPN100-FMI1Engine oil pressure low

    SPN 100 FMI 1 means oil pressure dropped below the safe limit.· Real condition
    Stop now

    Causes

    • Engine oil level below the pickup tube
    • Oil filter or strainer blocked by sludge
    • Oil thinned by fuel dilution after repeated failed regenerations
    • Worn main or rod bearings leaking oil pressure

    Checks

    1. 1Shut the engine down at once and read the dipstick for level, colour and fuel smell
    2. 2Fit a mechanical gauge at the sender port and read pressure at idle and warm
    3. 3Replace the oil and filter if the oil is thin or dirty, then retest the pressure
    4. 4Compare the gauge reading with the dash; if the gauge is good and the dash is low, check the sensor and its wiring
    5. 5If pressure stays low with fresh oil, stop and have the bearings and oil pump inspected
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN110-FMI0Engine overheat - Coolant temperature extremely high

    SPN 110 FMI 0 is a real or measured overheat: coolant temperature reached the most severe level.· Real condition
    Stop now

    Causes

    • Low coolant or a leak
    • Radiator or oil cooler blocked
    • Fan, belt or water pump failure
    • Thermostat stuck closed

    Checks

    1. 1Stop the machine, idle without load and let the engine cool before opening the cap
    2. 2Check the coolant level and look for leaks at hoses, pump and radiator
    3. 3Clean the cooling stack of dust, chaff and debris
    4. 4Verify the cooling fan runs and the drive belt is tight and unglazed
    5. 5Test the thermostat and check the temperature sensor against a thermometer
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN110-FMI3Coolant temperature sensor - Short to battery

    SPN 110 FMI 3 means the coolant temperature signal is above range, typically a short to supply voltage or an open sensor ground.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to a supply line
    • Sensor ground wire open
    • Failed sensor element

    Checks

    1. 1Read coolant temperature in Diagmaster on a cold engine; a very high value confirms the fault
    2. 2Check the sensor ground wire for an open circuit back to the ECU
    3. 3Measure the sensor resistance with the plug removed
    4. 4Look for a signal wire touching a 5 V or 12 V line
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN110-FMI4Coolant temperature sensor - Open circuit or short to ground

    SPN 110 FMI 4 means the coolant temperature signal is below range, typically an open circuit or short to ground.· Shorted low
    Check soon

    Causes

    • Open coolant temperature signal wire
    • Signal wire shorted to ground
    • Coolant sensor failed
    • Corroded sensor connector

    Checks

    1. 1Compare the displayed coolant temperature with an infrared reading on the thermostat housing
    2. 2Unplug the sensor and measure its resistance cold and warm; it should fall as the engine heats
    3. 3Check the signal wire for continuity and a short to ground
    4. 4Inspect the connector for corrosion and bent pins
    5. 5Replace the sensor if resistance does not follow temperature
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN171-FMI3Intake air temperature sensor (built into MAF) - Short to battery

    SPN 171 FMI 3 means the intake air temperature signal is above its range, typically a short to supply voltage or a reference line touching the signal.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to a 5 V or 12 V line
    • Damaged MAF connector bridging two terminals
    • Failed MAF electronics

    Checks

    1. 1Read intake air temperature in Diagmaster; a value far above ambient on a cold engine confirms the high-side fault
    2. 2Unplug the MAF and see whether the reading drops to its open-circuit value or stays high
    3. 3Check the signal wire for a short to other circuits with the key off
    4. 4Inspect the connector for wet terminals or crossed pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN171-FMI4Intake air temperature sensor (built into MAF) - Open circuit or short to ground

    SPN 171 FMI 4 means the intake air temperature element inside the mass air flow sensor reads below its range, usually an open circuit or a short to ground.· Shorted low
    Check soon

    Causes

    • Open signal wire between the MAF connector and the ECU
    • Signal wire rubbed through and touching ground
    • Failed temperature element inside the MAF

    Checks

    1. 1Read the intake air temperature in Diagmaster with the engine cold; a reading far below ambient confirms the low-side fault
    2. 2Unplug the MAF and check the signal wire for continuity to the ECU and for a short to ground
    3. 3Measure resistance at the sensor pins; an open or near-zero reading means a failed element
    4. 4Inspect the MAF connector for corrosion and bent terminals
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN172-FMI3Intake air temperature sensor - Open circuit or short to battery

    SPN 172 FMI 3 means the intake air temperature sensor signal reads above its range, which points to an open circuit or a short to battery positive.· Shorted high
    Check soon

    Causes

    • Open signal or ground wire letting the signal float high
    • Signal wire shorted to battery positive
    • Failed intake air temperature sensor or corroded connector

    Checks

    1. 1Unplug the intake air temperature sensor and check the signal and ground wires for continuity back to the ECU
    2. 2With the key on, measure the signal wire for voltage above the 5 V supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN172-FMI4Intake air temperature sensor - Open circuit or short to ground

    SPN 172 FMI 4 means the intake air temperature sensor signal reads below its range, which points to an open circuit or a short to ground.· Shorted low
    Check soon

    Causes

    • Open circuit in the intake air temperature sensor signal or ground wire
    • Signal wire shorted to ground
    • Failed intake air temperature sensor or corroded connector

    Checks

    1. 1Unplug the intake air temperature sensor and check the signal wire for continuity to the ECU and for a short to ground
    2. 2Inspect the intake air temperature sensor connector for water, corrosion and pushed-back pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN190-FMI0Engine overrun

    SPN 190 FMI 0 means the engine speed went above the allowed maximum.· Real condition
    Stop now

    Causes

    • Machine driven downhill or pushed by the load above the governed speed
    • Crankshaft position sensor giving a wrong speed signal
    • Accelerator command stuck high
    • Oil or fuel drawn into the intake feeding the engine

    Checks

    1. 1Ask how the machine was driven when the code appeared and check the stored freeze-frame in Diagmaster
    2. 2Check the crankshaft sensor and its wiring for a false speed signal
    3. 3Inspect the intake and turbocharger for oil carry-over
    4. 4Check the accelerator signal and the governor settings with Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota E:9103Intake air temperature sensor system error

    The intake air temperature sensor reading is outside its normal range.· Other
    Check soon

    Causes

    • Intake air temperature sensor open or shorted
    • Sensor connector fault
    • Sensor built into the MAF failed

    Checks

    1. 1Read the sensor temperature in Diagmaster; with a cold engine it should match ambient
    2. 2Check the connector for water, corrosion and bent terminals
    3. 3Measure the sensor resistance and compare it with the manual curve
    4. 4Check the signal wires for an open circuit or a short to ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9104Coolant temperature system error

    The coolant temperature sensor signal is out of range or implausible.· Erratic or implausible
    Check soon

    Causes

    • Coolant temperature sensor failed
    • Sensor wire open or shorted
    • Thermostat stuck open giving an implausible reading

    Checks

    1. 1Compare the displayed coolant temperature with an infrared reading on the thermostat housing
    2. 2Measure the sensor resistance while the engine warms; it should fall steadily
    3. 3Inspect the connector and wires for damage and corrosion
    4. 4Check that the thermostat opens at its rated temperature
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota E:9105Fuel temperature sensor system error

    The fuel temperature sensor signal is out of its normal range.· Other
    Check soon

    Causes

    • Fuel temperature sensor failed
    • Open or short in its wiring
    • Connector corrosion

    Checks

    1. 1Read fuel temperature in Diagmaster against ambient when the engine is cold
    2. 2Check the connector and wires for damage, oil and corrosion
    3. 3Measure the sensor resistance and compare it with the manual curve
    4. 4Verify the fuel return lines are not heating the fuel in the tank
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9114Pre-overheat

    The engine is getting hot and the ECU warns before it reaches the overheat limit.· Real condition
    Check soon

    Causes

    • Radiator fins blocked
    • Low coolant
    • Fan not running

    Checks

    1. 1Check the coolant level and look for leaks at hoses and the pump
    2. 2Clean the radiator and oil cooler of dust, chaff and debris
    3. 3Confirm the fan operates and spins at the right speed
    4. 4Check the belt tension and condition for slipping
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota E:9116Engine overheat warning

    The engine coolant temperature is above the limit.· Shorted high
    Stop now

    Causes

    • Low coolant level
    • Radiator blocked
    • Fan or fan drive failed
    • Water pump or thermostat failure

    Checks

    1. 1Stop the engine and let it cool before you open the radiator cap
    2. 2Check the coolant level and look for external leaks and oil in coolant
    3. 3Clean the radiator and oil cooler of dust and debris
    4. 4Check the fan, belt and fan drive for slipping or damage
    5. 5Test the thermostat and water pump if the cooling stack is clean
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota E:9118Engine oil pressure system error

    The engine oil pressure is low or the sensor circuit reports a fault.· Other
    Stop now

    Causes

    • Low oil level
    • Oil pump or pickup worn or blocked
    • Oil pressure sensor failed
    • Wiring fault

    Checks

    1. 1Stop the engine and check the oil level on the dipstick
    2. 2Test oil pressure with a mechanical gauge at the sender port
    3. 3Check the sensor wiring and connector for damage
    4. 4Replace the sensor only if the gauge shows good pressure
    5. 5Look for oil dilution by fuel or coolant and for bearing wear
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Compare the sensor value in Diagmaster with a measured temperature on the engine
  2. 2Stop the engine, let it cool and check the coolant level
  3. 3Compare the displayed temperature with an infrared reading on the thermostat housing
  4. 4Compare the temperature in Diagmaster with the ambient air when the engine is cold
  5. 5Unplug the sensor and measure its resistance cold, then warm
  6. 6Clean the radiator and oil cooler from the back and look for leaks
  7. 7Unplug the sensor and measure its resistance cold and warm

Causes

  • Low engine oil level or a worn oil pump
  • Open or shorted sensor wire
  • Radiator and oil cooler blocked with dirt
  • Sensor wire open, shorted or chafed

Most common here: shorted high (4 of 15)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Hard starting, white smoke or poor power with the E:91xx code and the engine ECU lamp.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.