John Deere · Main controller (MCZ) - temperature
John Deere Fault Code MCZ 11901.03
Hydraulic oil temperature sensor (B40) high
What does John Deere code MCZ 11901.03 mean?
The hydraulic oil temperature sensor (B40) signal is high (above 4.35 V). The machine may show a wrong oil temperature and skip warm-up logic. Urgency: check soon - the machine may derate or limit a function. Check first: unplug B40 and measure the harness signal pin voltage with the key on; near 5 V is what an open sensor gives.
- MCZ
- Which controller reports it
- 11901
- What is at fault
- .03
- How it failed
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Unplug B40 and measure the harness signal pin voltage with the key on; near 5 V is what an open sensor gives
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- B40 signal wire open between the tank-side sensor and the MCZ, or the plug left unplugged after service
- B40 thermistor failed open internally
- B40 signal shorted to the 5 V sensor supply in the harness
- Corroded B40 connector terminals adding resistance in the signal path
How it failed
You'll notice: The primary hydraulic oil temperature sensor (B40) reads as a very cold or open sensor.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Pump pressure and hydraulic oil temperature sensors
- MCZ 11206.03Pump 1 control pressure sensor (B36) signal highOtherCheck soon
- MCZ 11206.04Pump 1 control pressure sensor (B36) signal lowOtherCheck soon
- MCZ 11208.03Pump 2 control pressure sensor circuit highOtherCheck soon
- MCZ 11208.04Pump 2 control pressure sensor circuit lowOtherCheck soon
- MCZ 11901.03Hydraulic oil temperature sensor (B40) highOtherCheck soon
- MCZ 11901.04Hydraulic oil temperature sensor (B40) lowOtherCheck soon
- MCZ 11992.03Pump 2 control pressure sensor circuit voltage highShorted highCheck soon
- MCZ 11992.04Pump 2 control pressure sensor circuit voltage lowShorted lowCheck soon
- MCZ 11994.03Pump 1 control pressure sensor circuit voltage highShorted highCheck soon
Show the other 9 codesHide the other codes
- MCZ 11200.03Pump 1 delivery pressure sensor (B35) signal highOtherCheck soon
- MCZ 11200.04Pump 1 delivery pressure sensor (B35) signal lowOtherCheck soon
- MCZ 11201.03Fan pump delivery pressure sensor circuit highOtherCheck soon
- MCZ 11201.04Fan pump delivery pressure sensor circuit lowOtherCheck soon
- MCZ 11202.03Pump 2 delivery pressure sensor (B37) signal highOtherCheck soon
- MCZ 11202.04Pump 2 delivery pressure sensor (B37) signal lowOtherCheck soon
- MCZ 11994.04Pump 1 control pressure sensor circuit voltage lowShorted lowCheck soon
- MCZ 15011.03Secondary hydraulic oil temperature sensor (B68) highOpen circuitCheck soon
- MCZ 15011.04Secondary hydraulic oil temperature sensor (B68) lowShorted lowCheck soon
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists MCZ 11901.03 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
