JLG · Outputs (valves and coils)
JLG Platform level and platform rotate valves fault codes
Platform level up/down tilts the basket to keep it level, and platform rotate left/right turns the basket. Each direction is a solenoid coil on the boom valve block at the platform end.
More about these partsLess
They are monitored both by the ground module and by the platform valve block driver (flash code 3-4), so one coil can appear under two code numbers, with short to ground, open circuit or short to battery for each.
Where this code shows
Turn the key on and watch the fault lamp or platform display.
What do these codes mean?
JLG codes 3-4 to 3414 are all about the platform level and platform rotate valves. The most common failure type is shorted high (8 of 24); none needs an immediate stop. Start with this check: read the Help message to see which of level up, level down, rotate left or rotate right is named.
How urgent are they?
None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.
- Check soon24
What should I check first?
Read the Help message to see which of level up, level down, rotate left or rotate right is named
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Platform Level Up Valve5 codes
JLG 342Platform Level Up Valve: Short to battery
Same fault as 3384 (Platform Level Up Valve - short to battery) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3384 section for the repair.· Shorted highShorted highCheck soonCauses
- The coil or wire fault described under 3384
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3384 checks on the same coil and plug at the platform valve block
- 2Compare the history: 342 together with 3384 means one fault, 342 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform level up valve plug and its pins match the failure named: short to battery
- 4Measure voltage on the signal lead with the coil unplugged and key on, then confirm the tilt-up cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 343Platform Level Up Valve: Short to ground
Same fault as 3382 (Platform Level Up Valve - short to ground) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3382 section for the repair.· Shorted lowShorted lowCheck soonCauses
- The coil or wire fault described under 3382
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3382 checks on the same coil and plug at the platform valve block
- 2Compare the history: 343 together with 3382 means one fault, 343 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform level up valve plug and its pins match the failure named: short to ground
- 4Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the tilt-up cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3382Platform Level Up Valve: Short to ground
The controller sees the platform level up valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Burnt turns grounding the platform level up valve output
- Level up coil shorted by water in the boom block, so the basket stays pitched
- Wire chafed through to the frame where the harness runs out along the boom and crosses the telescope section
- Dirt and water bridging a pin to ground; the level up plug rides along the boom and is the first to take wash water
Checks
- 1Separate the connector on the boom valve block and see whether the code goes with the load
- 2With the plug off, check the signal wire to the frame (it should be open), starting where the harness runs out along the boom and crosses the telescope section
- 3Press level up at the platform and listen for the solenoid click on the boom block, then watch the basket tilt; the analyzer output should go to supply, not stay at zero
- 4Dry the boom block plug and recheck; a coil that was only wet will clear
- 5Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the tilt-up cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3383Platform Level Up Valve: Open circuit
The controller drives the platform level up valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Winding burnt through at one end so the coil reads open
- Level up solenoid open, so the basket cannot be tilted up and drifts nose-down as the boom is raised
- Conductor snapped in the harness where the harness runs out along the boom and crosses the telescope section
- Terminal pushed back or plug not latched, since the level up plug rides along the boom and is the first to take wash water
Checks
- 1Check the coil on the boom valve block for an open winding, comparing with a good one if you have it
- 2Meter the wires end to end while someone moves the harness where the harness runs out along the boom and crosses the telescope section
- 3Command the output from the analyzer and press level up at the platform and listen for the solenoid click on the boom block, then watch the basket tilt
- 4Try level down: if it works the platform level circuit is alive and only the up coil is open
- 5Measure continuity of both leads from the plug back to the driver terminal, then confirm the tilt-up cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3384Platform Level Up Valve: Short to battery
The controller reads battery voltage on the platform level up valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Output wire touching a battery-fed wire where two harness legs cross
- Level up wire touching a supply wire along the boom, so the basket tilts up by itself
- Chafed insulation where the harness runs out along the boom and crosses the telescope section letting a feed touch the output wire
- Water tracking between supply and signal pins (the level up plug rides along the boom and is the first to take wash water)
Checks
- 1Check for supply on the output wire at the open connector on the boom valve block
- 2Feel along the harness where the harness runs out along the boom and crosses the telescope section for scuffed, hard or discoloured insulation
- 3Press level up at the platform and listen for the solenoid click on the boom block, then watch the basket tilt; battery voltage should appear on the output only when it is commanded on
- 4Watch the basket with the boom stopped: tilting without any switch pressed shows the output is held on
- 5Measure voltage on the signal lead with the coil unplugged and key on, then confirm the tilt-up cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Platform Level Down Valve6 codes
JLG 345Platform Level Down Valve: Open circuit
Same fault as 3389 (Platform Level Down Valve - open circuit) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3389 section for the repair.· Open circuitOpen circuitCheck soonCauses
- The coil or wire fault described under 3389
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3389 checks on the same coil and plug at the platform valve block
- 2Compare the history: 345 together with 3389 means one fault, 345 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform level down valve plug and its pins match the failure named: open circuit
- 4Measure continuity of both leads from the plug back to the driver terminal, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 346Platform Level Down Valve: Short to battery
Same fault as 3390 (Platform Level Down Valve - short to battery) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3390 section for the repair.· Shorted highShorted highCheck soonCauses
- The coil or wire fault described under 3390
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3390 checks on the same coil and plug at the platform valve block
- 2Compare the history: 346 together with 3390 means one fault, 346 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform level down valve plug and its pins match the failure named: short to battery
- 4Measure voltage on the signal lead with the coil unplugged and key on, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 347Platform Level Down Valve: Short to ground
Same fault as 3388 (Platform Level Down Valve - short to ground) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3388 section for the repair.· Shorted lowShorted lowCheck soonCauses
- The coil or wire fault described under 3388
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3388 checks on the same coil and plug at the platform valve block
- 2Compare the history: 347 together with 3388 means one fault, 347 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform level down valve plug and its pins match the failure named: short to ground
- 4Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3388Platform Level Down Valve: Short to ground
The controller sees the platform level down valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Level down coil shorted after flexing cracked its insulation at the boom block
- Wire chafed through to the frame at the boom block where the cable flexes every time the boom is raised or lowered
- Dirt and water bridging a pin to ground; the level down connector is on the boom block and its latch wears from constant flexing
Checks
- 1Pull the plug on the boom valve block and recycle EMS to see whether the code stays
- 2Meter the signal wire to the frame, flexing it at the boom block where the cable flexes every time the boom is raised or lowered for a reading that comes and goes
- 3Press level down at the platform, listen for the click, and see whether the basket tips back; the analyzer output should go to supply, not stay at zero
- 4Flex the level down lead at the boom block while metering to the frame; a reading that appears under flexing is the short
- 5Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3389Platform Level Down Valve: Open circuit
The controller drives the platform level down valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Level down solenoid open, so the basket will not tip back and stays pitched up
- Wire broken inside its insulation at the boom block where the cable flexes every time the boom is raised or lowered
- Terminal worn loose in its housing (the level down connector is on the boom block and its latch wears from constant flexing)
Checks
- 1Ohm the solenoid coil on the boom valve block with the plug off and compare with a matching good coil
- 2Check continuity from the module output pin to the plug, wiggling the wire as you test, starting at the boom block where the cable flexes every time the boom is raised or lowered
- 3Command the output from the analyzer and press level down at the platform, listen for the click, and see whether the basket tips back
- 4Try level up: if it works the circuit is alive and only the down coil is open
- 5Measure continuity of both leads from the plug back to the driver terminal, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3390Platform Level Down Valve: Short to battery
The controller reads battery voltage on the platform level down valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Output wire touching a battery-fed wire where two harness legs cross
- Level down wire touching a feed on the boom, so the basket tips down by itself
- Melted insulation at the boom block where the cable flexes every time the boom is raised or lowered
- Crushed pin touching a live neighbour; the level down connector is on the boom block and its latch wears from constant flexing
Checks
- 1Pull the plug on the boom valve block, key on, and check the output wire for voltage; if it stays with the load off, suspect the module
- 2Look for a wire crossing a live feed at the boom block where the cable flexes every time the boom is raised or lowered, and separate or replace it
- 3Watch the analyzer output as you press level down at the platform, listen for the click, and see whether the basket tips back
- 4Check the basket stays still with no switch pressed; drifting down means the output is held on
- 5Measure voltage on the signal lead with the coil unplugged and key on, then confirm the tilt-down cylinder line actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Platform Rotate Left Valve6 codes
JLG 349Platform Rotate Left Valve: Open circuit
Same fault as 3395 (Platform Rotate Left Valve - open circuit) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3395 section for the repair.· Open circuitOpen circuitCheck soonCauses
- The coil or wire fault described under 3395
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3395 checks on the same coil and plug at the platform valve block
- 2Compare the history: 349 together with 3395 means one fault, 349 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate left valve plug and its pins match the failure named: open circuit
- 4Measure continuity of both leads from the plug back to the driver terminal, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3394Platform Rotate Left Valve: Short to ground
The controller sees the platform rotate left valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Rotate left coil shorted after the harness twisted at the rotator wore its insulation through
- Wire chafed through to the frame at the rotator, where the harness is twisted every time the basket turns left
- Dirt and water bridging a pin to ground; the rotate left plug turns with the basket, so its seal and latch are stressed all day
Checks
- 1Unplug the platform rotate left valve on the platform rotator valve; if the code clears the solenoid coil is the short, if not the wiring or module is
- 2Test the output wire to the chassis with the connector open; any path is the short, most likely at the rotator, where the harness is twisted every time the basket turns left
- 3Press rotate left at the platform and listen for the click at the rotator valve, then watch the basket turn; the analyzer output should go to supply, not stay at zero
- 4Check the wire where it passes through the rotator for scuffing before blaming the coil
- 5Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3395Platform Rotate Left Valve: Open circuit
The controller drives the platform rotate left valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Rotate left coil open, so the basket will not turn left but may still turn right
- Harness fatigued and parted at the rotator, where the harness is twisted every time the basket turns left
- Pin backed out or loose in the connector, because the rotate left plug turns with the basket, so its seal and latch are stressed all day
Checks
- 1Unplug the platform rotate left valve on the platform rotator valve and measure across its two pins; an open reading means a dead solenoid coil
- 2Meter the wires end to end while someone moves the harness at the rotator, where the harness is twisted every time the basket turns left
- 3Command the output from the analyzer and press rotate left at the platform and listen for the click at the rotator valve, then watch the basket turn
- 4Turn the basket the other way: if that works, the rotator hydraulics are fine and only the left coil is open
- 5Measure continuity of both leads from the plug back to the driver terminal, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3396Platform Rotate Left Valve: Short to battery
The controller reads battery voltage on the platform rotate left valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Lead rubbed through against a live cable
- Rotate left wire touching a feed at the rotator, so the basket turns left by itself
- Harness rubbed bare and touching a feed at the rotator, where the harness is twisted every time the basket turns left
- Corrosion between pins in the plug (the rotate left plug turns with the basket, so its seal and latch are stressed all day)
Checks
- 1With the load off on the platform rotator valve and the key on, any reading on the output wire is the short
- 2Trace the wire alongside any supply wire and look for a touch point at the rotator, where the harness is twisted every time the basket turns left
- 3Watch the analyzer output as you press rotate left at the platform and listen for the click at the rotator valve, then watch the basket turn
- 4Keep clear of the basket and check whether it creeps left with no switch pressed
- 5Measure voltage on the signal lead with the coil unplugged and key on, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 3410Platform Rotate Left Valve: Short to battery
Same fault as 3396 (Platform Rotate Left Valve - short to battery) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3396 section for the repair.· Shorted highShorted highCheck soonCauses
- The coil or wire fault described under 3396
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3396 checks on the same coil and plug at the platform valve block
- 2Compare the history: 3410 together with 3396 means one fault, 3410 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate left valve plug and its pins match the failure named: short to battery
- 4Measure voltage on the signal lead with the coil unplugged and key on, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 3411Platform Rotate Left Valve: Short to ground
Same fault as 3394 (Platform Rotate Left Valve - short to ground) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3394 section for the repair.· Shorted lowShorted lowCheck soonCauses
- The coil or wire fault described under 3394
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3394 checks on the same coil and plug at the platform valve block
- 2Compare the history: 3411 together with 3394 means one fault, 3411 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate left valve plug and its pins match the failure named: short to ground
- 4Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the rotator motor port marked left actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Platform Rotate Right Valve6 codes
JLG 3397Platform Rotate Right Valve: Short to ground
The controller sees the platform rotate right valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Coil winding rubbing its own case until it earths
- Rotate right coil shorted by water that has entered the rotator plug
- Signal wire rubbed bare on metal at the rotator, where the cable winds up as the basket is turned right
- Wet or corroded plug, since the rotate right connector moves with the basket and loosens over time
Checks
- 1Pull the plug on the platform rotator valve and recycle EMS to see whether the code stays
- 2Meter between the signal pin and chassis with the plug apart; a reading shows the earth path, probably at the rotator, where the cable winds up as the basket is turned right
- 3With the analyzer open, press rotate right at the platform and listen for the click, then watch whether the basket rotates clockwise and watch the output state
- 4Dry the rotator plug and recheck; also meter the right coil to its case
- 5Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 3398Platform Rotate Right Valve: Open circuit
The controller drives the platform rotate right valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Rotate right coil open, so the basket will not turn right but may still turn left
- Wire work-hardened and snapped inside its sheath at the rotator, where the cable winds up as the basket is turned right
- Terminal pushed back or plug not latched, since the rotate right connector moves with the basket and loosens over time
Checks
- 1Check the coil on the platform rotator valve for an open winding, comparing with a good one if you have it
- 2Check continuity from the module output pin to the plug, wiggling the wire as you test, starting at the rotator, where the cable winds up as the basket is turned right
- 3Command the output from the analyzer and press rotate right at the platform and listen for the click, then watch whether the basket rotates clockwise
- 4Turn the basket left to prove the rotator hydraulics work, then chase the right coil circuit
- 5Measure continuity of both leads from the plug back to the driver terminal, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3399Platform Rotate Right Valve: Short to battery
The controller reads battery voltage on the platform rotate right valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Lead rubbed through against a live cable
- Rotate right wire touching a feed at the rotator so the basket turns right by itself
- Damaged sheath at the rotator, where the cable winds up as the basket is turned right, exposing the wire to a live one
- Water tracking between supply and signal pins (the rotate right connector moves with the basket and loosens over time)
Checks
- 1Check for supply on the output wire at the open connector on the platform rotator valve
- 2Look for a wire crossing a live feed at the rotator, where the cable winds up as the basket is turned right, and separate or replace it
- 3Watch the analyzer output as you press rotate right at the platform and listen for the click, then watch whether the basket rotates clockwise
- 4Keep clear and see whether the basket drifts right with no switch pressed
- 5Measure voltage on the signal lead with the coil unplugged and key on, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 3412Platform Rotate Right Valve: Open circuit
Same fault as 3398 (Platform Rotate Right Valve - open circuit) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3398 section for the repair.· Open circuitOpen circuitCheck soonCauses
- The coil or wire fault described under 3398
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3398 checks on the same coil and plug at the platform valve block
- 2Compare the history: 3412 together with 3398 means one fault, 3412 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate right valve plug and its pins match the failure named: open circuit
- 4Measure continuity of both leads from the plug back to the driver terminal, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 3413Platform Rotate Right Valve: Short to battery
Same fault as 3399 (Platform Rotate Right Valve - short to battery) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3399 section for the repair.· Shorted highShorted highCheck soonCauses
- The coil or wire fault described under 3399
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3399 checks on the same coil and plug at the platform valve block
- 2Compare the history: 3413 together with 3399 means one fault, 3413 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate right valve plug and its pins match the failure named: short to battery
- 4Measure voltage on the signal lead with the coil unplugged and key on, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 3414Platform Rotate Right Valve: Short to ground
Same fault as 3397 (Platform Rotate Right Valve - short to ground) reported by the platform valve block driver (flash code 3-4) instead of the ground module, so one wiring or coil problem can raise both numbers. Use the 3397 section for the repair.· Shorted lowShorted lowCheck soonCauses
- The coil or wire fault described under 3397
- The fault sits at the platform end, which is why the valve block driver saw it before the ground module
Checks
- 1Follow the 3397 checks on the same coil and plug at the platform valve block
- 2Compare the history: 3414 together with 3397 means one fault, 3414 alone means the driver output on the valve block itself
- 3Confirm on the valve block driver side that the platform rotate right valve plug and its pins match the failure named: short to ground
- 4Measure insulation resistance between the lead and the boom frame with the plug open, then confirm the rotator motor port marked right actually moves oil when the coil is energised
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Other codes1 code
JLG 3-4Platform valve block driver fault
Same driver check as 3-3 but on a platform valve block output (basket level, rotate, jib, platform control valve). Mostly seen on machines with electronic basket levelling.· OtherOtherCheck soonCauses
- Open coil on the platform level, rotate or jib valve
- Platform harness damaged where it flexes along the boom
- Short to battery or ground in the platform valve harness
- Platform valve connector wet or corroded
- Output driver damaged in the module
Checks
- 1Read the Help message to see which platform valve is named
- 2Measure the named coil's resistance at the valve with the plug off
- 3Check the wire from the module to that coil for continuity and for a short to the frame
- 4Inspect the valve plug for water and green corrosion
- 5Cycle EMS, command the function again and watch the output state in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read the Help message to see which of level up, level down, rotate left or rotate right is named
- 2Operate that switch at the platform and listen for the coil click on the boom block
- 3Unplug the named coil and recycle EMS; a changed code points at the coil, an unchanged one at the harness or driver
- 4Ohm the coil and each pin to the valve body, then look along the boom harness for rub marks and moisture
- 5Retest and confirm the basket moves smoothly in both directions
Causes
- A level or rotate coil failed from water in the boom valve block or age
- Boom harness chafed through to the frame where it runs out along the telescope section
- Loose or corroded plug on the platform valve block
- Output driver in the ground module or valve block driver damaged
Most common here: shorted high (8 of 24)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The basket will not tilt or will not rotate in the named direction, drifts out of level as the boom moves, or turns by itself when a coil is held on.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- JLG 600S/660SJ Service and Maintenance Manual 3121298, section 6 (Table 6-8 Fault Code List)
- JLG 600S/600SJ/660SJ/600A/AJ Service and Maintenance Manual 3120840, section 6 (Tables 6-3, 6-5)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
