JLG · Platform / ground controls
JLG Fault Code 2‑3
Boom function selection fault
What does JLG code 2-3 mean?
A boom function (lift, swing, telescope, jib, level, rotate) was selected in the wrong order or its joystick or switch is bad: both directions at once, selected before key or footswitch, or selected before aux power. Lift/swing joystick faults also report here. Urgency: check soon - the machine may derate or limit a function. Check first: release all functions, cycle the footswitch and retry in the correct order.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Release all functions, cycle the footswitch and retry in the correct order
Then 4 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 5 done
Causes
- Function switch or lift/swing joystick moved before the footswitch or key was on
- Both directions of one function closed together (stuck rocker)
- Lift/swing joystick centre tap out of window or Q-Prox sensor fault
- Ground function selected before aux power was applied
1 more causeFewer causes
- Water in the platform control box shorting switch inputs
How it failed
You'll notice: A boom function (lift, swing, telescope, jib, level or rotate) refuses to move from the basket and the lamp flashes 2-3.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Footswitch, joysticks, steer switches and start sequence
- 2-1Footswitch or keyswitch faultReal conditionCheck soon
- 2-2Drive or steer selection faultOtherCheck soon
- 2-3Boom function selection faultOtherCheck soon
- 2-4Steering digital inputs faultyOtherCheck soon
- 2-7Accelerator input faultyOtherCheck soon
- 0011Footswitch openOtherInformation
- 213Footswitch faultyOtherCheck soon
- 224Function problem - steer left permanently selectedOtherCheck soon
- 225Function problem - steer right permanently selectedOtherCheck soon
Show the other 17 codesHide the other codes
- 227Steer switches faultyReal conditionCheck soon
- 234Function switches faulty - check diagnostics/boomReal conditionCheck soon
- 235Function switches locked - selected before aux powerOtherCheck soon
- 236Function switches locked - selected before start switchOtherCheck soon
- 237Start switch locked - selected before keyswitchOtherCheck soon
- 2211Footswitch interlock trippedReal conditionCheck soon
- 2212Drive locked - joystick moved before footswitchOtherCheck soon
- 2213Steer locked - selected before footswitchOtherCheck soon
- 2216Drive/steer joystick out of range highShorted highCheck soon
- 2217Drive/steer joystick centre tap badOtherCheck soon
- 2219Lift/swing joystick out of range highOtherCheck soon
- 2220Lift/swing joystick centre tap badOtherCheck soon
- 2221Lift/swing locked - joystick moved before footswitchOtherCheck soon
- 2222Waiting for footswitch to be openOtherInformation
- 2223Function switches locked - selected before enableOtherCheck soon
- 2224Footswitch selected before startOtherCheck soon
- 2310Function problem - ground enable permanently selectedOtherCheck soon
Other JLG codes: Platform / ground controls
Related on Equipments Finder
Source
JLG 600S/600SJ/660SJ/600A/AJ Service and Maintenance Manual 3120840, section 6 (Tables 6-3, 6-5)
This source lists 2-3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG boom lifts with the JLG Control System (600S, 600SJ, 660SJ, 600A/AJ, 450A, 510A, 400S, 1200/1350SJP families).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
