EF Logo

JCB · Aftertreatment ECU - SCR / DEF

JCB DEF module and tank heaters fault codes

The DEF tank heater thaws frozen DEF inside the tank, while the supply module heater and its temperature monitoring keep the pump unit warm enough to run. These are separate from the line heaters.

FaultCheckP20B5-13JCB · DEF module and tank heaters
Code shows hereFAULTP20B5-13

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P20B5-13 to P209F-4B are all about the dEF module and tank heaters. The most common failure type is erratic or implausible (3 of 14); none needs an immediate stop. Start with this check: measure the tank heater resistance at the head unit plug and compare it with the manual value.

How urgent are they?

None of the 14 codes here means stop now; all 14 can wait until the shift ends, but find the cause before the next one.

  • Check soon14

What should I check first?

Measure the tank heater resistance at the head unit plug and compare it with the manual value

Shared checks

14 of 14

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P20B5-13Supply module heater actuator open load

    Supply module heater actuator open load.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the supply module heater actuator open load
    • Supply module heater actuator open load coil, element or sensor internally open

    Checks

    1. 1Unplug the supply module heater actuator open load and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the supply module heater actuator open load plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20AD-06Supply module temperature error

    Supply module temperature error.· Other
    Check soon

    Causes

    • Supply module temperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the supply module temperature and look for a value that is stuck or implausible
    2. 2Check the supply module temperature connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20B6-4BSupply module heater powerstage overtemperature

    Supply module heater powerstage overtemperature.· Real condition
    Check soon

    Causes

    • Supply module heater powerstage overtemperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the supply module heater powerstage overtemperature and look for a value that is stuck or implausible
    2. 2Check the supply module heater powerstage overtemperature connector and wiring for damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P20B6-21Supply module heater temperature duty cycle below minimum range

    Supply module heater temperature duty cycle below minimum range.· Erratic or implausible
    Check soon

    Causes

    • Supply module heater temperature duty cycle below minimum range drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the supply module heater temperature duty cycle below minimum range circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the supply module heater temperature duty cycle below minimum range value on live data with a known good value or a reference gauge
    2. 2Check the supply module heater temperature duty cycle below minimum range connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P20B6-22DEF supply module heater over-temperature

    DEF supply module heater over-temperature.· Real condition
    Check soon

    Causes

    • DEF supply module heater over signal pulled high by a short to the 5 V reference or supply
    • Sensor or part failed giving a high reading

    Checks

    1. 1Read the DEF supply module heater over value on live data and compare it with the expected value
    2. 2Unplug the DEF supply module heater over and check the signal wire for a short to 5 V or battery
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P20B7-14Supply module heater powerstage short to ground

    Supply module heater powerstage short to ground.· Shorted low
    Check soon

    Causes

    • Wire for the supply module heater powerstage short to ground chafed and touching chassis or engine ground
    • Supply module heater powerstage short to ground coil or sensor shorted internally

    Checks

    1. 1Unplug the supply module heater powerstage short to ground and check each wire for a short to chassis ground
    2. 2Measure the resistance of the supply module heater powerstage short to ground and compare it with the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P20B8-15Supply module heater powerstage short to battery

    Supply module heater powerstage short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the supply module heater powerstage short to battery touching a battery-fed wire in the harness
    • Water or damage inside the supply module heater powerstage short to battery connector bridging to supply

    Checks

    1. 1Unplug the supply module heater powerstage short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the supply module heater powerstage short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P20AD-21Supply module temperature duty cycle below minimum range

    Supply module temperature duty cycle below minimum range.· Erratic or implausible
    Check soon

    Causes

    • Supply module temperature duty cycle below minimum range drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the supply module temperature duty cycle below minimum range circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the supply module temperature duty cycle below minimum range value on live data with a known good value or a reference gauge
    2. 2Check the supply module temperature duty cycle below minimum range connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P20AD-22Supply module temperature duty cycle above maximum range

    Supply module temperature duty cycle above maximum range.· Erratic or implausible
    Check soon

    Causes

    • Supply module temperature duty cycle above maximum range drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the supply module temperature duty cycle above maximum range circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the supply module temperature duty cycle above maximum range value on live data with a known good value or a reference gauge
    2. 2Check the supply module temperature duty cycle above maximum range connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P20AD-92Supply module temperature error during cold start

    Supply module temperature error during cold start.· Other
    Check soon

    Causes

    • Supply module temperature error during cold start or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the supply module temperature error during cold start and look for a value that is stuck or implausible
    2. 2Check the supply module temperature error during cold start connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P202A-13DEF tank heater open load

    The DEF tank heater circuit is open, so the heater is not working.· Open circuit
    Check soon

    Causes

    • Open circuit in the DEF tank heater element
    • Coolant heating valve not opening
    • Heater relay or fuse failed

    Checks

    1. 1Measure the heater resistance with the connector unplugged for an open circuit
    2. 2Check the tank heater fuse and relay for a blown fuse or dead relay
    3. 3Check the heater supply voltage and ground when it is commanded on
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P202B-14DEF tank heater powerstage short to ground

    DEF tank heater powerstage short to ground.· Shorted low
    Check soon

    Causes

    • Wire for the DEF tank heater powerstage short to ground chafed and touching chassis or engine ground
    • DEF tank heater powerstage short to ground coil or sensor shorted internally

    Checks

    1. 1Unplug the DEF tank heater powerstage short to ground and check each wire for a short to chassis ground
    2. 2Measure the resistance of the DEF tank heater powerstage short to ground and compare it with the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P202C-15DEF tank heater powerstage short to battery

    DEF tank heater powerstage short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the DEF tank heater powerstage short to battery touching a battery-fed wire in the harness
    • Water or damage inside the DEF tank heater powerstage short to battery connector bridging to supply

    Checks

    1. 1Unplug the DEF tank heater powerstage short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the DEF tank heater powerstage short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P209F-4BDEF tank heater powerstage overtemperature

    DEF tank heater powerstage overtemperature.· Real condition
    Check soon

    Causes

    • DEF tank heater powerstage overtemperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF tank heater powerstage overtemperature and look for a value that is stuck or implausible
    2. 2Check the DEF tank heater powerstage overtemperature connector and wiring for damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Measure the tank heater resistance at the head unit plug and compare it with the manual value
  2. 2Check the supply module connector for water, since the unit sits low on the machine
  3. 3Let the machine stand cold and check that the module temperature rises once the heater is commanded on
  4. 4Check the heater supply fuse and the aftertreatment unit supply voltage

Causes

  • Tank heater element or coolant valve failed
  • Supply module heater open or shorted inside the module
  • Heater driver stage overheated after a short
  • Module temperature sensor out of range at a cold start

Most common here: erratic or implausible (3 of 14)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: A DEF level or SCR warning may appear in freezing weather, and dosing may be delayed while the tank thaws.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.