J1939 · Aftertreatment - SCR/DEF
SPN 4360 Fault Code
Aftertreatment 1 SCR intake gas temperature
What does SPN 4360 mean?
Exhaust temperature entering the SCR catalyst, read by a sensor ahead of it. The ECM uses it to decide when DEF dosing is allowed. How urgent it is depends on the FMI after SPN 4360 - pick it below. Check first: compare the SCR intake temperature with the DPF outlet temperature; they should be very close at steady load.
- SPN 4360
- Aftertreatment 1 SCR intake gas temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 4360 - pick it below.
What should I check first?
Compare the SCR intake temperature with the DPF outlet temperature; they should be very close at steady load
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 4360?
You'll notice: The ECM cannot read the gas temperature at the SCR inlet, so it holds back DEF dosing because it cannot be sure the catalyst is warm enough.
Find the number shown after SPN 4360 on your display. FMI 3 has its own page with causes and checks.
- 0SPN 4360 FMI 0: Value is above the normal range, most severe levelReal conditionCummins ISX15
- 2SPN 4360 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15, Detroit DD13
- 3SPN 4360 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13
- 4SPN 4360 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13
- 8SPN 4360 FMI 8: SCR inlet temperature shows a spikeErratic or implausibleDetroit DD15, Detroit DD13
- 10SPN 4360 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 15SPN 4360 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15
- 16SPN 4360 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
- 20SPN 4360 FMI 20: The SCR inlet temperature sensor has drifted high in rangeErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 31SPN 4360 FMI 31: The SCR inlet temperature is not warming up as expectedReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 4360 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the SCR intake temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the SCR intake temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: exhaust leak between the filter and the dosing point cooling the gas before the sensor
- Real condition: catalyst not warming because the machine has been at light load, so the temperature is real but low
1 more causeFewer causes
- Sensor: dEF deposits on the sensor tip giving a slow, wandering reading
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 4360 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
