Deutz · Exhaust aftertreatment (SCR)
Deutz Fault Code SPN 3361 FMI 4
Exhaust aftertreatment - DEF metering unit - Voltage below normal or shorted to low source
What does Deutz code SPN 3361 FMI 4 mean?
The EMR4 sees the output for the DEF metering valve (dosing valve) (at the exhaust pipe in front of the SCR catalyst, injecting DEF) at a voltage below normal, as if the circuit is shorted to ground. Urgency: check soon - the machine may derate or limit a function. Check first: check the dosing valve for crystal deposits at the nozzle and for a spray pattern during a dosing test.
- FMI 4
- Voltage below normal or shorted low
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the dosing valve for crystal deposits at the nozzle and for a spray pattern during a dosing test
Then 4 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 5 done
Causes
- Water in the connector bridging the pins
- DEF metering valve (dosing valve) winding shorted to its housing
- Dosing nozzle blocked by crystallised DEF
How it failed
You'll notice: Expect a warning lamp; DEF cannot be injected, so NOx is not reduced; the SCR lamp comes on and power is reduced after a countdown.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DEF pump, metering unit and suction unit
3 other codes on this part are also shorted low (SPN 3361 FMI 6, SPN 4375 FMI 4, SPN 4376 FMI 4). When they show together, start at the wiring and connector they share.
- SPN 3361 FMI 3Exhaust aftertreatment - DEF metering unit - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 3361 FMI 4Exhaust aftertreatment - DEF metering unit - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3361 FMI 6Exhaust aftertreatment - DEF metering unit - Current above normal or grounded circuitShorted lowCheck soon
- SPN 3361 FMI 7Exhaust aftertreatment - DEF metering unit - Mechanical system not responding or out of adjustmentPart or controllerCheck soon
- SPN 4374 FMI 13Exhaust aftertreatment - DEF metering valve - Out of calibrationPart or controllerCheck soon
- SPN 4375 FMI 3Exhaust aftertreatment - DEF pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4375 FMI 4Exhaust aftertreatment - DEF pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 4375 FMI 5Exhaust aftertreatment - DEF pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 4376 FMI 3Exhaust aftertreatment - DEF reverse valve - Voltage above normal or shorted to high sourceShorted highCheck soon
Show the other 13 codesHide the other codes
- SPN 4376 FMI 4Exhaust aftertreatment - DEF reverse valve - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 4376 FMI 5Exhaust aftertreatment - DEF reverse valve - Current below normal or open circuitOpen circuitCheck soon
- SPN 4376 FMI 12Exhaust aftertreatment - DEF reverse valve - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523668 FMI 11Exhaust aftertreatment - Hardware failure temperature sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523669 FMI 11Exhaust aftertreatment - Hardware failure quality sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523670 FMI 11Exhaust aftertreatment - Hardware failure level sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523720 FMI 2Exhaust aftertreatment - Heater DEF metering unit - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523720 FMI 8Exhaust aftertreatment - Heater DEF metering unit - Abnormal frequency or pulse width or periodErratic or implausibleCheck soon
- SPN 524067 FMI 0Exhaust aftertreatment - DEF pump temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524067 FMI 1Exhaust aftertreatment - DEF pump temperature - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 524067 FMI 2Exhaust aftertreatment - DEF pump temperature - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524141 FMI 7Exhaust aftertreatment - DEF metering valve - Mechanical system not responding or out of adjustmentPart or controllerCheck soon
- SPN 524282 FMI 11Exhaust aftertreatment - Hardware failure temperature sensor DEF suction unit - Root cause not knownOtherCheck soon
Other Deutz codes: Exhaust aftertreatment (SCR)
- SPN 3519 FMI 3Exhaust aftertreatment - DEF tank temperature (DEF quality sensor) - Voltage above normal or shorted to high source
- SPN 3519 FMI 4Exhaust aftertreatment - DEF tank temperature (DEF quality sensor) - Voltage below normal or shorted to low source
- SPN 3519 FMI 12Exhaust aftertreatment - DEF tank temperature (DEF quality sensor) - Bad intelligent device or component
- SPN 3519 FMI 13Exhaust aftertreatment - DEF tank temperature (DEF quality sensor) - Out of calibration
- SPN 3520 FMI 1Exhaust aftertreatment - DEF quality sensor - Data below normal operational range (Most severe level)
- SPN 3520 FMI 2Exhaust aftertreatment - DEF quality sensor - Data erratic intermittent or incorrect
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 22
This source lists SPN 3361 FMI 4 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
