Deutz · ECU power and supply
Deutz Fault Code SPN 168 FMI 4
Machine - Battery voltage - Voltage below normal or shorted to low source
What does Deutz code SPN 168 FMI 4 mean?
The EMR4 measures the machine battery voltage (at the EMR4 supply connector, fed from the machine battery and ignition) below range or shorted to ground; the voltage at the EMR4 supply pin is too low. Urgency: check soon - the machine may derate or limit a function. Check first: check the main ground between engine block, frame and battery negative.
- FMI 4
- Voltage below normal or shorted low
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the main ground between engine block, frame and battery negative
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Alternator regulator failing and over- or undercharging
- Corroded battery terminal or ground strap
- High-resistance connection in the ignition or power feed to the EMR4
- Undervoltage points at a weak battery, high resistance in a power feed, or the alternator not charging
How it failed
You'll notice: Expect a warning lamp; you see a warning lamp, hard starting, or ECU resets, because the EMR4 needs a stable supply to drive the injectors.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: EMR4 controller, memory, supply and immobilizer
1 other code on this part is also shorted low (SPN 523612 FMI 4). When they show together, start at the wiring and connector they share.
- SPN 168 FMI 0Machine - Battery voltage - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 168 FMI 1Machine - Battery voltage - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 168 FMI 2Machine - Battery voltage - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 168 FMI 3Machine - Battery voltage - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 168 FMI 4Machine - Battery voltage - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 630 FMI 12Engine - ECU calibration memory - Bad intelligent device or componentPart or controllerStop now
- SPN 1079 FMI 13Engine - Sensor supply voltage - Out of calibrationPart or controllerCheck soon
- SPN 1080 FMI 13Engine - Sensor supply voltage 2 - Out of calibrationPart or controllerCheck soon
- SPN 1136 FMI 0Engine - ECU temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
Show the other 16 codesHide the other codes
- SPN 523008 FMI 1Engine - Manipulation monitoring - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 523008 FMI 2Engine - Manipulation monitoring - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523330 FMI 14Engine - Immobilizer - Special instructionsOtherCheck soon
- SPN 523601 FMI 13Engine - ECU Sensor supply voltage 3 - Out of calibrationPart or controllerCheck soon
- SPN 523612 FMI 3Engine - ECU - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523612 FMI 4Engine - ECU - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523612 FMI 12Engine - ECU - Bad intelligent device or componentPart or controllerStop now
- SPN 523612 FMI 14Engine - ECU - Special instructionsOtherCheck soon
- SPN 523704 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523935 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523936 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
- SPN 524052 FMI 11Engine - Dataset Main and Secondary ECU not identical - Root cause not knownOtherCheck soon
- SPN 524068 FMI 2Engine - ECU Main Secondary identical - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524233 FMI 11Engine - ECU EEPROM error Secondary - Root cause not knownPart or controllerCheck soon
- SPN 524277 FMI 11Engine - ECU afterun too often not waited - Root cause not knownOtherCheck soon
- SPN 524278 FMI 11Engine - ECU afterun too often consecutive not waited - Root cause not knownOtherCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 1
This source lists SPN 168 FMI 4 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
