Cummins · Air handling
Cummins Turbocharger speed and compressor inlet sensors fault codes
A speed sensor reads the turbine shaft rotation so the ECM can protect the turbo from overspeed and control boost. Sensors at the compressor inlet measure air pressure and temperature before the turbo, which lets the ECM correct boost and protect the turbo from surge or overheating.
More about these partsLess
The ECM calculates compressor outlet and turbine inlet temperature from other sensor readings rather than measuring them directly, and sets a fault when the calculated value gets too high.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 595 to 7861 are all about the turbocharger speed and compressor inlet sensors. The most common failure type is real condition (8 of 17); none needs an immediate stop. Start with this check: check the turbo shaft for play and the compressor wheel for damage before anything else.
How urgent are they?
None of the 17 codes here means stop now; 14 can wait until the shift ends, but find the cause before the next one; 3 are information only.
- Check soon14
- Info3
What should I check first?
Check the turbo shaft for play and the compressor wheel for damage before anything else
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Turbocharger 1 speed4 codes
Cummins 595Turbocharger 1 speed: Above normal· moderately severe
Same failure as 2288 on the turbocharger 1 speed: the same fault condition as 2288, reported for this part. The turbocharger speed sensor reads the turbo shaft speed, which the ECM uses to protect the turbo from overspeed and to check boost control.· Real conditionReal conditionCheck soonCauses
- Same causes as 2288, applied to the turbocharger 1 speed
- Wiring or connector problem local to the turbocharger 1 speed
Checks
- 1Inspect the speed sensor tip for contact with the compressor wheel nut and for oil or debris.
- 2Work through the checks listed for 2288, starting at the turbocharger 1 speed and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger 1 speed - above normal - moderately severe
Cummins 686Turbocharger 1 speed: Erratic reading
The ECM judges the turbocharger 1 speed to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact on the turbocharger 1 speed
- Part ageing or failing and giving unstable output
- Electrical noise from a poorly routed wire or a bad ground
Checks
- 1Watch the turbocharger 1 speed live in INSITE and wiggle the harness and connector to catch dropouts
- 2Compare the turbocharger 1 speed with a related reading to decide which one is wrong
- 3Check the connector for moisture and corrosion and the ground connection for tightness
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Turbocharger 1 speed - data erratic or incorrect
Cummins 687Turbocharger 1 speed: Below normal· moderately severe
The turbocharger 1 speed is below its normal range (severity: moderately severe). The ECM sets the code from a real reading, so look for a genuine cause before blaming the sensor.· Real conditionReal conditionCheck soonCauses
- A real shortfall in the system the turbocharger 1 speed measures
- Sensor or circuit reading low from a wiring fault
- A leak, low level or weak supply that lets the value fall
Checks
- 1Confirm the real condition with a gauge or a second reading before replacing the turbocharger 1 speed
- 2Check that the turbocharger 1 speed circuit codes are not active, since a wiring fault can fake a low reading
- 3Look for the physical cause upstream, such as a leak, low fluid, weak pump or blocked supply
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger 1 speed - below normal - moderately severe
Cummins 2288Turbocharger 1 speed: Above normal· least severe
The turbocharger 1 speed is above its normal range (severity: least severe). The ECM sets the code from a real reading, so look for a genuine cause before blaming the sensor.· Real conditionReal conditionInfoCauses
- A real over-limit condition in the system the turbocharger 1 speed measures
- Sensor or circuit reading high from a wiring fault
- A cooling, flow or restriction problem upstream that drives the value up
Checks
- 1Confirm the real condition with a gauge or a second reading before replacing the turbocharger 1 speed
- 2Check that the turbocharger 1 speed circuit codes are not active, since a wiring fault can fake a high reading
- 3Look for the physical cause upstream, such as restriction, leakage, poor cooling or heavy load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger 1 speed - above normal - least severe
Turbocharger 1 compressor inlet pressure1 code
Cummins 629Turbocharger 1 compressor inlet pressure: Below normal· moderately severe
Same failure as 687 on the turbocharger 1 compressor inlet pressure: the same fault condition as 687, reported for this part. The compressor inlet pressure sensor reads pressure before the compressor, so a clogged air filter or intake restriction shows up here first.· Real conditionReal conditionCheck soonCauses
- Same causes as 687, applied to the turbocharger 1 compressor inlet pressure
- Wiring or connector problem local to the turbocharger 1 compressor inlet pressure
Checks
- 1Check the air filter restriction and the intake piping for collapse or blockage.
- 2Work through the checks listed for 687, starting at the turbocharger 1 compressor inlet pressure and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger 1 compressor inlet pressure - below normal - moderately severe
Turbocharger 1 compressor intake temperature sensor circuit1 code
Cummins 691Turbocharger 1 compressor intake temperature sensor circuit: Voltage high / shorted high
The ECM reads the turbocharger 1 compressor intake temperature sensor circuit above its allowed voltage band. That points to a short to a 5 V or battery wire, a lost return, or a failed part, rather than a real change in what it measures.· Shorted highShorted highCheck soonCauses
- Short to a 5 V reference or a battery wire in the harness to the turbocharger 1 compressor intake temperature sensor circuit
- Open or high-resistance return wire that lets the signal float high
- Water or corrosion in the connector bridging two pins together
Checks
- 1Key on, unplug the turbocharger 1 compressor intake temperature sensor circuit and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
- 2Jumper the signal wire of the turbocharger 1 compressor intake temperature sensor circuit to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
- 3Check continuity and resistance of the return wire from the turbocharger 1 compressor intake temperature sensor circuit back to the ECM
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Turbocharger 1 compressor intake temperature sensor circuit - voltage high (shorted to a high source)
Turbocharger 1 compressor intake temperature circuit1 code
Cummins 692Turbocharger 1 compressor intake temperature circuit: Voltage low / shorted low
The ECM reads the turbocharger 1 compressor intake temperature circuit below its allowed voltage band. That points to a short to ground, an open supply or signal wire, or a failed part, not necessarily a real low value.· Shorted lowShorted lowCheck soonCauses
- Signal wire to the turbocharger 1 compressor intake temperature circuit rubbed through and shorted to ground or to the engine block
- Open 5 V reference or open signal wire that lets the input drop to zero
- Corroded or backed-out pin in the turbocharger 1 compressor intake temperature circuit connector
Checks
- 1Key on, unplug the turbocharger 1 compressor intake temperature circuit and read its circuit at the harness: a reading near zero with the part removed means the wiring is shorted to ground or open
- 2Jumper the 5 V reference to the signal wire at the harness and see whether the code changes to a high-voltage code, which proves the wiring and the ECM input
- 3Measure resistance from the turbocharger 1 compressor intake temperature circuit signal wire to ground with the ECM unplugged to find a short
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Turbocharger 1 compressor intake temperature circuit - voltage low (shorted to a low source)
Turbocharger 1 compressor intake temperature1 code
Cummins 693Turbocharger 1 compressor intake temperature: Erratic reading
Same failure as 686 on the turbocharger 1 compressor intake temperature: the same fault condition as 686, reported for this part. The compressor intake temperature sensor reads the air entering the turbo compressor, which the ECM uses to correct boost and calculate air density.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 686, applied to the turbocharger 1 compressor intake temperature
- Wiring or connector problem local to the turbocharger 1 compressor intake temperature
Checks
- 1Check the sensor is clear of the air filter housing connector and the intake piping is not leaking.
- 2Work through the checks listed for 686, starting at the turbocharger 1 compressor intake temperature and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Turbocharger 1 compressor intake temperature - data erratic or incorrect
Turbocharger 1 compressor intake pressure circuit2 codes
Cummins 741Turbocharger 1 compressor intake pressure circuit: Voltage high / shorted high
Same failure as 691 on the turbocharger 1 compressor intake pressure circuit: the same fault condition as 691, reported for this part. The compressor inlet pressure sensor reads pressure before the compressor, so a clogged air filter or intake restriction shows up here first.· Shorted highShorted highCheck soonCauses
- Same causes as 691, applied to the turbocharger 1 compressor intake pressure circuit
- Wiring or connector problem local to the turbocharger 1 compressor intake pressure circuit
Checks
- 1Check the air filter restriction and the intake piping for collapse or blockage.
- 2Work through the checks listed for 691, starting at the turbocharger 1 compressor intake pressure circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Turbocharger 1 compressor intake pressure circuit - voltage high (shorted to a high source)
Cummins 742Turbocharger 1 compressor intake pressure circuit: Voltage low / shorted low
Same failure as 692 on the turbocharger 1 compressor intake pressure circuit: the same fault condition as 692, reported for this part. The compressor inlet pressure sensor reads pressure before the compressor, so a clogged air filter or intake restriction shows up here first.· Shorted lowShorted lowCheck soonCauses
- Same causes as 692, applied to the turbocharger 1 compressor intake pressure circuit
- Wiring or connector problem local to the turbocharger 1 compressor intake pressure circuit
Checks
- 1Check the air filter restriction and the intake piping for collapse or blockage.
- 2Work through the checks listed for 692, starting at the turbocharger 1 compressor intake pressure circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Turbocharger 1 compressor intake pressure circuit - voltage low (shorted to a low source)
Turbocharger 1 compressor intake pressure2 codes
Cummins 743Turbocharger 1 compressor intake pressure: Erratic reading
Same failure as 686 on the turbocharger 1 compressor intake pressure: the same fault condition as 686, reported for this part. The compressor inlet pressure sensor reads pressure before the compressor, so a clogged air filter or intake restriction shows up here first.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 686, applied to the turbocharger 1 compressor intake pressure
- Wiring or connector problem local to the turbocharger 1 compressor intake pressure
Checks
- 1Check the air filter restriction and the intake piping for collapse or blockage.
- 2Work through the checks listed for 686, starting at the turbocharger 1 compressor intake pressure and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Turbocharger 1 compressor intake pressure - data erratic or incorrect
Cummins 3348Turbocharger 1 compressor intake pressure: Below normal· most severe
Same failure as 687 on the turbocharger 1 compressor intake pressure: the same fault condition as 687, reported for this part. The compressor inlet pressure sensor reads pressure before the compressor, so a clogged air filter or intake restriction shows up here first.· Real conditionReal conditionCheck soonCauses
- Same causes as 687, applied to the turbocharger 1 compressor intake pressure
- Wiring or connector problem local to the turbocharger 1 compressor intake pressure
Checks
- 1Check the air filter restriction and the intake piping for collapse or blockage.
- 2Work through the checks listed for 687, starting at the turbocharger 1 compressor intake pressure and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger 1 compressor intake pressure - below normal - most severe
Turbocharger turbine intake temperature2 codes
Cummins 2346Turbocharger turbine intake temperature: Above normal· least severe
Same failure as 2288 on the turbocharger turbine intake temperature: the same fault condition as 2288, reported for this part. The turbine intake temperature is the exhaust temperature entering the turbo, which the ECM watches to protect the turbo and exhaust parts.· Real conditionReal conditionInfoCauses
- Same causes as 2288, applied to the turbocharger turbine intake temperature
- Wiring or connector problem local to the turbocharger turbine intake temperature
Checks
- 1Look for a real cause of high exhaust heat, such as an overloaded engine or an air supply restriction.
- 2Work through the checks listed for 2288, starting at the turbocharger turbine intake temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger turbine intake temperature - above normal - least severe
Cummins 2451Turbocharger turbine intake temperature: Above normal· moderately severe
Same failure as 2288 on the turbocharger turbine intake temperature: the same fault condition as 2288, reported for this part. The turbine intake temperature is the exhaust temperature entering the turbo, which the ECM watches to protect the turbo and exhaust parts.· Real conditionReal conditionCheck soonCauses
- Same causes as 2288, applied to the turbocharger turbine intake temperature
- Wiring or connector problem local to the turbocharger turbine intake temperature
Checks
- 1Look for a real cause of high exhaust heat, such as an overloaded engine or an air supply restriction.
- 2Work through the checks listed for 2288, starting at the turbocharger turbine intake temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger turbine intake temperature - above normal - moderately severe
Turbocharger compressor outlet temperature (calculated)1 code
Cummins 2347Turbocharger compressor outlet temperature (calculated): Above normal· least severe
Same failure as 2288 on the turbocharger compressor outlet temperature: the same fault condition as 2288, reported for this part. This is a calculated value, not a measured one: the ECM works out compressor outlet temperature from the inlet and boost readings, so a code here points at those inputs.· Real conditionReal conditionInfoCauses
- Same causes as 2288, applied to the turbocharger compressor outlet temperature
- Wiring or connector problem local to the turbocharger compressor outlet temperature
Checks
- 1Check the compressor inlet temperature and boost sensors, which this value is calculated from.
- 2Work through the checks listed for 2288, starting at the turbocharger compressor outlet temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Turbocharger compressor outlet temperature (calculated) - above normal - least severe
Engine turbocharger 1 speed1 code
Cummins 5943Engine turbocharger 1 speed: Mechanical fault or not responding
The ECM commands the engine turbocharger 1 speed but sees no matching response, so it reports a mechanical fault or a part that is not responding even though the wiring may be fine.· Part or controllerPart or controllerCheck soonCauses
- Engine turbocharger 1 speed stuck, seized or restricted by dirt, soot or wear
- Electrical supply too weak to move the part
- Mechanical linkage or return spring broken
Checks
- 1Command the engine turbocharger 1 speed with the service tool and watch or listen for it to move
- 2Remove the engine turbocharger 1 speed and inspect it for sticking, wear, carbon or debris
- 3Check supply voltage and ground at the engine turbocharger 1 speed while it is commanded
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Turbocharger 1 compressor intake temperature sensor1 code
Cummins 7861Turbocharger 1 compressor intake temperature sensor: Abnormal rate of change
The turbocharger 1 compressor intake temperature sensor changed faster than it physically could, so the ECM treats the reading as a sensor or wiring problem and not as a real change.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent contact in the harness or connector of the turbocharger 1 compressor intake temperature sensor
- Failing part giving unstable output
- Poor ground or noisy supply feeding the circuit
Checks
- 1Log the turbocharger 1 compressor intake temperature sensor while moving the harness and connector, and look for steps instead of smooth changes
- 2Inspect the turbocharger 1 compressor intake temperature sensor connector for water, corrosion and loose pins
- 3Check the supply and ground at the turbocharger 1 compressor intake temperature sensor while the engine runs
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Check the turbo shaft for play and the compressor wheel for damage before anything else
- 2Check the air filter restriction and inlet piping for collapse before testing the sensor
- 3Check the air filter, charge-air cooler and cooling fan for restriction or poor airflow
- 4Inspect the sensor and its connector for heat damage and oil
- 5Compare the inlet pressure with barometric pressure at key on, engine off
- 6Review related temperature and pressure codes, because the calculation depends on them
- 7Watch turbo speed live while running the VGT actuator test; speed should rise smoothly with boost
Causes
- Speed sensor air gap changed or sensor damaged
- Restricted air filter or inlet piping making the inlet pressure genuinely low
- Restricted air filter or charge-air cooler raising compressor outlet temperature
- Harness chafed or corroded at the turbo connector
Most common here: real condition (8 of 17)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The ECM limits boost and torque to keep the turbo safe, so the engine feels weak under load.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
- Cummins ISX15 (2010-2012) Fault Code List (Diesel Repair)
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
- Cummins ISB6.7 (2013-2018) Fault Code List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
