Bobcat · Hydraulics
Bobcat Hydraulic oil and case drain temperatures fault codes
Temperature sensors on the hydraulic oil, the drive motor case drain and the pump case drain watch for overheating hydrostatic components. Codes are out of range high or low for the sensor, no communication from the sensor module, or genuine high, extremely high or reduced-performance temperatures.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes VSE001-00 to M0722 are all about the hydraulic oil and case drain temperatures. The most common failure type is lost message (5 of 25); 6 need an immediate stop. Start with this check: check hydraulic oil level and condition, then clean the cooler and radiator fins.
How urgent are they?
6 of 25 codes here mean stop now; the other 19 can wait until the shift ends, but find the cause before the next one.
- Stop now6
- Check soon19
What should I check first?
Check hydraulic oil level and condition, then clean the cooler and radiator fins.
Shared checks25 of 25
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat VSE001-00Oil temp. sensor, signal above normal range
The oil temp. sensor signal is above its normal range. The controller treats the reading as unreliable until it is back inside the window.· Real conditionReal conditionCheck soonCauses
- Sensor reading real high temperature or pressure
- Sensor drift or failure
- Signal wire shorted to supply
Checks
- 1Compare the oil temp. sensor reading with a separate gauge or probe
- 2Check the sensor wiring for shorts to supply
- 3Replace the sensor if the real value is normal but the reading stays high
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat VSE001-03Oil temp. sensor, voltage above normal
The signal voltage from the oil temp. sensor is above the normal range. That usually means a signal wire shorted to supply, an open ground or a failed sensor.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to a supply wire
- Open sensor ground
- Sensor failed
Checks
- 1Check the sensor ground at the oil temp. sensor plug and its continuity back to the controller
- 2Test the signal wire for voltage with the plug off
- 3Swap in a known good sensor to see if the reading moves back into range
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat VSE001-04Oil temp. sensor, voltage below normal
The signal voltage from the oil temp. sensor is below the normal range. That usually means a short to ground, a missing sensor supply or a failed sensor.· Shorted lowShorted lowCheck soonCauses
- Sensor wire shorted to ground
- Open sensor supply or ground
- Sensor failed
Checks
- 1Check the 5 V supply and ground at the oil temp. sensor plug with the key on
- 2Test the signal wire to ground with the plug off
- 3Compare the reading with a known good sensor or the same input on a matching machine
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat 07-10Hydraulic oil temperature high
Hydraulic oil is running hot. Ease off the work and let the machine cool while you look for the cause.· OtherOtherCheck soonCauses
- Hot ambient with heavy continuous load
- Hydraulic oil cooler clogged with dirt or debris
- Low hydraulic oil level
- Cooler fan not turning or belt slipping
Checks
- 1Check the hydraulic oil level at the sight gauge and top up with the correct fluid
- 2Check for a stuck-open relief or a worn pump that heats the oil by leaking internally
- 3Compare the temperature reading with an infrared thermometer on the reservoir; a big difference points at the sensor
- 4Clear the oil cooler core and radiator fins of dirt and chaff; a blocked cooler is the usual cause on a hot day
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 07-11Hydraulic oil temperature extremely high
The hydraulic oil temperature is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 07-15Hydraulic oil temperature shutdown level
Engine stopped due to excess hydraulic oil temperature. The engine will not run until the oil cools.· OtherOtherStop nowCauses
- Continuous relief valve operation
- Blocked oil cooler
- Fan or belt not working
Checks
- 1Allow the oil to cool and then check the oil level and the oil condition before restarting
- 2Check that nothing in the machine is stuck in relief, such as a joystick or auxiliary handle left held
- 3Check the sensor wiring for a short or poor ground that could fake a high temperature
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 07-21Hydraulic oil temperature out of range high
The hydraulic oil temperature signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the hydraulic oil temperature for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 07-22Hydraulic oil temperature out of range low
The hydraulic oil temperature signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the hydraulic oil temperature plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat U10A0-08Drive motor case drain hydraulic oil temperature sensor no communication
The controller cannot talk to the drive motor case drain hydraulic oil temperature sensor. Messages are missing on the CAN network, so the part or controller may not work properly.· Lost messageLost messageCheck soonCauses
- Loose or corroded CAN connector
- CAN wire broken or shorted
- Device without power or damaged
Checks
- 1Check the supply and ground at the drive motor case drain hydraulic oil temperature sensor plug
- 2Check the CAN wires for continuity and for shorts to each other
- 3Reseat the connectors and cycle the key to see if communication returns
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat C10A0-16Drive motor case drain hydraulic oil temperature out of range low
The drive motor case drain hydraulic oil temperature signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the drive motor case drain hydraulic oil temperature plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A0-17Drive motor case drain hydraulic oil temperature out of range high
The drive motor case drain hydraulic oil temperature signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the drive motor case drain hydraulic oil temperature for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A1-FADrive motor case drain hydraulic oil temperature high
The drive motor case drain hydraulic oil temperature reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the drive motor case drain hydraulic oil temperature belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat C10A1-FBDrive motor case drain hydraulic oil temperature extremely high
The drive motor case drain hydraulic oil temperature is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A1-FCDrive motor case drain hydraulic oil temperature reduced performance
The controller reports a performance problem on the drive motor case drain hydraulic oil temperature, such as reduced response, wrong direction, uncommanded motion or a position that cannot be reached.· OtherOtherCheck soonCauses
- Worn or sticking part
- Low supply voltage or poor ground
- Calibration out of date
Checks
- 1Check the drive motor case drain hydraulic oil temperature moves freely and without binding
- 2Check supply voltage and ground at its plug
- 3Recalibrate if the manual allows and retest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat U10A5-08Pump case drain hydraulic oil temperature sensor no communication
The controller cannot talk to the pump case drain hydraulic oil temperature sensor. Messages are missing on the CAN network, so the part or controller may not work properly.· Lost messageLost messageCheck soonCauses
- Loose or corroded CAN connector
- CAN wire broken or shorted
- Device without power or damaged
Checks
- 1Check the supply and ground at the pump case drain hydraulic oil temperature sensor plug
- 2Check the CAN wires for continuity and for shorts to each other
- 3Reseat the connectors and cycle the key to see if communication returns
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat C10A5-16Pump case drain hydraulic oil temperature out of range low
The pump case drain hydraulic oil temperature signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the pump case drain hydraulic oil temperature plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A5-17Pump case drain hydraulic oil temperature out of range high
The pump case drain hydraulic oil temperature signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the pump case drain hydraulic oil temperature for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A6-FAPump case drain hydraulic oil temperature high
The pump case drain hydraulic oil temperature reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the pump case drain hydraulic oil temperature belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat C10A6-FBPump case drain hydraulic oil temperature extremely high
The pump case drain hydraulic oil temperature is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat C10A6-FCPump case drain hydraulic oil temperature high
The pump case drain hydraulic oil temperature reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the pump case drain hydraulic oil temperature belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M0710Hydraulic oil temperature too high
Hydraulic oil is running hotter than normal. Ease off the work and let the machine cool while you look for the cause.· Real conditionReal conditionCheck soonCauses
- Cooler fan not turning or belt slipping
- Relief valve working constantly because of a stuck function
- Hot ambient with heavy continuous load
- Low hydraulic oil level
Checks
- 1Check that the cooling fan turns freely and that the drive belt is tight and not glazed
- 2Look for a function that keeps blowing over relief, such as a held auxiliary control or an attachment under constant load
- 3Check the oil condition; old oil or the wrong viscosity raises operating temperature
- 4Run the machine for a few minutes at idle and watch how fast the temperature falls to see whether the cooler flow is normal
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0711Hydraulic oil temperature extremely high
Hydraulic oil is dangerously hot. Stop working and let it cool before it reaches shutdown.· OtherOtherStop nowCauses
- Worn pump heating the oil internally
- Low oil level
- Cooler fan failure
Checks
- 1Check the oil level and the condition of the oil, and look for foam or a burnt smell
- 2Inspect the oil cooler for blockage inside the core as well as outside; flush it if debris is found
- 3Verify the temperature with an external thermometer to confirm the sensor is reading correctly
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0715Hydraulic oil temperature shutdown
The controller stopped the engine due to excessive hydraulic oil temperature. The engine will not run until the oil cools.· OtherOtherStop nowCauses
- Continuous relief valve operation
- Fan or belt not working
- Oil level low
Checks
- 1Clean the cooler on both sides and check the fan belt tension and the fan shroud
- 2Check for oil leaks that lowered the level and reduced the cooling flow
- 3Verify the sensor reading against an external thermometer after the machine has cooled
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0721Hydraulic oil temperature out of range high
The oil temperature sensor reads above its electrical range, which usually means a wiring or sensor problem and not real heat.· OtherOtherCheck soonCauses
- Broken return or ground wire at the hydraulic oil temperature sensor
- Short to supply or to the oil temperature sensor supply from the controller on the signal wire at the hydraulic oil temperature sensor plug
- Oil film on the temperature sensor plug
Checks
- 1Look at the harness along the hydraulic reservoir and return line for chafing against a supply wire and for heat damage
- 2Disconnect the plug and probe the controller-side oil temperature sensor supply from the controller; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
- 3Check the sensor thread and plug for leaks; hot hydraulic oil softens the seal and lets oil into the connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0722Hydraulic oil temperature out of range low
The oil temperature sensor reads below its electrical range, pointing to an open or grounded circuit.· Shorted lowShorted lowCheck soonCauses
- Loose or unplugged hydraulic oil temperature sensor connector
- Lost oil temperature sensor supply from the controller at the hydraulic oil temperature sensor, or a broken signal wire
- Signal wire grounded where the harness runs through the harness along the hydraulic reservoir and return line
Checks
- 1With the plug removed, a good hydraulic oil temperature sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the harness along the hydraulic reservoir and return line
- 2Look for green corrosion, pushed-back pins or a missing seal inside the hydraulic oil temperature sensor plug
- 3Measure the oil temperature sensor supply from the controller at the unplugged hydraulic oil temperature sensor connector with the key on; no voltage there means an open supply wire or a controller fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Check hydraulic oil level and condition, then clean the cooler and radiator fins.
- 2Confirm the cooling fan runs and the reversing cleaning cycle works.
- 3Compare the sensor reading with an infrared thermometer on the case drain line.
- 4Unplug the sensor and check connector and wiring continuity.
- 5A real case drain high temperature with clean coolers may mean a worn pump or motor needing dealer diagnosis.
Causes
- Cooler or radiator blocked, or fan not working
- Low hydraulic oil level
- Temperature sensor connector corroded or wiring open
- Worn pump or motor producing excess heat
Most common here: lost message (5 of 25)
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
When to stop
You'll notice: A hydraulic temperature warning shows and the machine may reduce drive performance to protect the hydrostatic system.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
- Bobcat S205 Operation & Maintenance Manual, service codes list
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
