Bobcat · Engine
Bobcat Fault Code 06‑13
Engine speed no signal
What does Bobcat code 06-13 mean?
No engine speed signal reaches the controller. The machine may crank but not start, or may stall. Urgency: check soon - the machine may derate or limit a function. Check first: check that the speed sensor is fully seated in its bore and the bracket bolt is tight; a loose sensor loses pulses.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check that the speed sensor is fully seated in its bore and the bracket bolt is tight; a loose sensor loses pulses
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Broken wire or loose pin in the sensor plug
- Wrong air gap or damaged tone wheel
- Failed speed sensor
- Engine speed sensor not fully seated
How it failed
You'll notice: The controller gets no engine speed pulse, so the machine may crank without starting or the tachometer will drop to zero while the engine is running.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine speed, ECU messages and power derate
- 06-10Engine speed highLost messageCheck soon
- 06-11Engine speed extremely highOtherStop now
- 06-13Engine speed no signalOtherCheck soon
- 06-15Engine speed shutdown levelReal conditionStop now
- 06-18Engine speed out of rangeOtherCheck soon
- M0610Engine speed too highReal conditionCheck soon
- M0611Engine speed extremely highReal conditionStop now
- M0613Engine speed no signalOtherCheck soon
- M0615Engine speed shutdownReal conditionStop now
Show the other 11 codesHide the other codes
- M0618Engine speed out of rangeOtherCheck soon
- M0634Engine speed invalid dataOtherCheck soon
- M4028Wrong ECU detectedOtherCheck soon
- M4228Wrong DCU detectedOtherCheck soon
- M6604ECU no communicationLost messageCheck soon
- M6904DCU no communicationLost messageCheck soon
- M8615Engine speed derate shutdownOtherStop now
- M8625Engine speed derate unresponsiveOtherCheck soon
- M8715Torque derate shutdownOtherStop now
- M8725Torque derate unresponsiveOtherCheck soon
- M9701Turbo prime sequence activeOtherInformation
Other Bobcat codes: Engine
- VPV004-05Fan control P/V (j), current below normal
- VSV004-05Reverse fan S/V (d), current below normal
- VPV004-06Fan control P/V (j), current above normal
- VSV004-06Reverse fan S/V (d), current above normal
- 04-09Engine oil pressure low
- 04-14Engine oil pressure extremely low
- 04-15Engine oil pressure shutdown level
Related on Equipments Finder
Source
Bobcat S205 Operation & Maintenance Manual, service codes list
This source lists 06-13 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Older Bobcat skid-steer and track loaders using the two-digit service codes (S205 manual, similar models).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
