Kubota · Engine ECU - SPN / FMI codes
Kubota Fault Code SPN157‑FMI4
Rail pressure sensor - open circuit or short to ground
What does Kubota code SPN157-FMI4 mean?
SPN 157 FMI 4 means the common-rail pressure sensor signal is below range. The ECU cannot trust rail pressure, so it limits the engine or shuts it down. Urgency: stop now - shut down and fix before working on. Check first: read rail pressure in Diagmaster with key on; a value near zero with the engine running points at the sensor.
- FMI 4
- Voltage below normal or shorted low
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Read rail pressure in Diagmaster with key on; a value near zero with the engine running points at the sensor
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Open rail pressure sensor signal wire
- Signal wire shorted to ground
- Failed rail pressure sensor
- Loose rail sensor connector
How it failed
You'll notice: Engine runs rough, derates or will not start, with the ECU lamp lit.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail, high-pressure fuel and suction control valve
1 other code on this part is also shorted low (SPN1347-FMI4). When they show together, start at the wiring and connector they share.
- SPN157-FMI0High rail pressureReal conditionStop now
- SPN157-FMI3Rail pressure sensor - short to batteryShorted highStop now
- SPN157-FMI4Rail pressure sensor - open circuit or short to groundShorted lowStop now
- SPN633-FMI7Pressure limiter opened in an emergencyPart or controllerStop now
- SPN679-FMI7Pressure limiter did not openPart or controllerStop now
- SPN679-FMI16Rail pressure failure after pressure limiter openedReal conditionStop now
- SPN1239-FMI1Fuel leaking in the high-pressure systemReal conditionStop now
- SPN1347-FMI3SCV (MPROP) - short to batteryShorted highStop now
- SPN1347-FMI4SCV (MPROP) drive system errorShorted lowStop now
Show the other 11 codesHide the other codes
- SPN1347-FMI5SCV (MPROP) - open circuitOpen circuitStop now
- SPN1347-FMI7SCV (MPROP) stuckPart or controllerStop now
- E:9101Fuel or rail pressure system errorOtherStop now
- E:9102SCV system errorOtherCheck soon
- E:9106Injector system errorLost messageStop now
- E:9120Fuel filter water warningOtherCheck soon
- E:9300Engine fuel system error (P/L)OtherStop now
- E:9301Engine fuel system error (rail pressure)OtherStop now
- E:9302Engine fuel system error (leakage)Lost messageStop now
- E:9303Engine fuel system error (SCV)OtherStop now
- E:9304Engine fuel system error (supply pump)OtherStop now
Other Kubota codes: Engine ECU - SPN / FMI codes
- SPN29-FMI3Accelerator position sensor 2 - short to battery
- SPN29-FMI4Accelerator position sensor 2 - ground short or open circuit
- SPN91-FMI2Accelerator position sensor correlation error
- SPN91-FMI3Accelerator position sensor 1 - short to battery
- SPN91-FMI4Accelerator position sensor 1 - ground short or open circuit
- SPN100-FMI1Engine oil pressure low
Related on Equipments Finder
Source
Kato Works - Kubota engine error codes (SPN / FMI table)
This source lists SPN157-FMI4 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota common-rail Tier 4 engines. The source lists the code under Kubota engines without naming machines (these engines power SVL/SSV loaders and KX/U excavators).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
