Kubota · Engine ECU system (E:91xx)
Kubota Fault Code E:9106
Injector system error
What does Kubota code E:9106 mean?
One or more injector circuits are open, shorted or not responding. The engine can misfire, run rough or stop completely. Urgency: stop now - shut down and fix before working on. Check first: check injector coil resistance for each cylinder against the manual value.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check injector coil resistance for each cylinder against the manual value
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Injector coil open or shorted
- Injector harness damaged under the valve cover
- Injector connector corroded
- Injector drive circuit failure in the ECU
How it failed
You'll notice: Engine misfire, rough idle or loss of power, with E:9106 and the ECU lamp.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail, high-pressure fuel and suction control valve
1 other code on this part is also lost message (E:9302). When they show together, start at the wiring and connector they share.
- SPN1347-FMI5SCV (MPROP) - open circuitOpen circuitStop now
- SPN1347-FMI7SCV (MPROP) stuckPart or controllerStop now
- E:9101Fuel or rail pressure system errorOtherStop now
- E:9102SCV system errorOtherCheck soon
- E:9106Injector system errorLost messageStop now
- E:9120Fuel filter water warningOtherCheck soon
- E:9300Engine fuel system error (P/L)OtherStop now
- E:9301Engine fuel system error (rail pressure)OtherStop now
- E:9302Engine fuel system error (leakage)Lost messageStop now
Show the other 11 codesHide the other codes
- SPN157-FMI0High rail pressureReal conditionStop now
- SPN157-FMI3Rail pressure sensor - short to batteryShorted highStop now
- SPN157-FMI4Rail pressure sensor - open circuit or short to groundShorted lowStop now
- SPN633-FMI7Pressure limiter opened in an emergencyPart or controllerStop now
- SPN679-FMI7Pressure limiter did not openPart or controllerStop now
- SPN679-FMI16Rail pressure failure after pressure limiter openedReal conditionStop now
- SPN1239-FMI1Fuel leaking in the high-pressure systemReal conditionStop now
- SPN1347-FMI3SCV (MPROP) - short to batteryShorted highStop now
- SPN1347-FMI4SCV (MPROP) drive system errorShorted lowStop now
- E:9303Engine fuel system error (SCV)OtherStop now
- E:9304Engine fuel system error (supply pump)OtherStop now
Other Kubota codes: Engine ECU system (E:91xx)
Related on Equipments Finder
Source
This source lists E:9106 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota SSV65, SSV75, SVL65-2, SVL75-3, SVL97-2 loaders (the models the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
