EF Logo

Volvo/Mack · MID 144 vehicle ECU

Volvo/Mack Vehicle speed sensor signal and supply fault codes

The vehicle speed sensor at the transmission output gives the vehicle ECU (MID 144) the road speed for the speedometer, cruise control and gear logic. The ECU also feeds the sensor its own supply voltage.

More about these parts

The signal codes (PID 84) cover a wrong or lost speed reading, and the supply codes (PPID 265) cover that supply being out of range.

FaultCheckMID 144PID 84FMI 2Volvo/Mack · Vehicle speed sensor signal and supply
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 144 PID 84 FMI 2 to MID 144 PPID 265 FMI 4 are all about the vehicle speed sensor signal and supply. The most common failure type is shorted low (2 of 5); none needs an immediate stop. Start with this check: inspect the sensor and tone ring for metal debris and damage.

How urgent are they?

None of the 5 codes here means stop now; all 5 can wait until the shift ends, but find the cause before the next one.

  • Check soon5

What should I check first?

Inspect the sensor and tone ring for metal debris and damage

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittent

    The vehicle speed signal from the speed sensor and the one from the ABS differ too much, or one of them is intermittent.· Erratic or implausible
    Check soon

    Causes

    • Vehicle speed sensor (VSS) harness damaged or rubbing at the transmission
    • Faulty VSS at the transmission output
    • Wrong K-factor (MG and MH parameters in the VECU) after a tyre, axle or transmission change
    • ABS speed message missing or inconsistent

    Checks

    1. 1Compare the speedometer, the ABS wheel speed and the speed in the scan tool on a test drive
    2. 2Check the VSS connector at the transmission for oil, corrosion and loose pins
    3. 3Wiggle the VSS harness while watching the speed signal for dropouts
    4. 4Verify the K-factor and tyre-size parameters match the rear axle ratio and tyres
    5. 5Check whether ABS codes are active, since a bad ABS speed message sets this too
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to ground

    The VECU sees low current on the vehicle speed sensor circuit, which means an open circuit or a sensor shorted to ground.· Open circuit
    Check soon

    Causes

    • VSS harness or connector open
    • VSS sensor open or shorted to ground
    • Damaged wire where the harness is clamped near the transmission

    Checks

    1. 1Read vehicle speed in the scan tool while driving; zero or erratic speed points at the circuit
    2. 2Unplug the VSS and measure the sensor coil resistance against the figure in the service manual
    3. 3Check continuity of both VSS wires from the connector to the VECU
    4. 4Check the signal wires for a short to ground with the key off
    5. 5Inspect the sensor tip and tone ring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 144 PID 84 FMI 6Vehicle speed sensor current high or shorted across sensor

    The VECU sees too much current in the vehicle speed sensor circuit, the signature of a short across the sensor or a grounded circuit.· Shorted low
    Check soon

    Causes

    • Short across the VSS sensor
    • VSS harness or connector pinched or wet
    • Faulty vehicle speed sensor

    Checks

    1. 1Look for a pinched VSS wire at brackets and cross-members
    2. 2Measure resistance across the sensor pins; a very low value points to the sensor
    3. 3Test each sensor wire for a short to chassis ground
    4. 4Check the connector for water and green corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 144 PPID 265 FMI 3Vehicle speed sensor supply too high

    The supply voltage for the vehicle speed sensor is above 9 V, so the VECU sees a short to a higher voltage in the VSS supply line.· Shorted high
    Check soon

    Causes

    • VSS supply wire touching a higher-voltage wire in the harness
    • Faulty vehicle speed sensor feeding voltage back into the supply
    • Damaged insulation at the transmission output bracket

    Checks

    1. 1Measure the VSS supply at the connector with the key on and compare it with the sensor reading
    2. 2Check the supply wire for contact with battery positive with the key off
    3. 3Unplug the VSS and see if the supply returns to normal
    4. 4Replace the sensor if the harness is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 144 PPID 265 FMI 4Vehicle speed sensor supply too low

    The supply voltage for the vehicle speed sensor is below 6.5 V, which the VECU treats as a short to ground or an overloaded supply.· Shorted low
    Check soon

    Causes

    • VSS supply wire shorted to ground against the transmission or frame
    • Sensor drawing too much current from a damaged coil
    • Water in the VSS connector pulling the supply down

    Checks

    1. 1Measure the VSS supply at the connector with the key on
    2. 2Check the supply wire for a short to ground with the key off
    3. 3Unplug the VSS and check whether the supply voltage recovers
    4. 4Dry and inspect the connector; replace the sensor if the harness is good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Inspect the sensor and tone ring for metal debris and damage
  2. 2Check the connector and harness at the transmission for damage, chafing against the housing and corrosion
  3. 3Measure the sensor resistance and compare it with the service data
  4. 4Unplug the sensor and measure whether the supply voltage returns to normal; if not, measure at the vehicle ECU pin
  5. 5Compare the vehicle speed with the ABS wheel speeds to see whether the sensor or the wiring is at fault

Causes

  • Sensor failed or contaminated with metal, or a damaged tone ring
  • Damaged wiring or a short in the supply wire
  • Connector corrosion or pushed-back pins at the sensor
  • Vehicle ECU output fault on the supply pin

Most common here: shorted low (2 of 5)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The speedometer reads wrongly or zero, cruise control does not work, and a check lamp comes on.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.