Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Fault Code MID 128 SID 22 FMI 3
Crankshaft position sensor signal missing
What does Volvo/Mack code MID 128 SID 22 FMI 3 mean?
The crankshaft position signal is missing, from an open, a short to battery or a short to ground in the CKP sensor circuit. The ECM cannot know engine speed or crank angle, which it needs for injection timing. Urgency: stop now - shut down and fix before working on. Check first: look at the crankshaft sensor connector near the flywheel housing for oil, heat and loose pins.
- MID 128
- Which control unit reports it
- SID 22
- Component at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Look at the crankshaft sensor connector near the flywheel housing for oil, heat and loose pins
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Open wire or connector fault on the CKP sensor circuit at the flywheel housing
- Short to battery or ground in the sensor wiring
- Failed crankshaft position sensor or a missing tone wheel signal
- Metal debris on the sensor tip
How it failed
You'll notice: The engine may crank but not start, or it loses power and stalls, with the MIL and yellow lamp lit.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Camshaft and crankshaft position sensors
1 other code on this part is also shorted high (MID 128 SID 21 FMI 3). When they show together, start at the wiring and connector they share.
- MID 128 SID 21 FMI 2Camshaft position sensor phase errorErratic or implausibleCheck soon
- MID 128 SID 21 FMI 3Camshaft position sensor signal missingShorted highCheck soon
- MID 128 SID 21 FMI 8Camshaft position sensor signal noisyErratic or implausibleCheck soon
- MID 128 SID 22 FMI 2Crankshaft position sensor intermittent or weak signalErratic or implausibleCheck soon
- MID 128 SID 22 FMI 3Crankshaft position sensor signal missingShorted highStop now
- MID 128 SID 22 FMI 8Crankshaft position sensor erratic signalErratic or implausibleCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - fuel, injectors and timing
- MID 128 SID 3 FMI 5Injector cylinder 3 circuit open or shorted
- MID 128 SID 4 FMI 5Injector cylinder 4 circuit open or shorted
- MID 128 SID 5 FMI 5Injector cylinder 5 circuit open or shorted
- MID 128 SID 6 FMI 5Injector cylinder 6 circuit open or shorted
- MID 128 SID 18 FMI 3Fuel actuator or valve control shorted high
- MID 128 SID 18 FMI 4Fuel actuator or valve control shorted low
Related on Equipments Finder
Source
This source lists MID 128 SID 22 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
