Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Fault Code MID 128 SID 22 FMI 2
Crankshaft position sensor intermittent or weak signal
What does Volvo/Mack code MID 128 SID 22 FMI 2 mean?
The crankshaft position sensor signal is intermittent or weak. The ECM relies on this signal for injection timing and engine speed. Urgency: check soon - the machine may derate or limit a function. Check first: check the sensor mounting, torque and air gap against the manual.
- MID 128
- Which control unit reports it
- SID 22
- Component at fault
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the sensor mounting, torque and air gap against the manual
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Faulty crankshaft sensor or damaged harness
- Sensor air gap wrong or tip dirty
- Damaged flywheel teeth or tone wheel
How it failed
You'll notice: MIL and yellow lamp lit; fuel consumption rises and cylinders can be unbalanced, with power loss and smoke.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Camshaft and crankshaft position sensors
3 other codes on this part are also erratic or implausible (MID 128 SID 21 FMI 2, MID 128 SID 21 FMI 8, MID 128 SID 22 FMI 8). When they show together, start at the wiring and connector they share.
- MID 128 SID 21 FMI 2Camshaft position sensor phase errorErratic or implausibleCheck soon
- MID 128 SID 21 FMI 3Camshaft position sensor signal missingShorted highCheck soon
- MID 128 SID 21 FMI 8Camshaft position sensor signal noisyErratic or implausibleCheck soon
- MID 128 SID 22 FMI 2Crankshaft position sensor intermittent or weak signalErratic or implausibleCheck soon
- MID 128 SID 22 FMI 3Crankshaft position sensor signal missingShorted highStop now
- MID 128 SID 22 FMI 8Crankshaft position sensor erratic signalErratic or implausibleCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - fuel, injectors and timing
- MID 128 SID 3 FMI 5Injector cylinder 3 circuit open or shorted
- MID 128 SID 4 FMI 5Injector cylinder 4 circuit open or shorted
- MID 128 SID 5 FMI 5Injector cylinder 5 circuit open or shorted
- MID 128 SID 6 FMI 5Injector cylinder 6 circuit open or shorted
- MID 128 SID 18 FMI 3Fuel actuator or valve control shorted high
- MID 128 SID 18 FMI 4Fuel actuator or valve control shorted low
Related on Equipments Finder
Source
This source lists MID 128 SID 22 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
