Volvo/Mack · MID 128 engine ECU - module, data link and power
Volvo/Mack Fault Code MID 128 PID 158 FMI 1
ECM battery voltage too low
What does Volvo/Mack code MID 128 PID 158 FMI 1 mean?
The battery voltage seen at the engine ECM is below the normal range. Mack lists the charging system, the battery or a poor ground as the causes. Urgency: check soon - the machine may derate or limit a function. Check first: measure battery voltage at rest and while cranking.
- MID 128
- Which control unit reports it
- PID 158
- Parameter at fault
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure battery voltage at rest and while cranking
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Weak or discharged batteries
- Charging system fault, such as a failed alternator
- Poor ground connection
- Corroded battery cables
How it failed
You'll notice: The starter may not crank and low voltage can set other codes on the engine and aftertreatment modules.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine ECU battery voltage
- MID 128 PID 158 FMI 1ECM battery voltage too lowReal conditionCheck soon
- MID 128 PID 158 FMI 3ECM battery voltage too highShorted highCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - module, data link and power
- MID 128 SID 39 FMI 3Starter relay output shorted high
- MID 128 SID 39 FMI 5Starter relay circuit open
- MID 128 PSID 161 FMI 2Vehicle identification number (VIN) missing
- MID 128 PSID 201 FMI 9Message from instrument cluster missing
- MID 128 PSID 229 FMI 2SAE J1939 data link 2 circuit shorted or open
- MID 128 PSID 229 FMI 9SAE J1939 data link 2 - lost communication with aftertreatment module
- MID 128 SID 231 FMI 2SAE J1939 data link (CAN 1) circuit fault
Related on Equipments Finder
Source
This source lists MID 128 PID 158 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
