Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake
Volvo/Mack Fault Code MID 128 PID 103 FMI 9
Turbocharger speed signal missing
What does Volvo/Mack code MID 128 PID 103 FMI 9 mean?
The ECM lost the turbocharger speed sensor signal entirely and logged an abnormal update rate. Without it the turbo cannot be monitored. Urgency: check soon - the machine may derate or limit a function. Check first: watch turbo speed live; it should rise with boost, and zero with the engine running confirms the loss.
- MID 128
- Which control unit reports it
- PID 103
- Parameter at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Watch turbo speed live; it should rise with boost, and zero with the engine running confirms the loss
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Turbocharger speed sensor failed or unplugged
- Open wire in the speed sensor harness
- Connector heat-damaged near the turbocharger
How it failed
You'll notice: Engine derates and the MIL comes on.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Other Volvo/Mack codes: MID 128 engine ECU - air, turbo, EGR and brake
- MID 128 SID 27 FMI 2Variable geometry turbo actuator - no valid command received
- MID 128 SID 27 FMI 4Variable geometry turbo actuator shorted to ground
- MID 128 SID 27 FMI 7Variable geometry turbo actuator mechanical fault
- MID 128 SID 27 FMI 9Variable geometry turbo actuator data missing for 2 seconds
- MID 128 SID 27 FMI 13Variable geometry turbo actuator self-calibration failed
- MID 128 PPID 35 FMI 0EGR mass flow too high
- MID 128 PPID 35 FMI 1EGR mass flow too low
- MID 128 PSID 98 FMI 0Turbocharger boost pressure too high
Related on Equipments Finder
Source
This source lists MID 128 PID 103 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
