Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 100 FMI 5
Engine oil pressure sensor circuit open or shorted to ground
What does Volvo/Mack code MID 128 PID 100 FMI 5 mean?
The ECM sees the oil pressure sensor circuit as open or pulled to ground. Urgency: check soon - the machine may derate or limit a function. Check first: read oil pressure live in the scan tool; a value stuck at zero with the engine running confirms the circuit fault.
- MID 128
- Which control unit reports it
- PID 100
- Parameter at fault
- FMI 5
- Current below normal or open circuit
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read oil pressure live in the scan tool; a value stuck at zero with the engine running confirms the circuit fault
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Open 5 V supply wire to the oil pressure sensor, often a broken strand near the connector
- Measuring wire chafed to ground against the block or a bracket
- Measuring wire broken or pin pushed back in the connector
- Engine oil pressure sensor failed open
How it failed
You'll notice: Yellow check lamp comes on and the cluster shows oil pressure as 0 while the engine runs normally, so you have no gauge to rely on.
Open circuitRead from FMI 5: current below normal or open circuit
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Oil pressure, oil level and oil temperature
2 other codes on this part are also open circuit (MID 128 PID 98 FMI 5, MID 128 PID 175 FMI 5). When they show together, start at the wiring and connector they share.
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to groundShorted lowCheck soon
- MID 128 PID 98 FMI 5Engine oil level sensor circuit openOpen circuitCheck soon
- MID 128 PID 100 FMI 1Engine oil pressure critically lowReal conditionStop now
- MID 128 PID 100 FMI 3Engine oil pressure sensor circuit shorted or ground openShorted highCheck soon
- MID 128 PID 100 FMI 5Engine oil pressure sensor circuit open or shorted to groundOpen circuitCheck soon
- MID 128 PID 100 FMI 13Engine oil pressure sensor out of calibrationPart or controllerCheck soon
- MID 128 PID 175 FMI 0Engine oil temperature critically highReal conditionStop now
- MID 128 PID 175 FMI 2Engine oil temperature signal erraticErratic or implausibleCheck soon
- MID 128 PID 175 FMI 4Engine oil temperature sensor shorted to groundShorted lowCheck soon
Show the other 3 codesHide the other codes
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
Related on Equipments Finder
Source
This source lists MID 128 PID 100 FMI 5 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
