Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 100 FMI 1
Engine oil pressure critically low
What does Volvo/Mack code MID 128 PID 100 FMI 1 mean?
The engine ECU measured oil pressure far below the range it expects for the current speed and load, and the reading is real, not a sensor fault. Urgency: stop now - shut down and fix before working on. Check first: stop the engine and check the dipstick on level ground before anything else; add oil only after finding where it went.
- MID 128
- Which control unit reports it
- PID 100
- Parameter at fault
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the engine and check the dipstick on level ground before anything else; add oil only after finding where it went
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Oil level far down from a leak at the filter housing, oil cooler, turbo oil lines or a rear main seal
- Oil pump worn or broken so it cannot build pressure at idle
- Oil galleries or filter restricted by sludge and neglected oil changes
- Oil diluted with fuel or too thin for the operating temperature, so pressure collapses when hot
How it failed
You'll notice: Red stop lamp comes on, the engine derates and may shut down if protection is enabled.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Oil pressure, oil level and oil temperature
3 other codes on this part are also real condition (MID 128 PID 98 FMI 1, MID 128 PID 175 FMI 0, MID 128 PID 175 FMI 16). When they show together, start at the wiring and connector they share.
- MID 128 PID 98 FMI 1Engine oil level critically lowReal conditionStop now
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to groundShorted lowCheck soon
- MID 128 PID 98 FMI 5Engine oil level sensor circuit openOpen circuitCheck soon
- MID 128 PID 100 FMI 1Engine oil pressure critically lowReal conditionStop now
- MID 128 PID 100 FMI 3Engine oil pressure sensor circuit shorted or ground openShorted highCheck soon
- MID 128 PID 100 FMI 5Engine oil pressure sensor circuit open or shorted to groundOpen circuitCheck soon
- MID 128 PID 100 FMI 13Engine oil pressure sensor out of calibrationPart or controllerCheck soon
- MID 128 PID 175 FMI 0Engine oil temperature critically highReal conditionStop now
- MID 128 PID 175 FMI 2Engine oil temperature signal erraticErratic or implausibleCheck soon
Show the other 3 codesHide the other codes
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
Related on Equipments Finder
Source
This source lists MID 128 PID 100 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
