Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack DPF soot level fault codes
The engine ECU estimates the soot in the DPF. When the level is high the truck needs a regeneration, and if it is ignored it needs a service regeneration.
Where to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
What do these codes mean?
Volvo/Mack codes MID 128 PPID 326 FMI 0 and MID 128 PPID 326 FMI 11 are all about the dPF soot level. Most are real condition faults; 1 needs an immediate stop. Start with this check: perform a parked or service regeneration.
How urgent are they?
1 of 2 codes here means stop now; the other 1 can wait until the shift ends, but find the cause before the next one.
- Stop now1
- Check soon1
What should I check first?
Perform a parked or service regeneration
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Volvo/Mack MID 128 PPID 326 FMI 0DPF soot level moderately high
The DPF system monitor reports a moderately high soot load. Mack lists a clogged DPF, a clogged hydrocarbon doser or regeneration being disabled.· Real conditionReal conditionCheck soonCauses
- Diesel particulate filter clogged
- Hydrocarbon doser (fuel injector) clogged
- Regeneration disabled by the driver or another component
Checks
- 1Check why regeneration did not run; look at the inhibit switch and regeneration history
- 2Check the doser fuel pressure and spray pattern
- 3Run a parked regeneration with the tool before you replace any parts
- 4Inspect the DPF for blockage when other checks pass
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Volvo/Mack MID 128 PPID 326 FMI 11DPF soot level critically high
The soot load in the DPF is critically high. Mack lists a clogged DPF, a hydrocarbon doser fault and regeneration being disabled.· Real conditionReal conditionStop nowCauses
- Diesel particulate filter clogged
- Aftertreatment hydrocarbon doser failure
- Regeneration disabled by the driver or another component
Checks
- 1Do not keep driving under load; arrange a service regeneration first
- 2Check the doser and its fuel pressure for damage, corrosion or looseness
- 3Check for other active codes that disable regeneration
- 4Inspect the DPF for blockage or a melted core
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Perform a parked or service regeneration
- 2Check the differential pressure sensor reading and its hoses, because a faulty sensor gives a false soot value
- 3Check for injector or EGR faults that make the engine produce more soot than normal and fill the filter
- 4Check the DPF condition by the pressure drop and, if needed, remove it for a visual and weight check
Causes
- Short trips and idling that prevent regeneration
- Faulty injection or EGR raising soot
- Pressure sensor fault
Most codes here: real condition (2 of 2)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The DPF lamp comes on and the engine derates if the level gets critical.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
