EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Crankcase pressure fault codes

The crankcase pressure sensor monitors blow-by in the crankcase ventilation system. High pressure points to worn rings or a blocked breather.

FaultStopMID 128PID 153FMI 0Volvo/Mack · Crankcase pressure
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 153 FMI 0 to MID 128 PID 153 FMI 7 are all about the crankcase pressure. 1 needs an immediate stop. Start with this check: inspect the crankcase ventilation filter and hoses.

How urgent are they?

1 of 4 codes here means stop now; the other 3 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon3

What should I check first?

Inspect the crankcase ventilation filter and hoses

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 153 FMI 0Crankcase pressure critically high

    Crankcase pressure is critically above range, which the Mack table puts down to piston ring blow-by.· Real condition
    Stop now

    Causes

    • Worn piston rings or liners causing blow-by
    • Crankcase ventilation breather blocked or frozen
    • Damaged turbocharger seal pushing pressure into the crankcase

    Checks

    1. 1Look for oil mist or smoke from the crankcase breather with the engine at idle
    2. 2Check the crankcase ventilation separator and hoses for blockage
    3. 3Check turbo shaft play and oil in the intake as a possible source
    4. 4Do a blow-by or cylinder leak-down test if the breather is clear
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 153 FMI 3Crankcase pressure sensor circuit shorted high

    The crankcase pressure sensor reads high from a short to positive on the measuring line or an open ground.· Shorted high
    Check soon

    Causes

    • Short to positive on the measuring line
    • Open ground to the sensor
    • Faulty crankcase pressure sensor

    Checks

    1. 1Check the sensor plug for 5 V supply and ground with the key on
    2. 2Test the signal wire for a short to a supply wire with the key off
    3. 3Check the ground wire continuity back to the ECM
    4. 4Replace the crankcase pressure sensor only after the harness checks out
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 153 FMI 5Crankcase pressure sensor circuit open

    The crankcase pressure sensor circuit is open in the 5 V supply, the measuring line or the ground, or the measuring line is shorted low.· Open circuit
    Check soon

    Causes

    • Open 5 V supply wire to the crankcase pressure sensor on the engine
    • Measuring wire shorted to ground in the breather area
    • Open measuring wire or a broken connector
    • Crankcase pressure sensor failed

    Checks

    1. 1Check the 5 V supply at the crankcase pressure sensor plug with the key on
    2. 2Test the signal wire for continuity and for a short to ground with the key off
    3. 3Inspect the connector pins for corrosion and oil
    4. 4Replace the sensor if the harness tests good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 153 FMI 7Crankcase ventilation leak detected

    A leak has been detected in the crankcase ventilation system.· Part or controller
    Check soon

    Causes

    • Faulty crankcase ventilation separator
    • Cracked or loose breather hoses
    • Leaking pipes or connections in the ventilation circuit

    Checks

    1. 1Inspect the breather separator and all ventilation hoses for cracks and loose clamps
    2. 2Check for oil leakage around the separator and hose connections
    3. 3Check the oil fill cap and dipstick seal for leaks
    4. 4Replace damaged hoses or the separator and recheck the live pressure
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Inspect the crankcase ventilation filter and hoses
  2. 2Check the sensor connector and wiring for corrosion, rubbing and pins that no longer grip
  3. 3Measure blow-by against the service limit
  4. 4Check the crankshaft and valve cover seals for fresh oil leaks that show high crankcase pressure

Causes

  • Blocked crankcase breather or separator
  • Worn piston rings with heavy blow-by
  • Sensor or harness fault

When to stop

You'll notice: The engine may smoke, leak oil from seals, and a stop or check lamp comes on.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.