Kubota · Engine ECU - SPN / FMI codes
Kubota Fault Code SPN110‑FMI0
Engine overheat - coolant temperature extremely high
What does Kubota code SPN110-FMI0 mean?
SPN 110 FMI 0 is a real or measured overheat: coolant temperature reached the most severe level. The ECU derates and may stop the engine to prevent damage. Urgency: stop now - shut down and fix before working on. Check first: stop the machine, idle without load and let the engine cool before opening the cap.
- SPN 110
- Engine coolant temperature
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the machine, idle without load and let the engine cool before opening the cap
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Low coolant or a leak
- Radiator or oil cooler blocked
- Fan, belt or water pump failure
- Thermostat stuck closed
How it failed
You'll notice: Overheat lamp and buzzer, power cuts back and the engine may shut down.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant, intake air temperature, oil pressure and overheat
3 other codes on this part are also real condition (SPN100-FMI1, SPN190-FMI0, E:9114). When they show together, start at the wiring and connector they share.
- SPN100-FMI1Engine oil pressure lowReal conditionStop now
- SPN110-FMI0Engine overheat - coolant temperature extremely highReal conditionStop now
- SPN110-FMI3Coolant temperature sensor - short to batteryShorted highCheck soon
- SPN110-FMI4Coolant temperature sensor - open circuit or short to groundShorted lowCheck soon
- SPN171-FMI3Intake air temperature sensor (built into MAF) - short to batteryShorted highCheck soon
- SPN171-FMI4Intake air temperature sensor (built into MAF) - open circuit or short to groundShorted lowCheck soon
- SPN172-FMI3Intake air temperature sensor - open circuit or short to batteryShorted highCheck soon
- SPN172-FMI4Intake air temperature sensor - open circuit or short to groundShorted lowCheck soon
- SPN190-FMI0Engine overrunReal conditionStop now
Show the other 6 codesHide the other codes
- E:9103Intake air temperature sensor system errorOtherCheck soon
- E:9104Coolant temperature system errorErratic or implausibleCheck soon
- E:9105Fuel temperature sensor system errorOtherCheck soon
- E:9114Pre-overheatReal conditionCheck soon
- E:9116Engine overheat warningShorted highStop now
- E:9118Engine oil pressure system errorOtherStop now
Other Kubota codes: Engine ECU - SPN / FMI codes
- SPN29-FMI3Accelerator position sensor 2 - short to battery
- SPN29-FMI4Accelerator position sensor 2 - ground short or open circuit
- SPN91-FMI2Accelerator position sensor correlation error
- SPN91-FMI3Accelerator position sensor 1 - short to battery
- SPN91-FMI4Accelerator position sensor 1 - ground short or open circuit
- SPN102-FMI3Boost pressure sensor - short to battery
Related on Equipments Finder
Source
Kato Works - Kubota engine error codes (SPN / FMI table)
This source lists SPN110-FMI0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota common-rail Tier 4 engines. The source lists the code under Kubota engines without naming machines (these engines power SVL/SSV loaders and KX/U excavators).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
