Kubota · Engine ECU - SPN / FMI codes
Kubota Fault Code SPN100‑FMI1
Engine oil pressure low
What does Kubota code SPN100-FMI1 mean?
SPN 100 FMI 1 means oil pressure dropped below the safe limit. Continuing to run can destroy the bearings, so stop the engine and find the cause. Urgency: stop now - shut down and fix before working on. Check first: shut the engine down at once and read the dipstick for level, colour and fuel smell.
- SPN 100
- Engine oil pressure
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Shut the engine down at once and read the dipstick for level, colour and fuel smell
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Engine oil level below the pickup tube
- Oil filter or strainer blocked by sludge
- Oil thinned by fuel dilution after repeated failed regenerations
- Worn main or rod bearings leaking oil pressure
How it failed
You'll notice: Oil pressure lamp and buzzer, with the ECU lamp lit; stop the engine at once.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant, intake air temperature, oil pressure and overheat
3 other codes on this part are also real condition (SPN110-FMI0, SPN190-FMI0, E:9114). When they show together, start at the wiring and connector they share.
- SPN100-FMI1Engine oil pressure lowReal conditionStop now
- SPN110-FMI0Engine overheat - coolant temperature extremely highReal conditionStop now
- SPN110-FMI3Coolant temperature sensor - short to batteryShorted highCheck soon
- SPN110-FMI4Coolant temperature sensor - open circuit or short to groundShorted lowCheck soon
- SPN171-FMI3Intake air temperature sensor (built into MAF) - short to batteryShorted highCheck soon
- SPN171-FMI4Intake air temperature sensor (built into MAF) - open circuit or short to groundShorted lowCheck soon
- SPN172-FMI3Intake air temperature sensor - open circuit or short to batteryShorted highCheck soon
- SPN172-FMI4Intake air temperature sensor - open circuit or short to groundShorted lowCheck soon
- SPN190-FMI0Engine overrunReal conditionStop now
Show the other 6 codesHide the other codes
- E:9103Intake air temperature sensor system errorOtherCheck soon
- E:9104Coolant temperature system errorErratic or implausibleCheck soon
- E:9105Fuel temperature sensor system errorOtherCheck soon
- E:9114Pre-overheatReal conditionCheck soon
- E:9116Engine overheat warningShorted highStop now
- E:9118Engine oil pressure system errorOtherStop now
Other Kubota codes: Engine ECU - SPN / FMI codes
- SPN29-FMI3Accelerator position sensor 2 - short to battery
- SPN29-FMI4Accelerator position sensor 2 - ground short or open circuit
- SPN91-FMI2Accelerator position sensor correlation error
- SPN91-FMI3Accelerator position sensor 1 - short to battery
- SPN91-FMI4Accelerator position sensor 1 - ground short or open circuit
- SPN102-FMI3Boost pressure sensor - short to battery
- SPN102-FMI4Boost pressure sensor - open circuit or short to ground
Related on Equipments Finder
Source
Kato Works - Kubota engine error codes (SPN / FMI table)
This source lists SPN100-FMI1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota common-rail Tier 4 engines. The source lists the code under Kubota engines without naming machines (these engines power SVL/SSV loaders and KX/U excavators).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
