EF Logo

Komatsu · Monitor user codes

Komatsu Operator user codes (E02, E03, E05, E10 and similar) fault codes

User codes are the short E-codes the monitor shows to the operator when a failure occurs. Each one groups several failure codes under a summary, for example E02 for the PC-EPC system or E10 for the engine controller.

More about these parts

The failure code behind it is read in service mode.

FaultCheckE0EKomatsu · Operator user codes (E02, E03, E05, E10 and similar)
Code shows hereFAULTE0E

Where this code shows

Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.

What do these codes mean?

Komatsu codes E0E to E15 are all about the operator user codes (E02, E03, E05, E10 and similar). None needs an immediate stop. Start with this check: read the failure codes behind the user code in service mode.

How urgent are they?

None of the 8 codes here means stop now; all 8 can wait until the shift ends, but find the cause before the next one.

  • Check soon8

What should I check first?

Read the failure codes behind the user code in service mode

Shared checks

8 of 8

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Komatsu E0ENetwork (data link) failure

    User code E0E points to a failure on the machine data link.· Lost message
    Check soon

    Causes

    • CAN or KOMNET data link wire open or shorted
    • Pump or engine controller without power or ground
    • Loose controller connector
    • Controller left on the wrong software after replacement

    Checks

    1. 1Read DA2RMC or CA1633 in service mode to see which controller is missing
    2. 2Check power and ground at the engine controller and the pump controller
    3. 3Measure the resistance across the CAN pair at a controller connector to check termination
    4. 4Inspect the controller connectors for water and pushed-back pins
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Komatsu E02PC-EPC system

    User code E02 means a fault in the PC-EPC system that sets the pump output.· Other
    Check soon

    Causes

    • PC-EPC solenoid coil open or shorted
    • Wire to the PC-EPC solenoid damaged
    • Pump controller output failed

    Checks

    1. 1Read the failure codes in service mode and note which PC-EPC code is active
    2. 2Measure the PC-EPC coil resistance and check the wires to the pump controller
    3. 3Inspect the PC-EPC connectors at the pump for water
    4. 4Compare with the other pump's coil to see which is out of range
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E03Swing parking brake system

    User code E03 means a fault in the swing parking brake system.· Other
    Check soon

    Causes

    • Swing brake solenoid coil open or shorted
    • Wire to the swing brake solenoid damaged
    • Swing brake stuck or not releasing

    Checks

    1. 1Read the failure codes in service mode to see whether DW45KA or DW45KB is active
    2. 2Measure the swing brake solenoid coil resistance and the wires to the pump controller
    3. 3Inspect the swing brake solenoid connector for water and corrosion
    4. 4Check that the brake releases when the swing is operated
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E05Governor motor system

    User code E05 means a fault in the governor motor system on machines that use a mechanical governor.· Other
    Check soon

    Causes

    • Governor motor failed
    • Feedback potentiometer or wiring fault
    • Linkage binding

    Checks

    1. 1Check the governor motor wiring and connector
    2. 2Check the linkage for binding
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E10Engine controller power or drive failure

    User code E10 points to a power failure or a drive circuit fault in the engine controller.· Other
    Check soon

    Causes

    • Engine controller supply or ground failure
    • Injector, IMV or speed sensor circuit fault behind it

    Checks

    1. 1Read the failure codes behind E10 in service mode
    2. 2Check controller supply and ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E11Engine control system failure, output limited

    User code E11 points to a failure in the engine control system.· Other
    Check soon

    Causes

    • Common rail pressure fault behind the user code
    • Injector or inlet metering valve circuit fault

    Checks

    1. 1Read the failure codes behind E11 in service mode
    2. 2Check rail pressure and injector circuits
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E14Feedback system failure (throttle circuit)

    User code E14 points to a feedback system failure, which the SINOCMP table ties to the throttle sensor circuit.· Other
    Check soon

    Causes

    • Throttle sensor or supply fault behind it
    • Fuel dial wiring damaged

    Checks

    1. 1Read the throttle codes behind E14 in service mode
    2. 2Check the fuel dial wiring
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu E15Engine sensor failure

    User code E15 points to an engine sensor fault such as temperature, fuel pressure or oil pressure, which reduces engine protection.· Other
    Check soon

    Causes

    • Coolant, intake temperature or oil pressure sensor fault
    • Sensor supply fault

    Checks

    1. 1Read the engine sensor codes behind E15 in service mode
    2. 2Check the sensor supplies
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Read the failure codes behind the user code in service mode
  2. 2Check battery voltage and connectors before replacing any part
  3. 3Fix the listed failure codes and then clear the fault history
  4. 4Confirm the user code does not come back after a restart

Causes

  • Any failure code in the matching system
  • Loose connectors or low battery supply upsetting a controller
  • Controller reset after a supply dip

When to stop

You'll notice: A user code appears on the monitor with the caution lamp or buzzer.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.