John Deere · Engine control unit (ECU) - PowerTech engine
John Deere Fault Code ECU 000100.01
Low engine oil pressure
What does John Deere code ECU 000100.01 mean?
The ECU sees engine oil pressure below the limit. The operator may see a low oil pressure warning, and running the engine on with real low pressure can destroy the bearings in minutes. Urgency: stop now - shut down and fix before working on. Check first: stop the engine at once and check the oil level and condition on the dipstick.
- ECU
- Which controller reports it
- 000100
- Engine oil pressure
- .01
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the engine at once and check the oil level and condition on the dipstick
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Engine oil level too low
- Oil diluted with fuel or coolant, or the wrong grade of oil
- Worn bearings or a weak oil pump
- Oil pressure sensor reading wrong or its wiring faulty
How it failed
You'll notice: The ECU sees engine oil pressure below its limit.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine oil pressure, boost, turbo, EGR and fuel rail
2 other codes on this part are also lost message (ECU 000157.17, ECU 002790.16). When they show together, start at the wiring and connector they share.
- ECU 000027.03EGR valve position signal highShorted highCheck soon
- ECU 000027.04EGR valve position signal lowShorted lowCheck soon
- ECU 000027.07EGR valve actuator faultOtherCheck soon
- ECU 000100.01Low engine oil pressureLost messageStop now
- ECU 000100.03Engine oil pressure input voltage highShorted highCheck soon
- ECU 000100.04Engine oil pressure signal voltage lowShorted lowCheck soon
- ECU 000100.18Engine power limited by oil pressureOtherCheck soon
- ECU 000100.31Oil pressure sensed with engine stoppedOtherCheck soon
- ECU 000102.02Manifold air pressure sensor troubleErratic or implausibleCheck soon
Show the other 15 codesHide the other codes
- ECU 000102.03Manifold air pressure sensor faultOtherCheck soon
- ECU 000102.04Manifold air pressure signal voltage lowShorted lowCheck soon
- ECU 000103.00Turbo speed too highShorted highCheck soon
- ECU 000103.05Turbocharger speed sensor lowOpen circuitCheck soon
- ECU 000103.06Turbocharger speed power highShort circuitCheck soon
- ECU 000103.08Turbocharger speed not validErratic or implausibleCheck soon
- ECU 000103.31Turbocharger speed missingOtherCheck soon
- ECU 000108.02Barometric pressure sensor invalidOtherCheck soon
- ECU 000157.04Fuel rail pressure sensor voltage faultOtherCheck soon
- ECU 000157.10Fuel rail pressure dropOtherCheck soon
- ECU 000157.17Fuel rail pressure does not riseLost messageCheck soon
- ECU 000611.03Injection circuit shortedOtherCheck soon
- ECU 000611.04Injection wiring burntShort circuitCheck soon
- ECU 001347.07Fuel filter and rail attentionOtherCheck soon
- ECU 002790.16Compressor outlet temperature highLost messageCheck soon
Related on Equipments Finder
Source
Inside the Yard - John Deere fault codes list (ECU engine codes)
This source lists ECU 000100.01 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere PowerTech engines; code list comes from tractor-based sources, confirm for your machine.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
