EF Logo

John Deere · Engine control unit (ECU) - Exhaust

John Deere Air filter, exhaust filter, fuel level and monitor sensors fault codes

This page covers items the operator can see on the monitor. The air cleaner differential pressure codes show a restricted air filter, and the exhaust filter codes show the filter needs cleaning or has a fault, including parked cleaning requests.

More about these parts

The fuel level sensor (B18) and the monitor internal temperature sensor have circuit codes.

FaultCheckECU 000107.00John Deere · Air filter, exhaust filter, fuel level and monitor sensors
Code shows hereFAULTECU 000107.00

Where this code shows

Turn the key on and open the monitor's diagnostic/fault screen.

What do these codes mean?

John Deere codes ECU 000107.00 to ICZ 20141.02 are all about the air filter, exhaust filter, fuel level and monitor sensors. The most common failure type is real condition (3 of 13); none needs an immediate stop. Start with this check: check the air filter and replace or clean it if dirty; check the dust valve and intake hoses.

How urgent are they?

None of the 13 codes here means stop now; 8 can wait until the shift ends, but find the cause before the next one; 5 are information only.

  • Check soon8
  • Info5

What should I check first?

Check the air filter and replace or clean it if dirty; check the dust valve and intake hoses

Shared checks

13 of 13

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • John Deere ECU 000107.00Air filter differential pressure high

    The engine ECU sees air filter restriction at the most severe level.· Real condition
    Check soon

    Causes

    • Air cleaner element clogged with dust, especially after work in dry or dusty ground
    • Dust cap or pre-cleaner packed so air cannot get in
    • Intake pipe collapsed or a hose soft on the suction side
    • Air filter restriction sensor or its wiring faulty

    Checks

    1. 1Take the air cleaner element out and look at it against a light; a dark clogged element confirms the cause
    2. 2Clean the pre-cleaner and dust cap and check the air intake pipe for collapse or kinks
    3. 3Fit a new element and see whether the code clears and full power returns
    4. 4Unplug the restriction sensor and check its wiring and connector for water
    5. 5Check the intake hoses and clamps for leaks on the engine side of the filter
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • John Deere ECU 003701.14Parked exhaust filter cleaning requested

    The ECU is asking for a parked exhaust filter cleaning because soot loading is high.· Lost message
    Info

    Causes

    • Soot loading high from short work cycles that prevent automatic regeneration
    • Regeneration interrupted by shutting the engine down
    • Parked regeneration not run when the lamp came on
    • An engine problem raising soot output

    Checks

    1. 1Park the machine outdoors away from anything that burns and start the parked regeneration
    2. 2Do not shut the engine down during the cleaning cycle
    3. 3Check for engine codes that point to a soot-producing fault
    4. 4Check the exhaust filter pressure sensor and hoses
    5. 5Ask the operator to avoid long idling periods
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere DSZ 13303.02Monitor internal temperature sensor abnormal

    The monitor reports that its built-in temperature sensor is not reading correctly.· Other
    Check soon

    Causes

    • Internal monitor temperature sensor failed
    • Monitor overheated in direct sun or a hot cab
    • Poor supply voltage to the monitor

    Checks

    1. 1Let the cab cool down and see whether the display recovers
    2. 2Check the supply voltage at the monitor connector with the key on
    3. 3Inspect the monitor connector for moisture and corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ICZ 13303.02Monitor internal temperature sensor abnormal

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Other
    Check soon

    Causes

    • Internal monitor temperature sensor failed
    • Monitor overheated in direct sun or a hot cab
    • Poor supply voltage to the monitor

    Checks

    1. 1Let the cab cool down and see whether the display recovers
    2. 2Check the supply voltage at the monitor connector with the key on
    3. 3Inspect the monitor connector for moisture and corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere DSZ 13311.03Fuel level sensor (B18) open circuit

    The fuel level sender (B18) reads as an open circuit, so the fuel gauge will show an incorrect level.· Open circuit
    Info

    Causes

    • Open B18 signal wire or an unplugged connector at the tank
    • Fuel sender float arm broken or stuck
    • Corroded sender ground

    Checks

    1. 1Unplug B18 and measure its resistance while moving the float arm through its travel
    2. 2Check the sender ground connection at the tank
    3. 3Check the signal wire continuity to the monitor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere ICZ 13311.03Fuel level sensor (B18) open circuit

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Open circuit
    Info

    Causes

    • Open B18 signal wire or an unplugged connector at the tank
    • Fuel sender float arm broken or stuck
    • Corroded sender ground

    Checks

    1. 1Unplug B18 and measure its resistance while moving the float arm through its travel
    2. 2Check the sender ground connection at the tank
    3. 3Check the signal wire continuity to the monitor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere DSZ 13311.04Fuel level sensor (B18) shorted to ground

    The fuel level sender (B18) reads as shorted to ground, so the fuel gauge will show an incorrect level, often empty.· Shorted low
    Info

    Causes

    • B18 signal wire shorted to ground
    • Sender failed shorted
    • Water in the sender connector

    Checks

    1. 1Unplug B18 and see whether the code changes to an open-circuit condition
    2. 2Check the signal wire for a short to ground with the monitor end disconnected
    3. 3Measure the sender resistance across its travel
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • John Deere ICZ 13311.04Fuel level sensor (B18) shorted to ground

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Shorted low
    Info

    Causes

    • B18 signal wire shorted to ground
    • Sender failed shorted
    • Water in the sender connector

    Checks

    1. 1Unplug B18 and see whether the code changes to an open-circuit condition
    2. 2Check the signal wire for a short to ground with the monitor end disconnected
    3. 3Measure the sender resistance across its travel
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • John Deere MCZ 20010.02Exhaust filter abnormal

    The exhaust filter alarm is raised, usually soot loading that regeneration has not cleared.· Other
    Check soon

    Causes

    • Soot loading too high because regeneration keeps being interrupted by short work cycles or by shutting down mid-clean
    • Engine running with an air or fuel fault that loads the filter faster than it can burn off
    • Exhaust filter differential pressure sensor or its hoses blocked or leaking
    • Filter itself blocked with ash and past its cleaning interval

    Checks

    1. 1Read the soot load and last regeneration on the monitor and run a parked regeneration if the machine allows one
    2. 2Check for engine ECU codes about air, fuel or exhaust pressure that may be loading the filter
    3. 3Inspect the filter pressure sensor lines for cracks, kinks and soot blockage
    4. 4Ask the operator whether the engine is being shut down while the regeneration lamp is lit
    5. 5Have the filter checked for ash if cleaning does not bring the soot load down
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere DSZ 20106.02Air cleaner restriction alarm

    The monitor raises the Air cleaner restriction alarm warning, which means the condition it watches on the air cleaner and air filter differential pressure is outside its normal state or the input to it is faulty.· Real condition
    Check soon

    Causes

    • The real condition the air cleaner and air filter differential pressure monitors is present
    • Switch or sensor of the air cleaner and air filter differential pressure failing or wired wrongly
    • Harness or connector fault between the input and the monitor

    Checks

    1. 1Confirm the real condition at the air cleaner and air filter differential pressure on the machine before replacing parts
    2. 2Check the switch or sensor plug and wiring for the air cleaner and air filter differential pressure
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • John Deere ECU 020106.02Air cleaner restriction alarm

    The monitor raises the Air cleaner restriction alarm warning, which means the condition it watches on the air cleaner and air filter differential pressure is outside its normal state or the input to it is faulty.· Real condition
    Check soon

    Causes

    • The real condition the air cleaner and air filter differential pressure monitors is present
    • Switch or sensor of the air cleaner and air filter differential pressure failing or wired wrongly
    • Harness or connector fault between the input and the monitor

    Checks

    1. 1Confirm the real condition at the air cleaner and air filter differential pressure on the machine before replacing parts
    2. 2Check the switch or sensor plug and wiring for the air cleaner and air filter differential pressure
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • John Deere ICZ 20137.02Exhaust filter alarm

    The monitor raises the Exhaust filter alarm warning, which means the condition it watches on the exhaust filter is outside its normal state or the input to it is faulty.· Other
    Check soon

    Causes

    • The real condition the exhaust filter monitors is present
    • Switch or sensor of the exhaust filter failing or wired wrongly
    • Harness or connector fault between the input and the monitor

    Checks

    1. 1Confirm the real condition at the exhaust filter on the machine before replacing parts
    2. 2Check the switch or sensor plug and wiring for the exhaust filter
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ICZ 20141.02Exhaust temperature alarm

    The monitor raises the Exhaust temperature alarm warning, which means the condition it watches on the exhaust filter is outside its normal state or the input to it is faulty.· Other
    Check soon

    Causes

    • The real condition the exhaust filter monitors is present
    • Switch or sensor of the exhaust filter failing or wired wrongly
    • Harness or connector fault between the input and the monitor

    Checks

    1. 1Confirm the real condition at the exhaust filter on the machine before replacing parts
    2. 2Check the switch or sensor plug and wiring for the exhaust filter
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the air filter and replace or clean it if dirty; check the dust valve and intake hoses
  2. 2For exhaust filter codes perform the cleaning the monitor asks for, parked or stationary as required
  3. 3For the fuel level sensor measure the sender resistance at several fuel levels and check its wire
  4. 4Check the sensor hose and plug for the pressure sensor behind a filter code
  5. 5Clear the code after the repair and run the machine to see if it returns

Causes

  • Air or exhaust filter really restricted by dust or soot
  • Differential pressure sensor hose blocked or plug corroded
  • Fuel level sender or wire open or shorted to ground
  • Operator ignored a cleaning request until the filter loaded further

Most common here: real condition (3 of 13)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The engine may lose power or derate with a restricted air or exhaust filter; a fuel level or monitor temperature fault gives a wrong gauge or display only.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.