JLG · Outputs (valves and coils)
JLG Fault Code 331
Brake - short to battery
What does JLG code 331 mean?
The controller reads battery voltage on the brake output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it. Urgency: stop now - shut down and fix before working on. Check first: pull the plug on the drive manifold at the chassis, key on, and check the output wire for voltage; if it stays with the load off, suspect the module.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Pull the plug on the drive manifold at the chassis, key on, and check the output wire for voltage; if it stays with the load off, suspect the module
Then 3 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 4 done
Causes
- Supply leaking onto the output wire through damaged insulation
- Brake output touched by a supply wire in the drive harness, so the brake is told to release when it should be held
- Supply wire pinched against the output wire along the chassis frame rails near the drive motors, where heat and road debris wear the sheathing
- Crushed pin touching a live neighbour; the brake valve plug sits low on the drive manifold and collects wash water and road spray
How it failed
You'll notice: The wheels do not turn when the drive joystick is moved, even though the engine runs and the pump makes flow.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Drive brake, traction lock, oscillating axle and dump valves
4 other codes on this part are also shorted high (3360, 3367, 33420, 33423). When they show together, start at the wiring and connector they share.
- 3-5Brake pressure problemOtherCheck soon
- 331Brake - short to batteryShorted highStop now
- 332Brake - open circuitOpen circuitStop now
- 3358Main Dump Valve - short to groundShorted lowStop now
- 3359Main Dump Valve - open circuitOpen circuitStop now
- 3360Main Dump Valve - short to batteryShorted highStop now
- 3361Brake - short to groundShorted lowStop now
- 3365Steer Dump Valve - short to groundShorted lowStop now
- 3366Steer Dump Valve - open circuitOpen circuitStop now
Show the other 7 codesHide the other codes
- 3367Steer Dump Valve - short to batteryShorted highStop now
- 8669Oscillating axle switch disagreementOtherCheck soon
- 33420Traction Lock Valve - short to batteryShorted highCheck soon
- 33421Traction Lock Valve - open circuitOpen circuitCheck soon
- 33422Traction Lock Valve - short to groundShorted lowCheck soon
- 33423Oscillating Axle Valves - short to batteryShorted highCheck soon
- 33424Oscillating Axle Valves - short to groundShorted lowCheck soon
Other JLG codes: Outputs (valves and coils)
Related on Equipments Finder
Source
JLG 600S/660SJ Service and Maintenance Manual 3121298, section 6 (Table 6-8 Fault Code List)
This source lists 331 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG 600S, 600SJ, 660SJ with newer module software; same DTC scheme on other JLG Control System booms, confirm in your manual.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
