JLG · Platform / ground controls
JLG Fault Code 2‑1
Footswitch or keyswitch fault
What does JLG code 2-1 mean?
The controller sees the two footswitch contacts reading the same state for over a second, or the keyswitch input is invalid. Platform functions are blocked until it is cleared; a footswitch fault needs the red EMS button recycled. Urgency: check soon - the machine may derate or limit a function. Check first: read the Help message on the analyzer: FSW FAULTY or KEYSWITCH FAULTY.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the Help message on the analyzer: FSW FAULTY or KEYSWITCH FAULTY
Then 4 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 5 done
Causes
- Footswitch with one contact stuck or worn so both channels agree
- Broken or pinched footswitch cable inside the platform control box
- Corroded platform module connector at the footswitch input
- Keyswitch contacts worn or key left between positions
1 more causeFewer causes
- Platform module input damaged (rare)
How it failed
You'll notice: The platform controls go dead: nothing moves from the basket, and the fault lamp flashes 2-1 at the ground station.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Footswitch, joysticks, steer switches and start sequence
3 other codes on this part are also real condition (227, 234, 2211). When they show together, start at the wiring and connector they share.
- 2-1Footswitch or keyswitch faultReal conditionCheck soon
- 2-2Drive or steer selection faultOtherCheck soon
- 2-3Boom function selection faultOtherCheck soon
- 2-4Steering digital inputs faultyOtherCheck soon
- 2-7Accelerator input faultyOtherCheck soon
- 0011Footswitch openOtherInformation
- 213Footswitch faultyOtherCheck soon
- 224Function problem - steer left permanently selectedOtherCheck soon
- 225Function problem - steer right permanently selectedOtherCheck soon
Show the other 17 codesHide the other codes
- 227Steer switches faultyReal conditionCheck soon
- 234Function switches faulty - check diagnostics/boomReal conditionCheck soon
- 235Function switches locked - selected before aux powerOtherCheck soon
- 236Function switches locked - selected before start switchOtherCheck soon
- 237Start switch locked - selected before keyswitchOtherCheck soon
- 2211Footswitch interlock trippedReal conditionCheck soon
- 2212Drive locked - joystick moved before footswitchOtherCheck soon
- 2213Steer locked - selected before footswitchOtherCheck soon
- 2216Drive/steer joystick out of range highShorted highCheck soon
- 2217Drive/steer joystick centre tap badOtherCheck soon
- 2219Lift/swing joystick out of range highOtherCheck soon
- 2220Lift/swing joystick centre tap badOtherCheck soon
- 2221Lift/swing locked - joystick moved before footswitchOtherCheck soon
- 2222Waiting for footswitch to be openOtherInformation
- 2223Function switches locked - selected before enableOtherCheck soon
- 2224Footswitch selected before startOtherCheck soon
- 2310Function problem - ground enable permanently selectedOtherCheck soon
Other JLG codes: Platform / ground controls
Related on Equipments Finder
Source
JLG 600S/600SJ/660SJ/600A/AJ Service and Maintenance Manual 3120840, section 6 (Tables 6-3, 6-5)
This source lists 2-1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG boom lifts with the JLG Control System (600S, 600SJ, 660SJ, 600A/AJ, 450A, 510A, 400S, 1200/1350SJP families).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
