JCB · Engine ECU (Dieselmax / Ecomax) - electrical
JCB System voltage, charging, warning lamps and service interval fault codes
The controllers watch battery and alternator voltage. These codes report a system voltage that is too low, too high or a charging fault.
More about these partsLess
The ECU drives the engine warning, test and DPF lamps on the cluster. These codes report a fault in those lamp circuits. The controller counts hours and warns when a service is due. It is monitored by the controller for the service interval counter.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes B130A to P1669 are all about the system voltage, charging, warning lamps and service interval. The most common failure type is shorted high (3 of 13); none needs an immediate stop. Start with this check: measure battery voltage engine off and at fast idle, charging should be higher.
How urgent are they?
None of the 13 codes here means stop now; 8 can wait until the shift ends, but find the cause before the next one; 5 are information only.
- Check soon8
- Info5
What should I check first?
Measure battery voltage engine off and at fast idle, charging should be higher
Shared checks13 of 13
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB B130ASupplementary service interval due / elapsed
A supplementary service interval, such as a separate item on the schedule, has been reached or has passed. The operator sees a reminder on the display, which is a prompt only and does not stop the machine.· OtherOtherInfoCauses
- Hours reached the interval for the extra item, such as a second fluid or filter change
- Item serviced but its counter not reset
- Counter programmed with a different interval from the manual
Checks
- 1Check which supplementary item is due in the service schedule for the machine
- 2Carry out that service item and record it in the service log
- 3Reset the supplementary interval separately from the main service interval
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0560System voltage fault
System voltage fault. The controller logged a fault on the system voltage, which affects how the battery and charging system works until the cause is found.· OtherOtherCheck soonCauses
- System voltage or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the system voltage and look for a value that is stuck or implausible
- 2Check the system voltage connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0562System voltage low
Supply voltage reaching the engine ECU fell below about 10 to 11.5 V while the engine was running. Expect warning lights, erratic gauges, hard starting or the ECU resetting.· Shorted lowShorted lowCheck soonCauses
- Weak or old battery that cannot hold voltage under load
- Alternator not charging, or a slipping belt
- Loose or corroded battery terminals or earth strap
- High resistance in the main supply to the ECU, such as a poor ignition feed
- Heavy electrical load or a short pulling the system down
Checks
- 1Measure battery voltage with the engine off and again at fast idle
- 2Check the alternator output and the drive belt condition and tension
- 3Clean and tighten both battery terminals and the main earth straps
- 4Voltage-drop test the ECU supply and ground while cranking
- 5Load test the battery and look for dead cells
- 6Check for a parasitic drain or a repeated fault on other electrical circuits
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P0563System voltage high
System voltage went above about 15.5 V, which means the charging system is overcharging. It can damage the battery and electronics and may make the ECU log other voltage-related faults.· Shorted highShorted highCheck soonCauses
- Alternator regulator failed and allowing too high output
- Poor sensing or earth connection at the alternator that makes the regulator overcompensate
- Loose or corroded battery connection giving a misreading at the ECU
- Wrong or failing battery that cannot take charge
- Wiring fault between the alternator and the ECU supply
Checks
- 1Measure the battery voltage with the engine running at a steady speed and see if it is above the limit
- 2Check the alternator output at the terminal and compare it with the battery voltage
- 3Check the alternator earth and sensing wire are tight and clean
- 4Inspect both battery clamps for corrosion and a loose fit
- 5Check battery water level and smell for sulphur, which means it is overcharging
- 6Replace the alternator only after the wiring checks pass
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P0650Malfunction indicator lamp control circuit fault
Malfunction indicator lamp control circuit fault. The controller logged a fault on the malfunction indicator lamp control circuit, which affects how the warning lamp circuit works until the cause is found.· OtherOtherInfoCauses
- Malfunction indicator lamp control circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the malfunction indicator lamp control circuit and look for a value that is stuck or implausible
- 2Check the malfunction indicator lamp control circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0655Engine test indicator lamp malfunction
Engine test indicator lamp malfunction. The controller logged a fault on the engine test indicator lamp malfunction, which affects how the warning lamp circuit works until the cause is found.· OtherOtherInfoCauses
- Engine test indicator lamp malfunction or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the engine test indicator lamp malfunction and look for a value that is stuck or implausible
- 2Check the engine test indicator lamp malfunction connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB B1002Alternator not charging
The cluster or controller sees no charge from the alternator while the engine is running. The operator sees the charging warning lamp, and the battery will drain until the fault is fixed.· OtherOtherCheck soonCauses
- Alternator failed and not producing charge
- Drive belt broken, slipping or off the pulley
- Loose or corroded alternator output cable
- Alternator excitation wire open
- Cluster or controller sensing the charge signal wrongly
Checks
- 1Check the drive belt is present, tight and in good condition
- 2Measure battery voltage with the engine running and see if it rises above battery voltage
- 3Check the alternator output cable and the earth connection
- 4Check the excitation wire and plug at the alternator
- 5Check the charge indicator wire to the cluster for continuity
- 6Test the alternator output on a bench or replace it if it fails
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB C1025Battery voltage high fault
Battery voltage as seen by the controller is above its limit. The operator may see a charging warning, and electronics can be damaged by sustained overvoltage.· Shorted highShorted highCheck soonCauses
- Alternator regulator failed high
- Poor earth or sensing wire letting the alternator overcharge
- Loose battery terminal confusing the voltage reading
- Wrong or failed battery
- Controller voltage sensing wire damaged
Checks
- 1Measure battery voltage with the engine running and compare it with the controller reading
- 2Check the alternator output voltage at the charging terminal
- 3Check battery earth and alternator earth are clean and tight
- 4Look for loose or corroded battery terminals and cable ends
- 5Check the battery is the correct type and not boiling
- 6Check the controller sensing wire for damage and loose pins
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB C1026Battery voltage low fault
Battery voltage as seen by the controller is below its limit. The operator may see a charging or low voltage warning, and the machine can fail to start or lose electronic functions.· Shorted lowShorted lowCheck soonCauses
- Weak or discharged battery
- Alternator not charging or a slipping belt
- Corroded or loose battery terminals and earth straps
- High resistance in the main supply cable
- Heavy parasitic load or a short draining the battery
Checks
- 1Measure battery voltage with the engine off and while cranking
- 2Check alternator output with the engine running at fast idle
- 3Clean and tighten the battery terminals and earth straps
- 4Voltage-drop test the main supply cable under load
- 5Load test the battery to find weak or dead cells
- 6Check for a circuit drawing current with the key off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB C1027Alternator voltage high fault
The alternator output voltage reads too high at the controller. The operator may see a charging warning, and the battery and electronics can be damaged if it carries on.· Shorted highShorted highCheck soonCauses
- Alternator regulator failed so output is uncontrolled
- Alternator wiring or earth fault upsetting the regulator
- Loose or corroded alternator sense connection
Checks
- 1Measure the alternator output at the terminal with the engine running
- 2Compare the alternator voltage with the battery terminal voltage
- 3Check the alternator earth and the connector for looseness
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB C1028Alternator voltage low fault
The alternator output voltage reads too low at the controller, so the battery is not being charged properly. The operator may see a charging warning, and the battery will drain over time.· Shorted lowShorted lowCheck soonCauses
- Alternator failed or not producing full output
- Drive belt slipping or worn
- Poor connection on the alternator output cable
Checks
- 1Measure the alternator output voltage with the engine at fast idle
- 2Check the drive belt condition and tension on the alternator pulley
- 3Check the alternator output cable and terminals for heat marks and looseness
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB B1309Service interval due / elapsed
The scheduled service interval has been reached or has passed. The operator sees a service reminder on the display, which is a prompt only and does not stop the machine.· OtherOtherInfoCauses
- Service hours reached the programmed interval
- Service done but the interval counter not reset
- Interval programmed too short for the machine
- Controller clock or counter fault after a battery disconnect
- Service reminder left active from an earlier visit
Checks
- 1Check the hour meter against the service schedule in the operator manual
- 2Carry out the service that is due and record it
- 3Reset the service interval with the diagnostic tool or display menu after the work
- 4Check the programmed interval matches the machine model
- 5Confirm the reminder clears after the interval is reset
- 6Check there is no other active fault behind the reminder
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1669DPF lamp fault
DPF lamp fault. The controller logged a fault on the DPF lamp, which affects how the warning lamp circuit works until the cause is found.· OtherOtherInfoCauses
- DPF lamp or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the DPF lamp and look for a value that is stuck or implausible
- 2Check the DPF lamp connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Measure battery voltage engine off and at fast idle, charging should be higher
- 2Check that the lamp lights at key on during the bulb test
- 3Do the service work and reset the service interval counter on the diagnostic tool
- 4Check the alternator belt and the battery and earth connections
- 5Check the cluster connector and wiring for opens and shorts
- 6Check the service interval setting and hour meter on the cluster
- 7Check the alternator output and the excitation wire
Causes
- Weak or sulphated battery
- Lamp or cluster fault
- Service due
- Alternator or regulator faulty or belt slipping
Most common here: shorted high (3 of 13)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: A battery or charging lamp may light and controllers may reset or misbehave if voltage is out of range.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code P0562 page
- Partao JCB fault code list, page 1 (code table)
- Partao JCB fault code list, page 7 (code table)
- Partao JCB fault code P0563 page
- Partao JCB fault code list, page 8 (code table)
- Partao JCB fault code list, page 2 (code table)
- Partao JCB fault code list, page 10 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
