JCB · Machine controller (MECU / DECU)
JCB Fault Code C1021
Engine coolant level low
What does JCB code C1021 mean?
The machine controller sees a low engine coolant level from the level switch or sender. A warning shows on the display and the engine may derate or shut down if the coolant is truly low. Urgency: check soon - the machine may derate or limit a function. Check first: with the engine cold, check the coolant level in the radiator and in the expansion tank.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
With the engine cold, check the coolant level in the radiator and in the expansion tank
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Coolant level genuinely low from a hose, radiator or water pump leak
- Air pocket in the cooling system after a recent drain or repair
- Coolant level sender or switch failed or covered in scale
- Wiring fault or loose connector at the level sender
1 more causeFewer causes
- Overflow bottle cap or pressure cap not sealing and letting coolant out
How it failed
You'll notice: A low coolant warning shows on the display and the engine may derate or shut down if the level is not corrected.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel, oil and coolant temperature sensors and engine overheating
- P0195Oil temperature sensor external voltage faultOtherCheck soon
- P0196Oil temperature sensor signal gradient faultLost messageCheck soon
- P0196-87Missing oil temperature CAN message from engine ECULost messageCheck soon
- P0197Oil temperature sensor signal lowOtherCheck soon
- P0198Oil temperature sensor signal highShorted highCheck soon
- P0217Coolant temperature above limit (overheating)Shorted highStop now
- C1021Engine coolant level lowOtherCheck soon
- B1543Critical high coolant temperatureLost messageStop now
- B1546Coolant temperature high (operator level)OtherCheck soon
Show the other 9 codesHide the other codes
- P0115Coolant temperature sensor 1 circuit faultOtherCheck soon
- P0116Coolant temperature sensor range/performanceErratic or implausibleCheck soon
- P0117Coolant temperature sensor signal lowShorted lowCheck soon
- P0118Coolant temperature sensor signal highOpen circuitCheck soon
- P0180Fuel temperature sensor A circuit faultErratic or implausibleCheck soon
- P0181Fuel temperature sensor faultErratic or implausibleCheck soon
- P0181-87Missing fuel temperature CAN messageLost messageCheck soon
- P0182Fuel temperature sensor A signal lowOtherCheck soon
- P0183Fuel temperature sensor A signal highShorted highCheck soon
Other JCB codes: Machine controller (MECU / DECU)
- C1023Hydraulic oil temperature high alarm
- C102BCooling fan solenoid fault condition
- C102DCooling fan solenoid open circuit
- B105AHigh voltage detected at sensor
- B105BSensor voltage high (throttle control)
- B105CHigh voltage detected at sensor (hydraulic controller)
- B105DLow voltage detected in sensor circuit
Related on Equipments Finder
Source
Partao JCB fault code list, page 2 (code table)
This source lists C1021 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JCB machines with MECU/DECU.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
