J1939 · Turbo
SPN 1127 Fault Code
Engine turbocharger 1 boost pressure
What does SPN 1127 mean?
Boost pressure produced by the turbocharger, read by a pressure sensor on the intake side. The ECM compares it with its target to control boost and limit fuel. How urgent it is depends on the FMI after SPN 1127 - pick it below. Check first: compare the boost reading with the commanded value on a loaded run or a stall test.
- SPN 1127
- Engine turbocharger 1 boost pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 1127 - pick it below.
What should I check first?
Compare the boost reading with the commanded value on a loaded run or a stall test
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 1127?
You'll notice: Turbo boost pressure is not what the ECM commands, so the engine feels short of power, may smoke black or hunt under load, and the check lamp comes on.
Find the number shown after SPN 1127 on your display.
- 0SPN 1127 FMI 0: Value is above the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 1SPN 1127 FMI 1: Value is below the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 10SPN 1127 FMI 10: The value is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 11SPN 1127 FMI 11: A fault exists but the ECM cannot identify its causeOtherMack MP8, Mack MP7, Volvo D13
- 13SPN 1127 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
- 14SPN 1127 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 16SPN 1127 FMI 16: Value is above the normal range, moderately severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 18SPN 1127 FMI 18: Value is below the normal range, moderately severe levelReal conditionMack MP8, Mack MP7, Volvo D13
Checks
0 of 5 done
When to stop
Make the machine safe before you start: on firm level ground, attachments down, key out.
How urgent SPN 1127 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Boost too low: leak at a charge air cooler hose or clamp, a split cooler, or a worn turbo that cannot build pressure
- Boost too high: wastegate or variable-geometry vanes stuck closed, or the actuator not moving
- Actuator control fault: wiring, driver or position sensor fault on the turbo actuator
- Sensor fault: boost pressure sensor or its wiring giving a false reading
Other Turbo codes
- SPN 102Intake manifold (boost) pressure
- SPN 1176Turbocharger compressor inlet pressure
- SPN 641Variable geometry turbo (VGT) actuator
- SPN 642Variable geometry turbocharger actuator 2
- SPN 1172Turbo compressor inlet temperature sensor
- SPN 1188Turbocharger wastegate actuator
- SPN 1209Exhaust gas pressure
- SPN 2629Turbocharger compressor outlet temperature
Source
Mack MP8 2010-2013 fault code list (Diesel Laptops)
This list names SPN 1127 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Mack MP7 and MP8; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
