J1939 · Lubrication
SPN 100 Fault Code
Engine oil pressure
What does SPN 100 mean?
Pressure in the main oil gallery, read by a sensor on the engine block. The ECM uses it for the gauge and for low-pressure warnings, derates and shutdown. How urgent it is depends on the FMI after SPN 100 - pick it below. Check first: fit a mechanical gauge at the sensor port: if the gauge shows normal pressure while the service tool reads full scale, the fault is electrical.
- SPN 100
- Engine oil pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 100 - pick it below.
What should I check first?
Fit a mechanical gauge at the sensor port: if the gauge shows normal pressure while the service tool reads full scale, the fault is electrical
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 100?
You'll notice: The oil pressure gauge reads zero, sticks at the top or flickers and the warning lamp may come on.
Find the number shown after SPN 100 on your display. 4 of them have their own page with causes and checks.
- 0SPN 100 FMI 0: Oil pressure reading is stuck instead of following the engineReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 1SPN 100 FMI 1: Value is below the normal range, most severe levelReal conditionCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
- 2SPN 100 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 3SPN 100 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 4SPN 100 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 5SPN 100 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 10SPN 100 FMI 10: Engine power is being reduced because of low oil pressureErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 13SPN 100 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
- 14SPN 100 FMI 14: The oil pressure sensor failed the ECM's plausibility checkErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 15SPN 100 FMI 15: Value is above the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 17SPN 100 FMI 17: Value is below the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 18SPN 100 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15, PACCAR MX-13
- 20SPN 100 FMI 20: Oil pressure is higher than expected for the engine conditionsErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 21SPN 100 FMI 21: Oil pressure is lower than expected for the engine conditionsErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 31SPN 100 FMI 31: Oil pressure is implausibly low compared with the ECM's expected valueReal conditionDetroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
How urgent SPN 100 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: broken or backed-out pin, an open sensor return, or the signal shorted to the 5 V reference at the oil pressure sensor
- Signal low or shorted: signal wire grounded, or the 5 V reference lost, so the oil pressure sensor reads at the bottom of its range
- Real condition: low oil level, thinned oil or a worn pump leaving real pressure below the limit
- Real condition: oil filter or cooler restricted, or a relief valve stuck open
1 more causeFewer causes
- Sensor: oil-soaked connector seal letting the signal change as the engine shakes
Other Lubrication codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 100 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
