EF Logo

Hyundai · Transmission TCU codes (hex)

Hyundai TCU clutch slippage, torque overload and overtemperature fault codes

These codes report protection events rather than wiring faults: clutch slippage, engine or transmission torque overload, sump and converter output overtemperature, engine overspeed and a clogged oil filter.

FaultCheckBAHyundai · TCU clutch slippage, torque overload and overtemperature
Code shows hereFAULTBA

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes BA to B9 are all about the tCU clutch slippage, torque overload and overtemperature. The most common failure type is real condition (7 of 14); 6 need an immediate stop. Start with this check: check the main pressure and the pressure at the affected clutch.

How urgent are they?

6 of 14 codes here mean stop now; the other 8 can wait until the shift ends, but find the cause before the next one.

  • Stop now6
  • Check soon8

What should I check first?

Check the main pressure and the pressure at the affected clutch

Shared checks

14 of 14

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai BATCU differential pressure at oil filter

    The differential pressure across the transmission oil filter is high, which points to a clogged filter or cold thick oil.· Real condition
    Check soon

    Causes

    • Clogged oil filter
    • Cold oil giving a false reading

    Checks

    1. 1Check and replace the oil filter if it is overdue
    2. 2Check the differential pressure switch and its wiring
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai BBTCU slippage at converter lock-up clutch

    The TCU sees slip at the converter lock-up clutch, so lock-up efficiency is lost.· Other
    Check soon

    Causes

    • Lock-up clutch worn
    • Low lock-up pressure

    Checks

    1. 1Check the lock-up clutch pressure
    2. 2Check the speed sensors used to compute the slip
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C0TCU engine torque or engine power overload

    The calculated engine torque or power is above the permitted limit and the TCU keeps normal operation.· Real condition
    Check soon

    Causes

    • Machine overloaded
    • Engine torque signal wrong

    Checks

    1. 1Check the engine torque signal from the engine controller
    2. 2Check the load the machine was carrying
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai B1TCU slippage at clutch K1

    The TCU calculates a speed difference across closed gear clutch K1, the first of the four numbered gear clutches that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch K1
    • Clutch K1 worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch K1
    2. 2Check the main pressure and the speed sensors
    3. 3Select each gear in turn and see which one the machine refuses, because the missing gear points at the clutch
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C1TCU transmission output torque overload

    The calculated transmission output torque is above the permitted limit and the TCU keeps normal operation.· Real condition
    Check soon

    Causes

    • Machine overloaded
    • Torque calculation using wrong signals

    Checks

    1. 1Check the speed signals used in the calculation
    2. 2Review how the machine was used when the code logged
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai B2TCU slippage at clutch K2

    The TCU calculates a speed difference across closed gear clutch K2, the second numbered gear clutch that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch K2
    • Clutch K2 worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch K2
    2. 2Check the main pressure and the speed sensors
    3. 3Try each gear one by one and note which gears fail to engage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C2TCU transmission input torque overload

    The calculated transmission input torque is above the permitted limit, and the reaction is programmable.· Real condition
    Check soon

    Causes

    • Machine overloaded
    • Engine torque signal wrong

    Checks

    1. 1Check the engine torque signals
    2. 2Review the load and the programmed reaction
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai B3TCU slippage at clutch K3

    The TCU calculates a speed difference across closed gear clutch K3, the third numbered gear clutch that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch K3
    • Clutch K3 worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch K3
    2. 2Check the main pressure and the speed sensors
    3. 3Try each gear and compare against the missing gear to confirm the clutch
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C3TCU converter output overtemperature

    The converter output oil temperature is above its limit and the TCU takes no action beyond the warning.· Real condition
    Check soon

    Causes

    • Converter working hard under heavy load
    • Blocked cooler

    Checks

    1. 1Cool down the machine
    2. 2Check the cooler for blockage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai B4TCU slippage at clutch K4

    The TCU calculates a speed difference across closed gear clutch K4, the fourth numbered gear clutch that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch K4
    • Clutch K4 worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch K4
    2. 2Check the main pressure and the speed sensors
    3. 3Drive up through the gears to find where the transmission stops going up
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai B5TCU slippage at clutch KV

    The TCU calculates a speed difference across closed the forward direction clutch KV that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch KV
    • Clutch KV worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch KV
    2. 2Check the main pressure and the speed sensors
    3. 3Select forward and reverse and see which direction is lost
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai B6TCU slippage at clutch KR

    The TCU calculates a speed difference across closed the reverse direction clutch KR that is out of range and treats this as slipping, so it shifts to neutral.· Other
    Stop now

    Causes

    • Low pressure at clutch KR
    • Clutch KR worn or defective
    • Wrong speed sensor signal or sensor gap

    Checks

    1. 1Check the pressure at clutch KR
    2. 2Check the main pressure and the speed sensors
    3. 3Select forward and reverse and see which direction is lost
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai B7TCU transmission sump overtemperature

    The transmission sump temperature is above its limit and the TCU takes no action beyond the warning.· Real condition
    Check soon

    Causes

    • Overheated oil from heavy work
    • Blocked cooler or low oil level

    Checks

    1. 1Cool down the machine and let the oil temperature fall
    2. 2Check the oil level and the cooler for blockage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai B9TCU engine overspeed

    The engine speed exceeded its limit and the retarder applies to bring it back under control.· Real condition
    Check soon

    Causes

    • Machine running downhill with engine overspeed
    • Wrong engine speed signal

    Checks

    1. 1Review how the machine was driven when the code logged
    2. 2Compare the engine speed signal with a hand tachometer
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the main pressure and the pressure at the affected clutch
  2. 2Check the speed sensors and their gaps against the manual
  3. 3Check the oil level and condition and the oil cooler
  4. 4Check the oil filter and its differential pressure switch for blockage
  5. 5Cool the machine down and see whether the fault clears again

Causes

  • Low clutch pressure or low main pressure
  • Worn or burnt clutch
  • Overheated transmission oil from heavy work or a blocked cooler
  • Speed sensor errors that look like slippage

Most common here: real condition (7 of 14)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The transmission may shift to neutral, the machine may lose drive or show an overheat warning, and the display shows a hex code.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.