EF Logo

Hyundai · Transmission TCU codes (hex)

Hyundai TCU shift lever and clutch cut off inputs fault codes

These TCU codes cover the shift lever direction and range signals, the second shift lever, the engine derating logic check and the clutch cut off input. The TCU compares the lever signals and reports a code when the combination makes no sense.

FaultCheck10Hyundai · TCU shift lever and clutch cut off inputs
Code shows hereFAULT10

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes 10 to 22 are all about the tCU shift lever and clutch cut off inputs. None needs an immediate stop. Start with this check: check the cable from the TCU to the shift lever for breaks and for contact with supply or ground.

How urgent are they?

None of the 7 codes here means stop now; 5 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Check soon5
  • Info2

What should I check first?

Check the cable from the TCU to the shift lever for breaks and for contact with supply or ground

Shared checks

7 of 7

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai 10TCU logical error at direction select signal from shift lever 3

    The TCU sees an impossible direction signal combination from shift lever 3 and shifts to neutral if that lever's selector is active.· Other
    Check soon

    Causes

    • Cable from shift lever 3 broken or shorted
    • Shift lever 3 defective

    Checks

    1. 1Check the cable from the TCU to lever 3 for breaks and contact with supply or ground
    2. 2Check forward, neutral and reverse signal combinations at lever 3
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai 11TCU logical error at gear range signal

    The TCU sees a wrong signal combination for the gear range and shifts the transmission to neutral.· Other
    Check soon

    Causes

    • Cable from the shift lever to the TCU broken
    • Cable shorted to battery voltage or ground
    • Shift lever defective

    Checks

    1. 1Check the gear range signals at the lever against its position
    2. 2Check the cable between the lever and the TCU
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai 12TCU logical error at direction select signal

    The TCU sees a wrong direction signal combination from the shift lever and shifts to neutral, and the fault clears when a valid neutral signal returns.· Other
    Check soon

    Causes

    • Cable from the shift lever broken
    • Cable shorted to battery voltage or ground
    • Shift lever defective

    Checks

    1. 1Check the forward, neutral and reverse combinations at the lever
    2. 2Check the cable and connectors from the lever to the TCU
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai 13TCU logical error at engine derating device

    After the TCU asked for engine derating it saw no reaction from the engine, so it moves to limp home mode.· Other
    Check soon

    Causes

    • Engine derating device not responding
    • Derating wiring or signal fault

    Checks

    1. 1Check the engine derating device and its signal path
    2. 2Cycle TCU power to reset the fault and see whether it returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai 15TCU logical error at direction select signal from shift lever 2

    The TCU sees a wrong direction signal combination from shift lever 2 and shifts to neutral if that lever's selector is active.· Other
    Check soon

    Causes

    • Cable from shift lever 2 broken or shorted
    • Shift lever 2 defective

    Checks

    1. 1Check the cable from the TCU to lever 2
    2. 2Check the forward, neutral and reverse combinations at that lever
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai 21TCU short to battery voltage at clutch cut off input

    The measured voltage on the clutch cut off input is too high, so the clutch cut off function is disabled while the transmission carries on in normal mode.· Shorted high
    Info

    Causes

    • Cable shorted to battery voltage
    • Clutch cut off sensor internal fault
    • Connector pin touching battery voltage

    Checks

    1. 1Check the cable from the TCU to the clutch cut off sensor for a path to supply
    2. 2Check the sensor and its connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 22TCU short to ground or open circuit at clutch cut off input

    The measured voltage on the clutch cut off input is too low, so the clutch cut off function is disabled while the transmission carries on in normal mode.· Shorted low
    Info

    Causes

    • Cable shorted to ground or disconnected
    • Clutch cut off sensor internal fault

    Checks

    1. 1Check the cable from the TCU to the sensor for a break or path to ground
    2. 2Check connector pins and the sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Check the cable from the TCU to the shift lever for breaks and for contact with supply or ground
  2. 2Check the lever signal combinations for F-N-R and gear range with the key on
  3. 3Check the connectors at the lever and at the TCU for pushed-back pins
  4. 4For the clutch cut off input, check the sensor on the brake pedal and its cable
  5. 5Select neutral and cycle the key to see whether the fault resets

Causes

  • Shift lever cable or connector damaged
  • Lever or CAN shift lever failed
  • Clutch cut off sensor wiring or sensor failed
  • Short to battery voltage or ground in the cable

When to stop

You'll notice: The gearbox may stay in neutral until you select neutral, the clutch cut off function may stop, and the display shows a two character hex code.

Make the machine safe before you start: on firm level ground, attachments down, key out.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.