Hyundai · Transmission TCU codes (hex)
Hyundai TCU clutch valve circuits K1 to KR fault codes
The TCU drives one valve per clutch: K1, K2, K3, K4, KV and KR. The TCU measures the resistance of each valve circuit and reports a short to battery voltage, a short to ground or an open circuit.
Where this code shows
Turn the key on and open the fault code or diagnosis menu on the cluster.
What do these codes mean?
Hyundai codes 71 to 89 are all about the tCU clutch valve circuits K1 to KR. The most common failure type is shorted high (6 of 18); 18 need an immediate stop. Start with this check: measure the valve coil resistance at the connector and compare it with the other clutch valves.
How urgent are they?
All 18 codes here mean stop now.
- Stop now18
What should I check first?
Measure the valve coil resistance at the connector and compare it with the other clutch valves
Shared checks18 of 18
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Hyundai 71TCU short to battery voltage at clutch K1
The measured resistance of the valve for gear clutch K1, the first of the four numbered gear clutches looks like a short to battery voltage, so the TCU shifts to neutral. K1 is one of the numbered gear clutches, so losing it takes out the gear that depends on it and the machine may run in limp home with only one gear per direction. After the repair, run the transmission through a full forward and reverse cycle with the parking brake on for a safe static check, then test on the road. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. Of the gear clutches it is the one for the lowest ratio, so a failure shows when pulling away under load. Leaking piston seals, a stuck valve spool, or debris from burnt friction plates are classic culprits behind this circuit. Burnt smell in the oil or dark metal on the filter magnet supports a clutch pack problem. Drag at standstill with the pedal released also hints at residual clutch pressure.· Shorted highShorted highStop nowCauses
- Clutch K1 valve wire touching battery voltage
- Clutch K1 valve coil internal fault
Checks
- 1Check the clutch K1 wire for contact with supply
- 2Measure the clutch K1 coil resistance
- 3Select each gear in turn and see which one the machine refuses, because the missing gear points at the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 72TCU short to ground at clutch K1
The measured resistance of the valve for gear clutch K1, the first of the four numbered gear clutches looks like a short to ground, so the TCU shifts to neutral. K1 is one of the numbered gear clutches, so losing it takes out the gear that depends on it and the machine may run in limp home with only one gear per direction. After the repair, run the transmission through a full forward and reverse cycle with the parking brake on for a safe static check, then test on the road. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. Of the gear clutches it is the one for the lowest ratio, so a failure shows when pulling away under load. Leaking piston seals, a stuck valve spool, or debris from burnt friction plates are classic culprits behind this circuit. Burnt smell in the oil or dark metal on the filter magnet supports a clutch pack problem. Drag at standstill with the pedal released also hints at residual clutch pressure.· Shorted lowShorted lowStop nowCauses
- Clutch K1 valve wire touching ground
- Clutch K1 valve coil shorted
Checks
- 1Check the clutch K1 wire for contact with ground
- 2Measure the clutch K1 coil resistance and compare with a neighbour
- 3Select each gear in turn and see which one the machine refuses, because the missing gear points at the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 73TCU open circuit at clutch K1
The measured resistance of the valve for gear clutch K1, the first of the four numbered gear clutches looks open, so the TCU shifts to neutral. K1 is one of the numbered gear clutches, so losing it takes out the gear that depends on it and the machine may run in limp home with only one gear per direction. After the repair, run the transmission through a full forward and reverse cycle with the parking brake on for a safe static check, then test on the road. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. Of the gear clutches it is the one for the lowest ratio, so a failure shows when pulling away under load. Leaking piston seals, a stuck valve spool, or debris from burnt friction plates are classic culprits behind this circuit. Burnt smell in the oil or dark metal on the filter magnet supports a clutch pack problem. Drag at standstill with the pedal released also hints at residual clutch pressure.· Open circuitOpen circuitStop nowCauses
- Clutch K1 valve wire broken
- Clutch K1 valve coil open
Checks
- 1Check continuity of the clutch K1 wire
- 2Check the clutch K1 valve connector for a pushed-back pin
- 3Select each gear in turn and see which one the machine refuses, because the missing gear points at the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 74TCU short to battery voltage at clutch K2
The measured resistance of the valve for gear clutch K2, the second numbered gear clutch looks like a short to battery voltage, so the TCU shifts to neutral. K2 is another numbered gear clutch, so the gears that use it are lost while the others may still work. After the repair, shift through the gear range in both directions during a short road test and watch for flare or late engagement on the second gear step. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. It sits next in the gear sequence, so a failure shows as a missing second step when accelerating. Worn sealing rings on the drum, restricted feed orifice, or a sticking proportional valve are classic culprits behind this circuit. Glitter in the oil sample or dark fluid supports a clutch pack problem. Surging between steps under moderate throttle suggests unstable pressure.· Shorted highShorted highStop nowCauses
- Clutch K2 valve wire touching battery voltage
- Clutch K2 valve coil internal fault
Checks
- 1Check the clutch K2 wire for contact with supply
- 2Measure the clutch K2 coil resistance
- 3Try each gear one by one and note which gears fail to engage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 75TCU short to ground at clutch K2
The measured resistance of the valve for gear clutch K2, the second numbered gear clutch looks like a short to ground, so the TCU shifts to neutral. K2 is another numbered gear clutch, so the gears that use it are lost while the others may still work. After the repair, shift through the gear range in both directions during a short road test and watch for flare or late engagement on the second gear step. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. It sits next in the gear sequence, so a failure shows as a missing second step when accelerating. Worn sealing rings on the drum, restricted feed orifice, or a sticking proportional valve are classic culprits behind this circuit. Glitter in the oil sample or dark fluid supports a clutch pack problem. Surging between steps under moderate throttle suggests unstable pressure.· Shorted lowShorted lowStop nowCauses
- Clutch K2 valve wire touching ground
- Clutch K2 valve coil shorted
Checks
- 1Check the clutch K2 wire for contact with ground
- 2Measure the clutch K2 coil resistance and compare with a neighbour
- 3Try each gear one by one and note which gears fail to engage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 76TCU open circuit at clutch K2
The measured resistance of the valve for gear clutch K2, the second numbered gear clutch looks open, so the TCU shifts to neutral. K2 is another numbered gear clutch, so the gears that use it are lost while the others may still work. After the repair, shift through the gear range in both directions during a short road test and watch for flare or late engagement on the second gear step. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. It sits next in the gear sequence, so a failure shows as a missing second step when accelerating. Worn sealing rings on the drum, restricted feed orifice, or a sticking proportional valve are classic culprits behind this circuit. Glitter in the oil sample or dark fluid supports a clutch pack problem. Surging between steps under moderate throttle suggests unstable pressure.· Open circuitOpen circuitStop nowCauses
- Clutch K2 valve wire broken
- Clutch K2 valve coil open
Checks
- 1Check continuity of the clutch K2 wire
- 2Check the clutch K2 valve connector for a pushed-back pin
- 3Try each gear one by one and note which gears fail to engage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 77TCU short to battery voltage at clutch K3
The measured resistance of the valve for gear clutch K3, the third numbered gear clutch looks like a short to battery voltage, so the TCU shifts to neutral. K3 is the third numbered gear clutch, so the gears that need it drop out and the machine may fall back to one gear. After the repair, shift up and down through the gears and watch for flare or slip on the third gear step. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. It sits next in the gear sequence, so a failure shows as a missing third step when accelerating. A cracked sealing ring, scored piston bore, or sticky regulator can also upset this circuit. Fine bronze or paper debris on the filter points to pack wear. Delayed engagement after a kickdown indicates sluggish valve response.· Shorted highShorted highStop nowCauses
- Clutch K3 valve wire touching battery voltage
- Clutch K3 valve coil internal fault
Checks
- 1Check the clutch K3 wire for contact with supply
- 2Measure the clutch K3 coil resistance
- 3Try each gear and compare against the missing gear to confirm the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 78TCU short to ground at clutch K3
The measured resistance of the valve for gear clutch K3, the third numbered gear clutch looks like a short to ground, so the TCU shifts to neutral. K3 is the third numbered gear clutch, so the gears that need it drop out and the machine may fall back to one gear. After the repair, shift up and down through the gears and watch for flare or slip on the third gear step. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. It sits next in the gear sequence, so a failure shows as a missing third step when accelerating. A cracked sealing ring, scored piston bore, or sticky regulator can also upset this circuit. Fine bronze or paper debris on the filter points to pack wear. Delayed engagement after a kickdown indicates sluggish valve response.· Shorted lowShorted lowStop nowCauses
- Clutch K3 valve wire touching ground
- Clutch K3 valve coil shorted
Checks
- 1Check the clutch K3 wire for contact with ground
- 2Measure the clutch K3 coil resistance and compare with a neighbour
- 3Try each gear and compare against the missing gear to confirm the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 79TCU open circuit at clutch K3
The measured resistance of the valve for gear clutch K3, the third numbered gear clutch looks open, so the TCU shifts to neutral. K3 is the third numbered gear clutch, so the gears that need it drop out and the machine may fall back to one gear. After the repair, shift up and down through the gears and watch for flare or slip on the third gear step. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. It sits next in the gear sequence, so a failure shows as a missing third step when accelerating. A cracked sealing ring, scored piston bore, or sticky regulator can also upset this circuit. Fine bronze or paper debris on the filter points to pack wear. Delayed engagement after a kickdown indicates sluggish valve response.· Open circuitOpen circuitStop nowCauses
- Clutch K3 valve wire broken
- Clutch K3 valve coil open
Checks
- 1Check continuity of the clutch K3 wire
- 2Check the clutch K3 valve connector for a pushed-back pin
- 3Try each gear and compare against the missing gear to confirm the clutch
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 81TCU short to battery voltage at clutch K4
The measured resistance of the valve for gear clutch K4, the fourth numbered gear clutch looks like a short to battery voltage, so the TCU shifts to neutral. K4 is the fourth numbered gear clutch, so the highest gears that need it are lost. After the repair, accelerate through the full gear range and watch for flare or slip at the top gear step. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. It is the last of the numbered gear clutches, so a failure shows at road speed. Damaged sealing rings, a weak return spring or a dirty modulator are further suspects here. Varnished oil and scored plates point to overheating of this pack. Reduced top speed with normal acceleration suggests the top step is unavailable.· Shorted highShorted highStop nowCauses
- Clutch K4 valve wire touching battery voltage
- Clutch K4 valve coil internal fault
Checks
- 1Check the clutch K4 wire for contact with supply
- 2Measure the clutch K4 coil resistance
- 3Drive up through the gears to find where the transmission stops going up
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 82TCU short to ground at clutch K4
The measured resistance of the valve for gear clutch K4, the fourth numbered gear clutch looks like a short to ground, so the TCU shifts to neutral. K4 is the fourth numbered gear clutch, so the highest gears that need it are lost. After the repair, accelerate through the full gear range and watch for flare or slip at the top gear step. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. It is the last of the numbered gear clutches, so a failure shows at road speed. Damaged sealing rings, a weak return spring or a dirty modulator are further suspects here. Varnished oil and scored plates point to overheating of this pack. Reduced top speed with normal acceleration suggests the top step is unavailable.· Shorted lowShorted lowStop nowCauses
- Clutch K4 valve wire touching ground
- Clutch K4 valve coil shorted
Checks
- 1Check the clutch K4 wire for contact with ground
- 2Measure the clutch K4 coil resistance and compare with a neighbour
- 3Drive up through the gears to find where the transmission stops going up
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 83TCU open circuit at clutch K4
The measured resistance of the valve for gear clutch K4, the fourth numbered gear clutch looks open, so the TCU shifts to neutral. K4 is the fourth numbered gear clutch, so the highest gears that need it are lost. After the repair, accelerate through the full gear range and watch for flare or slip at the top gear step. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. It is the last of the numbered gear clutches, so a failure shows at road speed. Damaged sealing rings, a weak return spring or a dirty modulator are further suspects here. Varnished oil and scored plates point to overheating of this pack. Reduced top speed with normal acceleration suggests the top step is unavailable.· Open circuitOpen circuitStop nowCauses
- Clutch K4 valve wire broken
- Clutch K4 valve coil open
Checks
- 1Check continuity of the clutch K4 wire
- 2Check the clutch K4 valve connector for a pushed-back pin
- 3Drive up through the gears to find where the transmission stops going up
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 84TCU short to battery voltage at clutch KV
The measured resistance of the valve for the forward direction clutch KV looks like a short to battery voltage, so the TCU shifts to neutral. KV is the forward direction clutch, so the machine may refuse to move forward while reverse still works. After the repair, select forward from a standstill several times and watch for slow engagement or a delay. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. As the forward clutch it carries all forward driving, so a failure shows as no drive forward. Directional clutch pack wear, drum seal leakage and valve contamination are the further suspects. Slow forward engagement after warm up hints at pack or seal leakage. Crawling forward only on high throttle hints at partial fill.· Shorted highShorted highStop nowCauses
- Clutch KV valve wire touching battery voltage
- Clutch KV valve coil internal fault
Checks
- 1Check the clutch KV wire for contact with supply
- 2Measure the clutch KV coil resistance
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 85TCU short to ground at clutch KV
The measured resistance of the valve for the forward direction clutch KV looks like a short to ground, so the TCU shifts to neutral. KV is the forward direction clutch, so the machine may refuse to move forward while reverse still works. After the repair, select forward from a standstill several times and watch for slow engagement or a delay. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. As the forward clutch it carries all forward driving, so a failure shows as no drive forward. Directional clutch pack wear, drum seal leakage and valve contamination are the further suspects. Slow forward engagement after warm up hints at pack or seal leakage. Crawling forward only on high throttle hints at partial fill.· Shorted lowShorted lowStop nowCauses
- Clutch KV valve wire touching ground
- Clutch KV valve coil shorted
Checks
- 1Check the clutch KV wire for contact with ground
- 2Measure the clutch KV coil resistance and compare with a neighbour
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 86TCU open circuit at clutch KV
The measured resistance of the valve for the forward direction clutch KV looks open, so the TCU shifts to neutral. KV is the forward direction clutch, so the machine may refuse to move forward while reverse still works. After the repair, select forward from a standstill several times and watch for slow engagement or a delay. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. As the forward clutch it carries all forward driving, so a failure shows as no drive forward. Directional clutch pack wear, drum seal leakage and valve contamination are the further suspects. Slow forward engagement after warm up hints at pack or seal leakage. Crawling forward only on high throttle hints at partial fill.· Open circuitOpen circuitStop nowCauses
- Clutch KV valve wire broken
- Clutch KV valve coil open
Checks
- 1Check continuity of the clutch KV wire
- 2Check the clutch KV valve connector for a pushed-back pin
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 87TCU short to battery voltage at clutch KR
The measured resistance of the valve for the reverse direction clutch KR looks like a short to battery voltage, so the TCU shifts to neutral. KR is the reverse direction clutch, so the machine may refuse to move backward while forward still works. After the repair, select reverse from a standstill several times and watch for slow engagement or a delay. A short to battery voltage usually shows up as a valve held on, so the clutch may stay filled and the machine can drag or refuse to release. As the reverse clutch it carries all reverse driving, so a failure shows as no drive backward. Reverse pack wear, leaking drum seals and contaminated modulator valves are the further suspects. Slow reverse engagement after warm up hints at pack or seal leakage. Crawling backward only on high throttle hints at partial fill.· Shorted highShorted highStop nowCauses
- Clutch KR valve wire touching battery voltage
- Clutch KR valve coil internal fault
Checks
- 1Check the clutch KR wire for contact with supply
- 2Measure the clutch KR coil resistance
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 88TCU short to ground at clutch KR
The measured resistance of the valve for the reverse direction clutch KR looks like a short to ground, so the TCU shifts to neutral. KR is the reverse direction clutch, so the machine may refuse to move backward while forward still works. After the repair, select reverse from a standstill several times and watch for slow engagement or a delay. A short to ground usually shows up as a valve that cannot be driven, so the clutch never fills and the machine slips or will not engage. As the reverse clutch it carries all reverse driving, so a failure shows as no drive backward. Reverse pack wear, leaking drum seals and contaminated modulator valves are the further suspects. Slow reverse engagement after warm up hints at pack or seal leakage. Crawling backward only on high throttle hints at partial fill.· Shorted lowShorted lowStop nowCauses
- Clutch KR valve wire touching ground
- Clutch KR valve coil shorted
Checks
- 1Check the clutch KR wire for contact with ground
- 2Measure the clutch KR coil resistance and compare with a neighbour
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 89TCU open circuit at clutch KR
The measured resistance of the valve for the reverse direction clutch KR looks open, so the TCU shifts to neutral. KR is the reverse direction clutch, so the machine may refuse to move backward while forward still works. After the repair, select reverse from a standstill several times and watch for slow engagement or a delay. An open circuit looks like a dead valve, so the clutch never fills even though the coil may be fine and the break sits in the wire or plug. As the reverse clutch it carries all reverse driving, so a failure shows as no drive backward. Reverse pack wear, leaking drum seals and contaminated modulator valves are the further suspects. Slow reverse engagement after warm up hints at pack or seal leakage. Crawling backward only on high throttle hints at partial fill.· Open circuitOpen circuitStop nowCauses
- Clutch KR valve wire broken
- Clutch KR valve coil open
Checks
- 1Check continuity of the clutch KR wire
- 2Check the clutch KR valve connector for a pushed-back pin
- 3Select forward and reverse and see which direction is lost
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Shared checks
Checks, in order
- 1Measure the valve coil resistance at the connector and compare it with the other clutch valves
- 2Check the cable from the TCU to the valve block for breaks and chafing
- 3Check the connector at the valve block for oil, water and bent pins
- 4Check the TCU connector pin for that clutch
- 5Clear the code, run the transmission through its gears and retest
Causes
- Valve coil open or shorted
- Wire from the TCU to the valve block broken or chafed
- Connector at the transmission valve block corroded
- Pin contact to battery voltage or ground
Most common here: shorted high (6 of 18)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The transmission shifts to neutral or runs in limp home mode, and the display shows a two character hex code for that clutch.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
