Cummins · Fuel system
Cummins Engine misfire fault codes
The ECM detects a misfire from crankshaft speed changes and attributes it to a cylinder or to several cylinders. It is a result code that points toward a fuel, air or mechanical problem in that cylinder.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 1654 to 5914 are all about the engine misfire. None needs an immediate stop. Start with this check: run a cylinder cutout or power balance test in INSITE to find the weak cylinder.
How urgent are they?
None of the 14 codes here means stop now; 1 can wait until the shift ends, but find the cause before the next one; 13 are information only.
- Check soon1
- Info13
What should I check first?
Run a cylinder cutout or power balance test in INSITE to find the weak cylinder
Shared checks14 of 14
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Cummins 1654Engine misfire cylinder 1 - Condition exists
Same failure as 5914 on the engine misfire cylinder 1: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 1
- Wiring or connector problem local to the engine misfire cylinder 1
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 1 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1655Engine misfire cylinder 2 - Condition exists
Same failure as 5914 on the engine misfire cylinder 2: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 2
- Wiring or connector problem local to the engine misfire cylinder 2
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 2 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1656Engine misfire cylinder 3 - Condition exists
Same failure as 5914 on the engine misfire cylinder 3: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 3
- Wiring or connector problem local to the engine misfire cylinder 3
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 3 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1657Engine misfire cylinder 4 - Condition exists
Same failure as 5914 on the engine misfire cylinder 4: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 4
- Wiring or connector problem local to the engine misfire cylinder 4
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 4 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1658Engine misfire cylinder 5 - Condition exists
Same failure as 5914 on the engine misfire cylinder 5: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 5
- Wiring or connector problem local to the engine misfire cylinder 5
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 5 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1659Engine misfire cylinder 6 - Condition exists
Same failure as 5914 on the engine misfire cylinder 6: the same fault condition as 5914, reported for this part. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder 6
- Wiring or connector problem local to the engine misfire cylinder 6
Checks
- 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder 6 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 1718Engine misfire - Multiple cylinders
The ECM detects misfire on more than one cylinder. The cause is often shared by the cylinders: fuel supply, rail pressure, air or the control module. Several cylinders are misfiring together, so the cause is more likely shared (fuel supply, air or a common circuit) than one injector.· OtherOtherCheck soonCauses
- Fuel supply restriction or air in the fuel
- Low rail pressure
- Injector fault on several cylinders
Checks
- 1Read all fuel and rail pressure codes and treat those first
- 2Check the fuel filters and the supply pressure
- 3Run the cylinder cut-out test to see which cylinders are weak
- 4Check fuel pressure, filter condition and aeration before pulling a single injector.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5895Engine misfire cylinder #1 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #1: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #1
- Wiring or connector problem local to the engine misfire cylinder #1
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #1 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5896Engine misfire cylinder #2 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #2: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #2
- Wiring or connector problem local to the engine misfire cylinder #2
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #2 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5897Engine misfire cylinder #3 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #3: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #3
- Wiring or connector problem local to the engine misfire cylinder #3
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #3 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5898Engine misfire cylinder #4 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #4: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #4
- Wiring or connector problem local to the engine misfire cylinder #4
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #4 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5899Engine misfire cylinder #5 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #5: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #5
- Wiring or connector problem local to the engine misfire cylinder #5
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #5 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5911Engine misfire cylinder #6 - Root cause not known
Same failure as 5914 on the engine misfire cylinder #6: the same fault condition as 5914, reported for this part. The ECM found a misfire on this cylinder but did not link it to an injector or compression fault.· OtherOtherInfoCauses
- Same causes as 5914, applied to the engine misfire cylinder #6
- Wiring or connector problem local to the engine misfire cylinder #6
Checks
- 1Run a cylinder cutout or power balance test in INSITE to confirm which cylinder is weak.
- 2Work through the checks listed for 5914, starting at the engine misfire cylinder #6 and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cummins 5914Engine misfire for multiple cylinders - Root cause not known
The ECM measured an uneven crankshaft acceleration after the engine misfire for multiple cylinders firing event and logged a misfire. It is a result code: the real cause may be fuel, air, compression or the injector. Several cylinders are misfiring together, so the cause is more likely shared (fuel supply, air or a common circuit) than one injector.· OtherOtherInfoCauses
- Injector for this cylinder sticking, worn or partly blocked
- Low compression from a leaking valve, head gasket or worn ring
- Air or water in the fuel reaching that cylinder
Checks
- 1Run a cylinder cutout or power balance test in INSITE and see which cylinder does not change engine speed when cut
- 2Check fuel pressure at idle and under load and look for air in the fuel with a clear line
- 3Do a compression or leak-down test on the cylinder that was identified
- 4Check fuel pressure, filter condition and aeration before pulling a single injector.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Run a cylinder cutout or power balance test in INSITE to find the weak cylinder
- 2Check fuel pressure, filter condition and the fuel itself for water and air
- 3Do a compression or leak-down test on the cylinder identified
- 4Check valve lash and the rocker and pushrod train
- 5Check the charge-air system and EGR for leaks that starve a cylinder of air
Causes
- Injector for the misfiring cylinder worn, sticking or blocked
- Low compression from valves, head gasket or rings
- Fuel quality, air in the fuel or low fuel pressure
- Charge-air leak or EGR leakage upsetting the air supply
When to stop
You'll notice: Rough running, shaking at idle, loss of power and sometimes white smoke or fuel smell from the exhaust.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
