EF Logo

Cummins · Operator controls

Cummins Cruise control and vehicle speed limit fault codes

The cruise control enable, set, resume and pause switches send the driver's requests to the ECM, usually through the vehicle data link. A disable command from another module tells the ECM to cancel cruise control, for example for traction control or a brake event.

More about these parts

Adaptive and predictive cruise features rely on messages from radar, map and cruise modules. The vehicle speed limiting governor lets the operator change the speed limit with enable, increment and decrement switches, within the maximum the fleet has set.

FaultCheck784Cummins · Adaptive cruise control mode
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 784 to 15684 are all about the cruise control and vehicle speed limit. The most common failure type is erratic or implausible (11 of 25); none needs an immediate stop. Start with this check: watch each switch state in INSITE while pressing it on the stalk or panel.

How urgent are they?

None of the 25 codes here means stop now; 23 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Check soon23
  • Info2

What should I check first?

Watch each switch state in INSITE while pressing it on the stalk or panel

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Adaptive cruise control mode3 codes

    • Cummins 784Adaptive cruise control mode: Erratic reading

      The ECM judges the adaptive cruise control mode to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact on the adaptive cruise control mode
      • Part ageing or failing and giving unstable output
      • Electrical noise from a poorly routed wire or a bad ground

      Checks

      1. 1Watch the adaptive cruise control mode live in INSITE and wiggle the harness and connector to catch dropouts
      2. 2Compare the adaptive cruise control mode with a related reading to decide which one is wrong
      3. 3Check the connector for moisture and corrosion and the ground connection for tightness
      4. 4Check the radar or collision-mitigation module for its own faults, alignment and supply.
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Adaptive cruise control mode - data erratic or incorrect

    • Cummins 7425Adaptive cruise control mode: Abnormal update rate

      Same failure as 14337 on the adaptive cruise control mode: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the adaptive cruise control mode
      • Wiring or connector problem local to the adaptive cruise control mode

      Checks

      1. 1Check the radar or collision-mitigation module for its own faults, alignment and supply.
      2. 2Work through the checks listed for 14337, starting at the adaptive cruise control mode and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    • Cummins 7426Adaptive cruise control mode: Network data in error

      Same failure as 7427 on the adaptive cruise control mode: the same fault condition as 7427, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 7427, applied to the adaptive cruise control mode
      • Wiring or connector problem local to the adaptive cruise control mode

      Checks

      1. 1Check the radar or collision-mitigation module for its own faults, alignment and supply.
      2. 2Work through the checks listed for 7427, starting at the adaptive cruise control mode and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Adaptive cruise control mode - network data received in error

  • Cruise control disable command4 codes

    • Cummins 3843Cruise control disable command: Abnormal update rate

      Same failure as 14337 on the cruise control disable command: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the cruise control disable command
      • Wiring or connector problem local to the cruise control disable command

      Checks

      1. 1Read the controller that sends the disable command for a reason code before touching the ECM.
      2. 2Work through the checks listed for 14337, starting at the cruise control disable command and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    • Cummins 3844Cruise control disable command: Condition exists

      Same failure as 3845 on the cruise control disable command: the same fault condition as 3845, reported for this part.· Other
      Info

      Causes

      • Same causes as 3845, applied to the cruise control disable command
      • Wiring or connector problem local to the cruise control disable command

      Checks

      1. 1Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
      2. 2Work through the checks listed for 3845, starting at the cruise control disable command and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 3845Cruise control disable command: Condition exists

      The ECM has flagged a condition on the cruise control disable command.· Other
      Info

      Causes

      • The underlying system problem that the ECM is reporting on the cruise control disable command
      • A related sensor or circuit fault that triggered this condition
      • Operating conditions outside what the strategy expects

      Checks

      1. 1Read all active and inactive codes and work the circuit or sensor codes for the cruise control disable command first
      2. 2Check the live data around the cruise control disable command while reproducing the operating condition
      3. 3Inspect the system the cruise control disable command belongs to for leaks, blockage or damage
      4. 4Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 7427Cruise control disable command: Network data in error

      The ECM received data for the cruise control disable command over the network, but the message was flagged as in error.· Lost message
      Check soon

      Causes

      • Sending module flagging the data as not available or in error
      • Data link noise, a wiring fault or a bad terminator
      • Mismatched configuration between the ECM and the sending module

      Checks

      1. 1Read the sending module for its own codes and the source sensor for faults
      2. 2Check the data link wiring and terminators for faults near the cruise control disable command source
      3. 3Check the ECM and sending module configuration for the cruise control disable command
      4. 4Read the controller that sends the disable command for a reason code before touching the ECM.
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Cruise control disable command - network data received in error

  • Predictive cruise control state1 code

    • Cummins 6575Predictive cruise control state: Abnormal update rate

      Same failure as 14337 on the predictive cruise control state: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the predictive cruise control state
      • Wiring or connector problem local to the predictive cruise control state

      Checks

      1. 1Check the route parameter module and its GPS and map status for faults.
      2. 2Work through the checks listed for 14337, starting at the predictive cruise control state and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • ACC usage demand1 code

    • Cummins 11439ACC usage demand: Abnormal update rate

      Same failure as 14337 on the ACC usage demand: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the ACC usage demand
      • Wiring or connector problem local to the ACC usage demand

      Checks

      1. 1Check the radar or collision-mitigation module for its own faults, alignment and supply.
      2. 2Work through the checks listed for 14337, starting at the ACC usage demand and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cruise control enable switch2 codes

    • Cummins 14337Cruise control enable switch: Abnormal update rate

      The ECM is not receiving fresh data for the cruise control enable switch at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message for the cruise control enable switch is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and both terminators near the cruise control enable switch source
      3. 3Read the module that sends the cruise control enable switch for its own codes and for power or ground faults
      4. 4Toggle the enable switch on and off and confirm the state changes each time in INSITE.
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Cummins 15684Cruise control enable switch: Out of calibration

      The ECM reports the cruise control enable switch as out of calibration: the value or setting it received does not match what the ECM was programmed to expect.· Part or controller
      Check soon

      Causes

      • Parameter set for a feature that is not fitted on this vehicle
      • Wrong or outdated calibration in the ECM
      • Source module sending an invalid or unscaled value for the cruise control enable switch

      Checks

      1. 1Compare the ECM parameters with the vehicle equipment, especially those that enable the cruise control enable switch
      2. 2Reflash the ECM with the correct calibration if the software level does not match
      3. 3Read the source module for its own codes and check its configuration
      4. 4Toggle the enable switch on and off and confirm the state changes each time in INSITE.
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Cruise control pause switch1 code

    • Cummins 14338Cruise control pause switch: Abnormal update rate

      Same failure as 14337 on the cruise control pause switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the cruise control pause switch
      • Wiring or connector problem local to the cruise control pause switch

      Checks

      1. 1Operate the pause switch and confirm the state toggles and then clears when released.
      2. 2Work through the checks listed for 14337, starting at the cruise control pause switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cruise control resume switch2 codes

    • Cummins 14339Cruise control resume switch: Out of calibration

      Same failure as 15684 on the cruise control resume switch: the same fault condition as 15684, reported for this part.· Part or controller
      Check soon

      Causes

      • Same causes as 15684, applied to the cruise control resume switch
      • Wiring or connector problem local to the cruise control resume switch

      Checks

      1. 1Press resume after braking and confirm the state follows the switch in INSITE.
      2. 2Work through the checks listed for 15684, starting at the cruise control resume switch and its connector
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14341Cruise control resume switch: Abnormal update rate

      Same failure as 14337 on the cruise control resume switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the cruise control resume switch
      • Wiring or connector problem local to the cruise control resume switch

      Checks

      1. 1Press resume after braking and confirm the state follows the switch in INSITE.
      2. 2Work through the checks listed for 14337, starting at the cruise control resume switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cruise control set switch2 codes

    • Cummins 14342Cruise control set switch: Out of calibration

      Same failure as 15684 on the cruise control set switch: the same fault condition as 15684, reported for this part.· Part or controller
      Check soon

      Causes

      • Same causes as 15684, applied to the cruise control set switch
      • Wiring or connector problem local to the cruise control set switch

      Checks

      1. 1Press and hold set at steady speed and confirm the state changes only while it is pressed.
      2. 2Work through the checks listed for 15684, starting at the cruise control set switch and its connector
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14343Cruise control set switch: Abnormal update rate

      Same failure as 14337 on the cruise control set switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the cruise control set switch
      • Wiring or connector problem local to the cruise control set switch

      Checks

      1. 1Press and hold set at steady speed and confirm the state changes only while it is pressed.
      2. 2Work through the checks listed for 14337, starting at the cruise control set switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Vehicle limiting speed governor decrement switch2 codes

    • Cummins 14386Vehicle limiting speed governor decrement switch: Out of calibration

      Same failure as 15684 on the vehicle limiting speed governor decrement switch: the same fault condition as 15684, reported for this part.· Part or controller
      Check soon

      Causes

      • Same causes as 15684, applied to the vehicle limiting speed governor decrement switch
      • Wiring or connector problem local to the vehicle limiting speed governor decrement switch

      Checks

      1. 1Press decrement and confirm the limit steps down smoothly.
      2. 2Work through the checks listed for 15684, starting at the vehicle limiting speed governor decrement switch and its connector
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14387Vehicle limiting speed governor decrement switch: Abnormal update rate

      Same failure as 14337 on the vehicle limiting speed governor decrement switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the vehicle limiting speed governor decrement switch
      • Wiring or connector problem local to the vehicle limiting speed governor decrement switch

      Checks

      1. 1Press decrement and confirm the limit steps down smoothly.
      2. 2Work through the checks listed for 14337, starting at the vehicle limiting speed governor decrement switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Vehicle limiting speed governor enable switch2 codes

    • Cummins 14388Vehicle limiting speed governor enable switch: Out of calibration

      Same failure as 15684 on the vehicle limiting speed governor enable switch: the same fault condition as 15684, reported for this part.· Part or controller
      Check soon

      Causes

      • Same causes as 15684, applied to the vehicle limiting speed governor enable switch
      • Wiring or connector problem local to the vehicle limiting speed governor enable switch

      Checks

      1. 1Toggle the enable switch and confirm the governor state changes in INSITE.
      2. 2Work through the checks listed for 15684, starting at the vehicle limiting speed governor enable switch and its connector
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14389Vehicle limiting speed governor enable switch: Abnormal update rate

      Same failure as 14337 on the vehicle limiting speed governor enable switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the vehicle limiting speed governor enable switch
      • Wiring or connector problem local to the vehicle limiting speed governor enable switch

      Checks

      1. 1Toggle the enable switch and confirm the governor state changes in INSITE.
      2. 2Work through the checks listed for 14337, starting at the vehicle limiting speed governor enable switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Vehicle limiting speed governor increment switch2 codes

    • Cummins 14391Vehicle limiting speed governor increment switch: Out of calibration

      Same failure as 15684 on the vehicle limiting speed governor increment switch: the same fault condition as 15684, reported for this part.· Part or controller
      Check soon

      Causes

      • Same causes as 15684, applied to the vehicle limiting speed governor increment switch
      • Wiring or connector problem local to the vehicle limiting speed governor increment switch

      Checks

      1. 1Press increment and confirm the limit steps up and stops at the programmed maximum.
      2. 2Work through the checks listed for 15684, starting at the vehicle limiting speed governor increment switch and its connector
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14392Vehicle limiting speed governor increment switch: Abnormal update rate

      Same failure as 14337 on the vehicle limiting speed governor increment switch: the same fault condition as 14337, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 14337, applied to the vehicle limiting speed governor increment switch
      • Wiring or connector problem local to the vehicle limiting speed governor increment switch

      Checks

      1. 1Press increment and confirm the limit steps up and stops at the programmed maximum.
      2. 2Work through the checks listed for 14337, starting at the vehicle limiting speed governor increment switch and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Selected maximum vehicle speed limit3 codes

    • Cummins 14611Selected maximum vehicle speed limit: Abnormal update rate

      Same failure as 14337 on the selected maximum vehicle speed limit: the same fault condition as 14337, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 14337, applied to the selected maximum vehicle speed limit
      • Wiring or connector problem local to the selected maximum vehicle speed limit

      Checks

      1. 1Check the programmed maximum speed parameter and the source module that sends the selected limit.
      2. 2Work through the checks listed for 14337, starting at the selected maximum vehicle speed limit and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Cummins 14612Selected maximum vehicle speed limit: Out of calibration

      Same failure as 15684 on the selected maximum vehicle speed limit: the same fault condition as 15684, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 15684, applied to the selected maximum vehicle speed limit
      • Wiring or connector problem local to the selected maximum vehicle speed limit

      Checks

      1. 1Check the programmed maximum speed parameter and the source module that sends the selected limit.
      2. 2Work through the checks listed for 15684, starting at the selected maximum vehicle speed limit and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Cummins 14613Selected maximum vehicle speed limit: Out of calibration

      Same failure as 15684 on the selected maximum vehicle speed limit: the same fault condition as 15684, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 15684, applied to the selected maximum vehicle speed limit
      • Wiring or connector problem local to the selected maximum vehicle speed limit

      Checks

      1. 1Check the programmed maximum speed parameter and the source module that sends the selected limit.
      2. 2Work through the checks listed for 15684, starting at the selected maximum vehicle speed limit and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Watch each switch state in INSITE while pressing it on the stalk or panel
  2. 2Check which module is sending the cruise disable command
  3. 3Check the cruise or radar module for its own codes
  4. 4Press the increment and decrement switches and watch the speed limit values change in INSITE
  5. 5Check the stalk or switch panel connector for corrosion and bent pins
  6. 6Look for data link faults on the J1939 network
  7. 7Look at the data link for timeouts and missing messages

Causes

  • Switch contacts worn or the stalk failed
  • Other module commanding the disable
  • Radar or cruise module offline
  • Up/down switch pack worn out or its connector corroded

Most common here: erratic or implausible (11 of 25)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: Cruise control may not set or resume, or may cancel at random.

Brake and steering faults are a safety issue on site. Chock the machine and keep it parked until the fault is found and the brakes are tested.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.