Cat · Event codes
Cat Fault Code E396
High fuel rail pressure
What does Cat code E396 mean?
The engine ECM detected excessive fuel rail pressure. The 924H manual says the engine is derated until the ignition is turned off. Urgency: stop now - shut down and fix before working on. Check first: connect Cat ET and check for active diagnostic codes; repair them first.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Connect Cat ET and check for active diagnostic codes; repair them first.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Fuel rail pressure sensor fault (1797-3 or 1797-4)
- Fuel pump or rail pressure control fault
- Rail pressure valve solenoid problem (1779)
How it failed
You'll notice: The panel warning lights and engine power is limited until the key is cycled.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel rail pressure and injectors
- CID 4 FMI 06Fuel injector 4 current highShorted lowCheck soon
- CID 6 FMI 02Fuel injector 6 data incorrectErratic or implausibleCheck soon
- CID 6 FMI 05Fuel injector 6 current lowOpen circuitCheck soon
- CID 6 FMI 06Fuel injector 6 current highShorted lowCheck soon
- E396High fuel rail pressureOtherStop now
- E398Low fuel rail pressureOtherStop now
- CID 526 FMI 05Wastegate solenoid current lowOpen circuitCheck soon
- CID 1779 FMI 05Fuel rail pressure valve solenoid current lowOpen circuitStop now
- CID 1797 FMI 03Fuel rail pressure sensor voltage highShorted highStop now
Show the other 10 codesHide the other codes
- CID 1 FMI 02Fuel injector 1 data incorrectErratic or implausibleCheck soon
- CID 1 FMI 05Fuel injector 1 current lowOpen circuitCheck soon
- CID 1 FMI 06Fuel injector 1 current highShorted lowCheck soon
- CID 1 FMI 07Fuel injector 1 mechanical system not respondingPart or controllerCheck soon
- CID 2 FMI 02Fuel injector 2 data incorrectErratic or implausibleCheck soon
- CID 2 FMI 05Fuel injector 2 current lowOpen circuitCheck soon
- CID 3 FMI 02Fuel injector 3 data incorrectErratic or implausibleCheck soon
- CID 3 FMI 05Fuel injector 3 current lowOpen circuitCheck soon
- CID 4 FMI 05Fuel injector 4 current lowOpen circuitCheck soon
- CID 1797 FMI 04Fuel rail pressure sensor voltage lowShorted lowStop now
Other Cat codes: Event codes
Related on Equipments Finder
Source
TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E396)
This source lists E396 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
