Bobcat · Hydraulics
Bobcat Fault Code M0515
Hydraulic charge pressure shutdown
What does Bobcat code M0515 mean?
The controller shut the engine down because charge pressure fell below the protection level. Urgency: stop now - shut down and fix before working on. Check first: check the sensor plug and wiring for water; a wet plug can drop the signal low and trip the shutdown.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the sensor plug and wiring for water; a wet plug can drop the signal low and trip the shutdown
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Pressure transducer failing and reading below the real value
- Leak between the pump and the filter
- Blocked charge filter
- Charge pump worn out
How it failed
You'll notice: The controller stopped the engine on very low charge pressure.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Hydraulic charge pressure, workgroup and load sensing pressure
- M0509Hydraulic charge pressure lowOtherCheck soon
- M0510Hydraulic charge pressure highOtherCheck soon
- M0511Hydraulic charge pressure extremely highLost messageCheck soon
- M0514Hydraulic charge pressure extremely lowOtherStop now
- M0515Hydraulic charge pressure shutdownOtherStop now
- M0521Hydraulic charge pressure out of range highOtherCheck soon
- M0522Hydraulic charge pressure out of range lowOtherCheck soon
- C1080-FAHydraulic charge pressure highLost messageCheck soon
- C1080-FBHydraulic charge pressure extremely highOtherStop now
Show the other 18 codesHide the other codes
- 05-09Hydraulic charge pressure lowReal conditionCheck soon
- 05-14Hydraulic charge pressure extremely lowOtherStop now
- 05-15Hydraulic charge pressure shutdown levelReal conditionStop now
- 05-21Hydraulic charge pressure out of range highOtherCheck soon
- 05-22Hydraulic charge pressure out of range lowOtherCheck soon
- C101D-16Tilt rod pressure sensor out of range lowOtherCheck soon
- C101D-17Tilt rod pressure sensor out of range highOtherCheck soon
- C1080-F8Hydraulic charge pressure extremely lowOtherStop now
- C1080-F9Low hydraulic pump pressureOtherCheck soon
- C1097-16Hydraulic charge pressure sensor out of range lowOtherCheck soon
- C1097-17Hydraulic charge pressure sensor out of range highOtherCheck soon
- H1421Lift base pressure out of range highOtherCheck soon
- H1422Lift base pressure out of range lowOtherCheck soon
- M2521Load sense sensor out of range highOtherCheck soon
- M2522Load sense sensor out of range lowOtherCheck soon
- M6204Load moment sensor in errorOtherCheck soon
- M6221Overload warning sensor out of range highReal conditionCheck soon
- M6222Overload warning sensor out of range lowReal conditionCheck soon
Other Bobcat codes: Hydraulics
- VSE001-00Oil temp. sensor, signal above normal range
- VSP001-02Front pump press. sensor, incorrect signal
- VSE001-03Oil temp. sensor, voltage above normal
- VSP001-03Front pump press. sensor, voltage above normal
- VSE001-04Oil temp. sensor, voltage below normal
- VSP001-04Front pump press. sensor, voltage below normal
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M0515 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders S450-S850 and T450-T870.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
