Bobcat · Engine
Bobcat Engine speed, ECU messages and power derate fault codes
The controller reads engine speed from a crankshaft or camshaft sensor and exchanges messages with the engine ECU over the CAN bus. These codes cover a bad speed signal, lost or invalid ECU messages and the power or torque derates the ECU applies to protect the engine.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes 06-10 to M9701 are all about the engine speed, ECU messages and power derate. The most common failure type is real condition (4 of 20); 6 need an immediate stop. Start with this check: read all active engine codes together: a derate code is usually a symptom of another fault, so fix that one first.
How urgent are they?
6 of 20 codes here mean stop now; 13 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Stop now6
- Check soon13
- Info1
What should I check first?
Read all active engine codes together: a derate code is usually a symptom of another fault, so fix that one first.
Shared checks20 of 20
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat 06-10Engine speed high
The engine speed reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the engine speed belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat 06-11Engine speed extremely high
The engine speed is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 06-13Engine speed no signal
No engine speed signal reaches the controller. The machine may crank but not start, or may stall.· OtherOtherCheck soonCauses
- Broken wire or loose pin in the sensor plug
- Wrong air gap or damaged tone wheel
- Failed speed sensor
- Engine speed sensor not fully seated
Checks
- 1Check that the speed sensor is fully seated in its bore and the bracket bolt is tight; a loose sensor loses pulses
- 2Look at the flywheel or tone ring teeth through the sensor hole for damage
- 3Check that the sensor shield or ground wire is connected, since a broken shield lets noise swamp the signal
- 4Measure continuity of each sensor wire back to the controller with the key off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 06-15Engine speed shutdown level
Engine speed reached the shutdown limit. The engine stops to protect itself from overspeed.· Real conditionReal conditionStop nowCauses
- Excess load suddenly removed from the engine
- Controller commanding too much throttle
- Mechanical throttle linkage or governor sticking
Checks
- 1Review whether the machine ran away down a slope or lost its hydraulic load suddenly, which can overspeed the engine
- 2Inspect the fuel stop solenoid action by watching it close when the key goes off
- 3Check the throttle linkage and the injection pump lever for freedom and a return that is sprung properly
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat 06-18Engine speed out of range
The engine speed signal is outside the range the controller accepts. The reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Sensor or its wiring fault
- Loose connector
- Supply or ground problem on the circuit
Checks
- 1Check the connector at the engine speed for moisture and bent pins
- 2Check supply and ground at the plug with the key on using a meter
- 3Compare the live reading with a separate gauge
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0610Engine speed too high
The engine speed has gone above the allowed running speed. The controller may limit the engine while this is active.· Real conditionReal conditionCheck soonCauses
- Throttle calibration out of date
- Load suddenly removed from the engine
- Speed sensor reading too high from noise
Checks
- 1Inspect the throttle cable or linkage for a binding pivot or dirt in the return spring
- 2Look for any recent calibration work; throttle sensors need recalibrating after being moved or replaced
- 3Check the throttle sensor reading on the display at rest and full travel for smooth movement without jumps
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0611Engine speed extremely high
The engine overspeeded. Stop it and find why before running again. Stop it and find why before running again.· Real conditionReal conditionStop nowCauses
- Governor spring broken
- Throttle sensor failed full on
- Speed sensor giving a false extremely high count
Checks
- 1Check the air intake and turbo for oil leaking in, which can make the engine run on its own oil
- 2Inspect the turbo shaft for play or oil seepage that could point to a runaway cause
- 3Test the throttle sensor with the key on and look for a reading stuck at the top
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0613Engine speed no signal
The controller is not getting a speed pulse from the engine. The machine may crank but not start, or stall.· OtherOtherCheck soonCauses
- Wrong air gap or damaged tone wheel
- Failed speed sensor
- Debris or metal on the sensor tip
- Broken wire or loose pin in the sensor plug
Checks
- 1Unplug the sensor and check the plug for pushed-back pins or corrosion before testing anything else
- 2With the engine cranking, measure for a signal at the sensor; no signal at all with intact wiring points at the sensor or the ring
- 3Pull the sensor and examine its tip for metal fragments and for a worn face from hitting the tone ring
- 4Swap in a known good sensor and recheck the speed reading on the display
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0615Engine speed shutdown
The engine speed passed the level where the controller shuts the engine down. The engine stops to protect itself from overspeed.· Real conditionReal conditionStop nowCauses
- Controller commanding too much throttle
- Speed sensor feeding a false high count
- Excess load suddenly removed from the engine
Checks
- 1Look at the speed sensor wiring and the shield for pickup noise that could create phantom pulses
- 2Compare the displayed rpm with a hand tachometer on a restart at idle
- 3Check the throttle position sensor reading at rest; a failed sensor can command full throttle
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0618Engine speed out of range
The speed signal is outside what the controller accepts, often a sensor or wiring problem.· OtherOtherCheck soonCauses
- Poor sensor ground
- Wiring chafed near a hot or moving part
- Tone wheel damage
Checks
- 1Check that the shield and ground are connected at both ends and the connector seals are intact
- 2Check the speed sensor mounting and the gap to the tone wheel against the manual specification
- 3Fit a known good sensor and see whether the range code clears at the same speed
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0634Engine speed invalid data
The engine speed information the controller receives is not valid, usually after a communication problem with the engine ECU.· OtherOtherCheck soonCauses
- Sensor failing intermittently
- Corrupt controller memory
- Damaged wiring on the speed circuit
Checks
- 1Inspect the harness between the engine and the controller for chafe and green corrosion in the plugs
- 2Check for software update notices for the engine or machine controller from Bobcat
- 3If the data stays invalid with clean wiring, the controller or engine module needs to be diagnosed with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4028Wrong ECU detected
The controller logged the message "Wrong ECU detected". The code list gives no failure mode beyond the name, so treat it as a status or fault message from the controller.· OtherOtherCheck soonCauses
- Condition the message names is active
- Wiring or connector problem on the related part
- Software or programming mismatch
Checks
- 1Read the message in context with any other active code
- 2Check the related part and its plug for damage
- 3Clear the code and see whether it returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4228Wrong DCU detected
The controller logged the message "Wrong DCU detected". The code list gives no failure mode beyond the name, so treat it as a status or fault message from the controller.· OtherOtherCheck soonCauses
- Condition the message names is active
- Wiring or connector problem on the related part
- Software or programming mismatch
Checks
- 1Read the message in context with any other active code
- 2Check the related part and its plug for damage
- 3Clear the code and see whether it returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M6604ECU no communication
The controller cannot talk to the ecu. Messages are missing on the CAN network, so the part or controller may not work properly.· Lost messageLost messageCheck soonCauses
- Loose or corroded CAN connector
- CAN wire broken or shorted
- Device without power or damaged
Checks
- 1Check the supply and ground at the ecu plug
- 2Check the CAN wires for continuity and for shorts to each other
- 3Reseat the connectors and cycle the key to see if communication returns
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M6904DCU no communication
The controller cannot talk to the dcu. Messages are missing on the CAN network, so the part or controller may not work properly.· Lost messageLost messageCheck soonCauses
- Loose or corroded CAN connector
- CAN wire broken or shorted
- Device without power or damaged
Checks
- 1Check the supply and ground at the dcu plug
- 2Check the CAN wires for continuity and for shorts to each other
- 3Reseat the connectors and cycle the key to see if communication returns
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M8615Engine speed derate shutdown
The engine speed has reached the level at which the controller shuts the machine down or cuts power to protect it.· OtherOtherStop nowCauses
- Condition that stayed in warning until it reached shutdown
- Blocked cooler, filter or line
- Sensor reading in shutdown range
Checks
- 1Do not keep working; fix the underlying fault first
- 2Check the warning codes for the same system that set before this one
- 3Verify the real value with a separate gauge before restarting
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M8625Engine speed derate unresponsive
The engine speed derate is unresponsive, so its reading does not change when the machine moves. The controller cannot rely on the signal.· OtherOtherCheck soonCauses
- Sensor failed or not mounted correctly
- Signal wire broken
- Mechanical drive to the sensor missing
Checks
- 1Check the engine speed derate is fitted tight and its air gap or linkage is correct
- 2Watch its live reading while moving the machine
- 3Check the signal wire for breaks
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M8715Torque derate shutdown
The torque has reached the level at which the controller shuts the machine down or cuts power to protect it.· OtherOtherStop nowCauses
- Condition that stayed in warning until it reached shutdown
- Blocked cooler, filter or line
- Sensor reading in shutdown range
Checks
- 1Do not keep working; fix the underlying fault first
- 2Check the warning codes for the same system that set before this one
- 3Verify the real value with a separate gauge before restarting
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M8725Torque derate unresponsive
The torque derate is unresponsive, so its reading does not change when the machine moves. The controller cannot rely on the signal.· OtherOtherCheck soonCauses
- Sensor failed or not mounted correctly
- Signal wire broken
- Mechanical drive to the sensor missing
Checks
- 1Check the torque derate is fitted tight and its air gap or linkage is correct
- 2Watch its live reading while moving the machine
- 3Check the signal wire for breaks
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M9701Turbo prime sequence active
The controller logged the message "Turbo prime sequence active". The code list gives no failure mode beyond the name, so treat it as a status or fault message from the controller.· OtherOtherInfoCauses
- Condition the message names is active
- Wiring or connector problem on the related part
- Software or programming mismatch
Checks
- 1Read the message in context with any other active code
- 2Check the related part and its plug for damage
- 3Clear the code and see whether it returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read all active engine codes together: a derate code is usually a symptom of another fault, so fix that one first.
- 2Check the speed sensor mounting and connector, and look for a damaged tone wheel or metal debris on the sensor tip.
- 3Check the CAN high and CAN low wires at the ECU connector for chafing, water and bent pins.
- 4Measure resistance across the two CAN wires with the key off; a reading far from the expected pair of terminating resistors points to a break.
- 5After the repair clear the codes and run the engine through its speed range to confirm the derate is gone.
Causes
- Speed sensor gap wrong, sensor loose or dirty with metal debris
- CAN wiring fault or a missing terminating resistor causing message loss
- ECU in a derate caused by another active engine fault
- Loose engine harness connector or ground
Most common here: real condition (4 of 20)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The engine runs at reduced power, will not reach full speed, or stalls; the tachometer may jump or read zero.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
- Bobcat S205 Operation & Maintenance Manual, service codes list
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
