Kubota · DPF regeneration (E:90xx)
Kubota Fault Code E:9004
DPF replacement required
What does Kubota code E:9004 mean?
The particulate filter is so loaded with ash and soot that regeneration cannot restore it. The filter has to be serviced or replaced and the engine may be limited. Urgency: stop now - shut down and fix before working on. Check first: review history for repeated failed regenerations.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Review history for repeated failed regenerations
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Filter loaded with ash beyond what regeneration can burn
- Long period of unsuccessful regenerations
- Engine fault pushing excess soot into the exhaust
- Cracked or melted DPF substrate
How it failed
You'll notice: Red DPF lamp with E:9004; reduced engine power or limited operation until the filter is serviced.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF, regeneration and particulate accumulation
- E:9000DPF regeneration required (low rpm prevents start)Lost messageCheck soon
- E:9001DPF regeneration requiredLost messageCheck soon
- E:9002DPF regeneratedOtherInformation
- E:9003DPF regeneration required (cannot start)OtherCheck soon
- E:9004DPF replacement requiredOtherStop now
- E:9006DPF regeneration required (inhibit switch active)OtherCheck soon
- E:9007DPF regeneration required (inhibit switch active, engine may stop)Lost messageCheck soon
- E:9010Engine stop for DPFOtherStop now
- E:9204Differential pressure sensor system errorOtherCheck soon
Show the other 15 codesHide the other codes
- SPN3251-FMI3DPF differential pressure sensor - open circuit or short to batteryShorted highCheck soon
- SPN3251-FMI4DPF differential pressure sensor - ground shortShorted lowCheck soon
- SPN3701-FMI0PM accumulation level 5Real conditionStop now
- SPN3701-FMI15PM accumulation level 3Real conditionCheck soon
- SPN3701-FMI16PM accumulation level 4Real conditionCheck soon
- SPN3936-FMI2Loss of function of DPF (PCD)Erratic or implausibleCheck soon
- SPN3936-FMI7Removal of DPF (PCD)Part or controllerCheck soon
- E:9211DOC response unusualLost messageCheck soon
- E:9212DPF regeneration timeoutLost messageCheck soon
- E:9213DPF regeneration error (water temperature low)Lost messageCheck soon
- E:9214DPF regeneration cycle occurs too oftenOtherCheck soon
- SPN523589-FMI17Low coolant temperature in parked regenerationReal conditionCheck soon
- SPN523590-FMI16Parked regeneration time outReal conditionCheck soon
- SPN523602-FMI0High frequency of regenerationReal conditionCheck soon
- SPN523603-FMI15Overheat pre-cautionReal conditionCheck soon
Related on Equipments Finder
Source
This source lists E:9004 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota SSV65, SSV75, SVL65-2, SVL75-3, SVL97-2 loaders (the models the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
