Kubota · DPF regeneration (E:90xx)
Kubota DPF, regeneration and particulate accumulation fault codes
This page covers the diesel particulate filter: regeneration messages and faults, parked regeneration and the overheat precaution, the differential pressure sensor, particulate matter accumulation levels and DPF removal detection. The diesel particulate filter collects soot and burns it off in a regeneration.
More about these partsLess
These codes show that a regeneration did not run as planned: the catalyst did not heat the exhaust, the regeneration took too long, it stopped because the engine was too cold, or it is happening too often. These codes show that a parked regeneration was stopped because the coolant was too cold or it took too long, that regenerations happen too often, or that the engine is nearing overheat. The differential pressure sensor measures the pressure drop across the particulate filter to estimate soot load. The engine ECU estimates the soot load of the particulate filter. The engine ECU checks that the particulate filter is fitted and working.
Where this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
What do these codes mean?
Kubota codes SPN3251-FMI3 to SPN523603-FMI15 are all about the dPF, regeneration and particulate accumulation. The most common failure type is real condition (7 of 24); 3 need an immediate stop. Start with this check: read the message and check whether the regeneration inhibit switch is off.
How urgent are they?
3 of 24 codes here mean stop now; 20 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Stop now3
- Check soon20
- Info1
What should I check first?
Read the message and check whether the regeneration inhibit switch is off
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Kubota SPN3251-FMI3DPF differential pressure sensor - Open circuit or short to battery
SPN 3251 FMI 3 means the DPF differential pressure sensor reads above range or is open. Soot load cannot be calculated correctly.· Shorted highShorted highCheck soonCauses
- Sensor failed high
- Signal wire open or shorted to supply
- Blocked pressure hose
Checks
- 1Read the sensor at key on engine off; a high reading with no pressure confirms a high-side fault
- 2Check the signal wire for a short to supply or an open
- 3Blow through the pressure hoses and check for soot plugs
- 4Inspect the differential pressure sensor connector for water ingress
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Kubota SPN3251-FMI4DPF differential pressure sensor - Ground short
SPN 3251 FMI 4 means the DPF differential pressure sensor reads below range, usually an open or grounded signal. Soot load cannot be calculated correctly.· Shorted lowShorted lowCheck soonCauses
- Sensor failed low
- Signal wire shorted to ground
- Hose or fitting problem
Checks
- 1Read the sensor at key on engine off; it should sit near zero
- 2Check the differential pressure sensor signal wire for a short to ground
- 3Inspect the pressure hoses for cracks and kinks
- 4Check the sensor connector for water ingress and bent pins
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Kubota SPN3701-FMI0PM accumulation level 5
SPN 3701 FMI 0 means soot accumulation in the particulate filter has reached level 5. The ECU applies stronger limits at each level.· Real conditionReal conditionStop nowCauses
- Regeneration not completing
- Sensor fault hiding the real load
- Engine running at light load
Checks
- 1Run a parked regeneration as the manual describes
- 2Read the differential pressure and soot level in Diagmaster
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN3701-FMI15PM accumulation level 3
SPN 3701 FMI 15 means soot accumulation in the particulate filter has reached level 3. The ECU applies stronger limits at each level.· Real conditionReal conditionCheck soonCauses
- Regeneration not completing
- Sensor fault hiding the real load
- Engine running at light load
Checks
- 1Run a parked regeneration as the manual describes
- 2Read the differential pressure and soot level in Diagmaster
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN3701-FMI16PM accumulation level 4
SPN 3701 FMI 16 means soot accumulation in the particulate filter has reached level 4. The ECU applies stronger limits at each level.· Real conditionReal conditionCheck soonCauses
- Regeneration not completing
- Sensor fault hiding the real load
- Engine running at light load
Checks
- 1Run a parked regeneration as the manual describes
- 2Read the differential pressure and soot level in Diagmaster
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN3936-FMI2Loss of function of DPF (PCD)
SPN 3936 FMI 2 means the particulate filter no longer performs as expected. It is probably cracked or damaged.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Filter cracked or melted
- Exhaust leak before the filter
- Sensor fault
Checks
- 1Inspect the filter for damage
- 2Read the differential pressure and compare with the soot estimate
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Kubota SPN3936-FMI7Removal of DPF (PCD)
SPN 3936 FMI 7 means the ECU believes the particulate filter has been removed. The ECU may limit power.· Part or controllerPart or controllerCheck soonCauses
- Filter removed or substituted
- Differential pressure hoses leaking or off
- Sensor fault
Checks
- 1Confirm the filter is fitted
- 2Check the pressure hoses and sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Kubota E:9000DPF regeneration required (low rpm prevents start)
Soot has built up in the diesel particulate filter and the engine needs a regeneration, but engine speed is too low for it to begin. Raise engine speed or work the machine so the regeneration can start.· Lost messageLost messageCheck soonCauses
- Engine run at low idle for long periods so the filter never gets hot
- Short runs that never reach regeneration temperature
- Regeneration inhibit switch left on
- Soot load rising because of an engine or sensor fault
Checks
- 1Confirm the DPF inhibit switch is off and the machine has fuel and normal coolant temperature
- 2Raise engine speed and start a parked regeneration with the DPF switch as described in the operator's manual
- 3Watch the exhaust temperature rise and the code clear when the regeneration completes
- 4Read differential pressure and exhaust temperatures in Diagmaster to see how loaded the filter is
- 5If it repeats, check for air intake restriction and exhaust temperature sensor faults
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9001DPF regeneration required
The controller requests a DPF regeneration because soot is accumulating. This is the early stage of the soot warning, shown so the operator can act before power is reduced.· Lost messageLost messageCheck soonCauses
- Regeneration not performed as scheduled
- Frequent idling or light duty keeping exhaust cool
- Differential pressure sensor misreading soot load
- Regeneration blocked by the inhibit switch
Checks
- 1Start a manual regeneration with the DPF switch while the loader is parked and level
- 2Confirm the exhaust temperature sensors read sensibly against each other
- 3Check the DPF differential pressure hoses for kinks, cracks and soot blockage
- 4Check that no other engine codes are preventing regeneration
- 5Work the machine under load next shift to avoid repeat requests
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9002DPF regenerated
The controller reports that the particulate filter has just been regenerated. It is informational, and the soot warning should now be gone.· OtherOtherInfoCauses
- Normal completion of an automatic regeneration
- Manual regeneration started by the operator
- Scheduled soot burn-off finishing
Checks
- 1Confirm the DPF lamp has gone off after the regeneration finished
- 2Let the engine idle briefly before shutdown if the operator's manual asks for it
- 3Note how often regenerations happen so a developing problem shows up early
- 4If regenerations come very often, check for E:9214 and the differential pressure sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9003DPF regeneration required (cannot start)
The DPF needs regeneration but conditions such as low coolant temperature or an inhibit condition stop it from starting. Soot keeps building and a stronger warning follows if it is ignored.· OtherOtherCheck soonCauses
- Coolant not warm enough to allow regeneration
- Regeneration inhibit switch active
- Exhaust temperature sensor fault blocking regeneration
Checks
- 1Warm the engine until coolant reaches operating temperature, then retry
- 2Make sure the inhibit switch is off and its circuit is not shorted
- 3Read the exhaust temperature sensor values and check they are plausible
- 4Check for stored E:9203 and E:9205 to E:9208 codes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9004DPF replacement required
The particulate filter is so loaded with ash and soot that regeneration cannot restore it. The filter has to be serviced or replaced and the engine may be limited.· OtherOtherStop nowCauses
- Filter loaded with ash beyond what regeneration can burn
- Long period of unsuccessful regenerations
- Engine fault pushing excess soot into the exhaust
- Cracked or melted DPF substrate
Checks
- 1Review history for repeated failed regenerations
- 2Read the DPF differential pressure at idle and compare it with a known good machine
- 3Inspect the exhaust inlet and outlet for soot and heat damage
- 4Have the DPF cleaned or replaced by a Kubota dealer
- 5Reset the soot counters with Diagmaster after the service
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9006DPF regeneration required (inhibit switch active)
A regeneration is needed but the regeneration inhibit switch is on, so the loader will not burn off the soot. Switch the inhibit off and let the regeneration run.· OtherOtherCheck soonCauses
- DPF inhibit switch left on
- Inhibit switch circuit shorted
- Operator working where regeneration must be avoided
Checks
- 1Check the position of the inhibit switch on the dash and the lamp beside it
- 2Test the switch contacts with a meter in both positions
- 3Check the switch wires for a short to ground or to the supply
- 4Turn inhibit off and start a parked regeneration as the manual describes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9007DPF regeneration required (inhibit switch active, engine may stop)
A regeneration is needed but cannot start because the inhibit switch is on. If the machine is left with the hydraulics locked the engine can stop by itself, so it must be restarted and the switch released.· Lost messageLost messageCheck soonCauses
- Regeneration inhibit switch left on
- Machine parked with the hydraulics locked
- Soot load rising unnoticed
Checks
- 1Release the inhibit switch and restart the engine
- 2Start the regeneration as the manual describes
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9010Engine stop for DPF
The engine control unit stops the engine to protect the exhaust system because the DPF is dangerously loaded or too hot. Service is needed before it will restart normally.· OtherOtherStop nowCauses
- DPF soot load beyond limit after ignored warnings
- DPF overheating
- Failed regeneration cycles
Checks
- 1Check the stored DPF codes and earlier warnings to see how the soot load got there
- 2Inspect the DPF and exhaust pipes for heat damage and soot leakage
- 3Have the soot level and differential pressure read in Diagmaster
- 4Perform a service regeneration or replace the DPF at a Kubota dealer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9204Differential pressure sensor system error
The sensor that measures pressure drop across the DPF is reporting a bad value, so the ECU cannot judge soot load. Regeneration decisions become unreliable.· OtherOtherCheck soonCauses
- Differential pressure sensor failed
- Cracked or blocked pressure hoses to the DPF
- Wiring fault at the sensor
- Exhaust leak at a pipe fitting
Checks
- 1Inspect both pressure hoses and their fittings for cracks, soot plugs and loose clamps
- 2Read differential pressure at key on engine off; it should be near zero
- 3Back-probe supply, ground and signal at the sensor
- 4Check the exhaust joints for leaks near the DPF
- 5Replace the sensor if the reading will not settle near zero with the engine off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota E:9211DOC response unusual
The oxidation catalyst is not heating the exhaust as expected when fuel is dosed. That can mean a worn catalyst or a fuelling problem.· Lost messageLost messageCheck soonCauses
- DOC catalyst degraded or coated with soot
- Fuel dosing problem
- Exhaust sensor reading wrong
Checks
- 1Review stored DPF codes and regeneration history in Diagmaster
- 2Compare the exhaust temperatures during a regeneration
- 3Check the injectors and fuel supply for faults
- 4Inspect the air intake and cleaner for restriction that would starve the burn
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9212DPF regeneration timeout
A regeneration started but did not finish within the allowed time. The soot load remains and another request will follow.· Lost messageLost messageCheck soonCauses
- Engine shut down during the regeneration
- Low exhaust temperature
- Regeneration interrupted by load changes
Checks
- 1Allow the regeneration to finish with the machine parked and idling
- 2Check the exhaust temperature sensors read plausibly
- 3Check the intake throttle valve moves freely and is not choked with soot
- 4Look for other active codes blocking the regeneration
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9213DPF regeneration error (water temperature low)
Regeneration was stopped because the coolant temperature was too low. The engine has to be warm before the filter can be cleaned.· Lost messageLost messageCheck soonCauses
- Engine not warm
- Thermostat stuck open
- Coolant temperature sensor fault
Checks
- 1Warm the engine fully before starting a regeneration
- 2Check that the thermostat closes and opens properly
- 3Compare the coolant temperature display with a thermometer
- 4Check the coolant level in the radiator, since low coolant can show cold readings
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Kubota E:9214DPF regeneration cycle occurs too often
Regeneration is happening more often than normal, which points to excess soot production or a faulty sensor. The filter and engine may be at risk.· OtherOtherCheck soonCauses
- Differential pressure sensor misreading
- Engine making too much soot
- DOC or DPF damaged
- Air or fuel system fault
Checks
- 1Check the differential pressure sensor and its hoses
- 2Check the air intake and injectors for faults
- 3Review the regeneration history in Diagmaster
- 4Inspect the DPF for cracks and heavy ash build-up with the dealer's help
- 5Repair whatever is making the extra soot before it damages the filter
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Kubota SPN523589-FMI17Low coolant temperature in parked regeneration
SPN 523589 FMI 17 means a parked regeneration was stopped because the coolant stayed too cold. The regeneration does not finish.· Real conditionReal conditionCheck soonCauses
- Thermostat stuck open
- Cold ambient conditions
- Coolant sensor reading low
Checks
- 1Warm the engine up to operating temperature before starting the regeneration
- 2Check the thermostat operation
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN523590-FMI16Parked regeneration time out
SPN 523590 FMI 16 means the parked regeneration took longer than allowed. The ECU stops it.· Real conditionReal conditionCheck soonCauses
- Exhaust sensor or catalyst fault
- Very high soot load
- Cold engine
Checks
- 1Check for sensor codes first
- 2Repeat the regeneration after the engine is warm
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN523602-FMI0High frequency of regeneration
SPN 523602 FMI 0 means regenerations happen more often than normal. That points to excess soot production.· Real conditionReal conditionCheck soonCauses
- Injector or air supply fault
- Oil in the exhaust
- Sensor fault
Checks
- 1Check for sensor and injector codes
- 2Check the oil level and consumption
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Kubota SPN523603-FMI15Overheat pre-caution
SPN 523603 FMI 15 means the engine is approaching an overheat condition. It is an early warning.· Real conditionReal conditionCheck soonCauses
- Blocked cooler
- Low coolant
- Fan problem
Checks
- 1Clean the cooler and check the coolant level
- 2Check the fan operation
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Read the message and check whether the regeneration inhibit switch is off
- 2Check for other active engine and sensor codes and fix those first
- 3Check the coolant temperature reaches the normal working range
- 4Inspect both pressure hoses for blockage and cracks
- 5Run the regeneration as the operator's manual describes
- 6Inspect the exhaust system to confirm the filter is fitted
- 7Move the machine to a safe open area and start the regeneration as the operator's manual describes
Causes
- Differential pressure sensor hose blocked or sensor failed
- Long periods of idling or light load that never reach regeneration temperature
- Exhaust temperature or differential pressure sensor fault
- Cold coolant from a stuck-open thermostat
Most common here: real condition (7 of 24)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A DPF lamp and an E:90xx message on the meter; the engine may be limited in power until the regeneration is done.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- CodeReady - Kubota Skid Steer Loader Error Codes (SSV65, SSV75, SVL65-2, SVL75-3, SVL97-2), error code table
- Kato Works - Kubota engine error codes (SPN / FMI table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
