Kubota · Loader controller (E:0xx)
Kubota Fault Code E:023
Jump start with a 24 V battery or improper device
What does Kubota code E:023 mean?
The controller sees an overvoltage consistent with a 24 V jump start or an improper charger. Electronics can be damaged, so the machine reports the condition right away. Urgency: stop now - shut down and fix before working on. Check first: measure battery voltage at rest and with the engine running; a 12 V system should not go above about 15 V.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Measure battery voltage at rest and with the engine running; a 12 V system should not go above about 15 V
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Loader jumped from a 24 V system
- Charger or booster connected incorrectly
- Alternator regulator producing overvoltage
- Battery cables connected in reverse polarity
How it failed
You'll notice: E:023 after a jump start or charger connection; the machine may refuse to run or lose controllers.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Loader controller supply, drive and fan
6 other codes on this part are also lost message (E:001, E:009, E:011, E:021 and more). When they show together, start at the wiring and connector they share.
- E:001CAN communication errorLost messageCheck soon
- E:008Fuel sensor system errorOtherCheck soon
- E:009Acceleration system errorLost messageCheck soon
- E:011Parking brake system errorLost messageStop now
- E:020Electronic travel torque management system errorOtherCheck soon
- E:021Sensor 5 V power supply short-circuitedLost messageCheck soon
- E:022Fan rpm control solenoid valve cable brokenOpen circuitCheck soon
- E:023Jump start with a 24 V battery or improper deviceLost messageStop now
- E:026CRS CAN communication errorLost messageCheck soon
- E:028Fan solenoid broken or short-circuitedLost messageCheck soon
Other Kubota codes: Loader controller (E:0xx)
- E:024Hydraulic oil temperature sensor error
- E:027Ride control solenoid broken or short-circuited
- E:029Hydraulic lock solenoid (arm) broken or short-circuited
- E:030Hydraulic lock solenoid (bucket) broken or short-circuited
- E:031High-speed mode pressure sensor broken or short-circuited
- E:032Float mode selector solenoid cable broken or short-circuited
Related on Equipments Finder
Source
This source lists E:023 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota SSV65, SSV75, SVL65-2, SVL75-3, SVL97-2 loaders (the models the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
