EF Logo

Detroit · Injectors

Detroit Injector needle valves fault codes

Each cylinder has a Detroit injector with a needle control valve that the MCM drives with a current pulse, plus a matching amplifier valve (listed in another family). SPN 651 to 656 are the needle valves of cylinders 1 to 6, SPN 2797 and 2798 flag a bank-wide short, and SPN 7384 to 7389 are the cold-start versions.

FaultCheckSPN 651FMI 3Detroit · Injector needle valves
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 651 FMI 3 to SPN 2798 FMI 4 are all about the injector needle valves. The most common failure type is shorted low (14 of 28); none needs an immediate stop. Start with this check: read the code with the cylinder number and check whether the same cylinder also logs a misfire or an amplifier valve code.

How urgent are they?

None of the 28 codes here means stop now; all 28 can wait until the shift ends, but find the cause before the next one.

  • Check soon28

What should I check first?

Read the code with the cylinder number and check whether the same cylinder also logs a misfire or an amplifier valve code.

Shared checks

28 of 28

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 651 FMI 3Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)

    Detroit lists SPN 651 FMI 3 as "Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • A partial short inside the needle valve coil or in the injector connector pulling extra current
    • Wire insulation damaged so the circuit leaks to another wire

    Checks

    1. 1Measure the needle valve coil resistance at the harness connector and compare it with the other cylinders; a low value points to a shorted coil.
    2. 2Look for a damaged section of the valve cover harness where two injector wires touch.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 651 FMI 4Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)

    Detroit lists SPN 651 FMI 4 as "Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • High resistance in the needle valve circuit from a corroded pin or a half-broken wire
    • Weak or sticking solenoid in the injector

    Checks

    1. 1Check the needle valve connector pins for corrosion and spread terminals, then measure the circuit resistance end to end.
    2. 2Compare the value against a cylinder that has no code to see how far this one is out.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 651 FMI 5Injector Cylinder #1 Needle Control Valve Circuit Open

    Detroit lists SPN 651 FMI 5 as "Injector Cylinder #1 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • Broken wire or a pushed-out pin between the MCM and the needle valve
    • Burned-out injector solenoid

    Checks

    1. 1Check continuity of both needle valve wires between the MCM connector and the injector connector under the valve cover.
    2. 2Measure the solenoid resistance; an open reading means the injector has failed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 651 FMI 6Injector Cylinder #1 Needle Control Valve Shorted Circuit

    Detroit lists SPN 651 FMI 6 as "Injector Cylinder #1 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • Shorted needle valve solenoid winding
    • Two injector wires rubbed together under the valve cover

    Checks

    1. 1Unplug the needle valve at the injector and see whether the short remains; if it goes away the injector is shorted.
    2. 2Check between the injector wires and to ground at the harness side for a dead short.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 652 FMI 3Injector Cylinder #2 Needle Control Valve Abnormal Operation (MAX)

    Same failure as SPN 651 FMI 3 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)") on a sibling part: Detroit lists SPN 652 FMI 3 as "Injector Cylinder #2 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 652 FMI 4Injector Cylinder #2 Needle Control Valve Abnormal Operation (MIN)

    Same failure as SPN 651 FMI 4 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)") on a sibling part: Detroit lists SPN 652 FMI 4 as "Injector Cylinder #2 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 652 FMI 5Injector Cylinder #2 Needle Control Valve Circuit Open

    Same failure as SPN 651 FMI 5 ("Injector Cylinder #1 Needle Control Valve Circuit Open") on a sibling part: Detroit lists SPN 652 FMI 5 as "Injector Cylinder #2 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 652 FMI 6Injector Cylinder #2 Needle Control Valve Shorted Circuit

    Same failure as SPN 651 FMI 6 ("Injector Cylinder #1 Needle Control Valve Shorted Circuit") on a sibling part: Detroit lists SPN 652 FMI 6 as "Injector Cylinder #2 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 6, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 6, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 653 FMI 3Injector Cylinder #3 Needle Control Valve Abnormal Operation (MAX)

    Same failure as SPN 651 FMI 3 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)") on a sibling part: Detroit lists SPN 653 FMI 3 as "Injector Cylinder #3 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 653 FMI 4Injector Cylinder #3 Needle Control Valve Abnormal Operation (MIN)

    Same failure as SPN 651 FMI 4 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)") on a sibling part: Detroit lists SPN 653 FMI 4 as "Injector Cylinder #3 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 653 FMI 5Injector Cylinder #3 Needle Control Valve Circuit Open

    Same failure as SPN 651 FMI 5 ("Injector Cylinder #1 Needle Control Valve Circuit Open") on a sibling part: Detroit lists SPN 653 FMI 5 as "Injector Cylinder #3 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 653 FMI 6Injector Cylinder #3 Needle Control Valve Shorted Circuit

    Same failure as SPN 651 FMI 6 ("Injector Cylinder #1 Needle Control Valve Shorted Circuit") on a sibling part: Detroit lists SPN 653 FMI 6 as "Injector Cylinder #3 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 6, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 6, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 654 FMI 3Injector Cylinder #4 Needle Control Valve Abnormal Operation (MAX)

    Same failure as SPN 651 FMI 3 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)") on a sibling part: Detroit lists SPN 654 FMI 3 as "Injector Cylinder #4 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 654 FMI 4Injector Cylinder #4 Needle Control Valve Abnormal Operation (MIN)

    Same failure as SPN 651 FMI 4 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)") on a sibling part: Detroit lists SPN 654 FMI 4 as "Injector Cylinder #4 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 654 FMI 5Injector Cylinder #4 Needle Control Valve Circuit Open

    Same failure as SPN 651 FMI 5 ("Injector Cylinder #1 Needle Control Valve Circuit Open") on a sibling part: Detroit lists SPN 654 FMI 5 as "Injector Cylinder #4 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 654 FMI 6Injector Cylinder #4 Needle Control Valve Shorted Circuit

    Same failure as SPN 651 FMI 6 ("Injector Cylinder #1 Needle Control Valve Shorted Circuit") on a sibling part: Detroit lists SPN 654 FMI 6 as "Injector Cylinder #4 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 6, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 6, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 655 FMI 3Injector Cylinder #5 Needle Control Valve Abnormal Operation (MAX)

    Same failure as SPN 651 FMI 3 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)") on a sibling part: Detroit lists SPN 655 FMI 3 as "Injector Cylinder #5 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 655 FMI 4Injector Cylinder #5 Needle Control Valve Abnormal Operation (MIN)

    Same failure as SPN 651 FMI 4 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)") on a sibling part: Detroit lists SPN 655 FMI 4 as "Injector Cylinder #5 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 655 FMI 5Injector Cylinder #5 Needle Control Valve Circuit Open

    Same failure as SPN 651 FMI 5 ("Injector Cylinder #1 Needle Control Valve Circuit Open") on a sibling part: Detroit lists SPN 655 FMI 5 as "Injector Cylinder #5 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 655 FMI 6Injector Cylinder #5 Needle Control Valve Shorted Circuit

    Same failure as SPN 651 FMI 6 ("Injector Cylinder #1 Needle Control Valve Shorted Circuit") on a sibling part: Detroit lists SPN 655 FMI 6 as "Injector Cylinder #5 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 6, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 6, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 656 FMI 3Injector Cylinder #6 Needle Control Valve Abnormal Operation (MAX)

    Same failure as SPN 651 FMI 3 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX)") on a sibling part: Detroit lists SPN 656 FMI 3 as "Injector Cylinder #6 Needle Control Valve Abnormal Operation (MAX)".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 656 FMI 4Injector Cylinder #6 Needle Control Valve Abnormal Operation (MIN)

    Same failure as SPN 651 FMI 4 ("Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN)") on a sibling part: Detroit lists SPN 656 FMI 4 as "Injector Cylinder #6 Needle Control Valve Abnormal Operation (MIN)".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 656 FMI 5Injector Cylinder #6 Needle Control Valve Circuit Open

    Same failure as SPN 651 FMI 5 ("Injector Cylinder #1 Needle Control Valve Circuit Open") on a sibling part: Detroit lists SPN 656 FMI 5 as "Injector Cylinder #6 Needle Control Valve Circuit Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 656 FMI 6Injector Cylinder #6 Needle Control Valve Shorted Circuit

    Same failure as SPN 651 FMI 6 ("Injector Cylinder #1 Needle Control Valve Shorted Circuit") on a sibling part: Detroit lists SPN 656 FMI 6 as "Injector Cylinder #6 Needle Control Valve Shorted Circuit".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 651 FMI 6, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 651 FMI 6, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 2797 FMI 3Fuel Injector Needle Control Valve for Cylinder 1, 2, 3 Shorted to Battery Power

    Detroit lists SPN 2797 FMI 3 as "Fuel Injector Needle Control Valve for Cylinder 1, 2, 3 Shorted to Battery Power".· Shorted high
    Check soon

    Causes

    • A partial short inside the needle valve coil or in the injector connector pulling extra current
    • Wire insulation damaged so the circuit leaks to another wire

    Checks

    1. 1Measure the needle valve coil resistance at the harness connector and compare it with the other cylinders; a low value points to a shorted coil.
    2. 2Look for a damaged section of the valve cover harness where two injector wires touch.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 2797 FMI 4Fuel Injector Needle Control Valve Cylinder 1, 2, 3 Shorted to Ground

    Detroit lists SPN 2797 FMI 4 as "Fuel Injector Needle Control Valve Cylinder 1, 2, 3 Shorted to Ground".· Shorted low
    Check soon

    Causes

    • High resistance in the needle valve circuit from a corroded pin or a half-broken wire
    • Weak or sticking solenoid in the injector

    Checks

    1. 1Check the needle valve connector pins for corrosion and spread terminals, then measure the circuit resistance end to end.
    2. 2Compare the value against a cylinder that has no code to see how far this one is out.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 2798 FMI 3Injector Needle Control Valve Cylinder 4, 5, 6 shorted to Battery

    Same failure as SPN 2797 FMI 3 ("Fuel Injector Needle Control Valve for Cylinder 1, 2, 3 Shorted to Battery Power") on a sibling part: Detroit lists SPN 2798 FMI 3 as "Injector Needle Control Valve Cylinder 4, 5, 6 shorted to Battery".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 2797 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 2797 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 2798 FMI 4Injector Needle Control Valve Cylinder 4, 5, 6 Shorted to Ground

    Same failure as SPN 2797 FMI 4 ("Fuel Injector Needle Control Valve Cylinder 1, 2, 3 Shorted to Ground") on a sibling part: Detroit lists SPN 2798 FMI 4 as "Injector Needle Control Valve Cylinder 4, 5, 6 Shorted to Ground".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 2797 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 2797 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Read the code with the cylinder number and check whether the same cylinder also logs a misfire or an amplifier valve code.
  2. 2Inspect the injector connector under the valve cover and the harness pass-through for oil, chafing and heat damage.
  3. 3Measure the injector solenoid resistance at the harness connector and compare it with the other cylinders.
  4. 4Check the injector circuit for a short to battery or ground with the harness unplugged from the MCM.
  5. 5Replace the injector or harness section that fails, then clear the code and verify with an injector test.

Causes

  • Injector solenoid or internal wiring failure
  • Injector connector or valve cover harness damaged, wet or chafed
  • Wire short between two injector circuits
  • MCM injector driver fault

Most common here: shorted low (14 of 28)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: Rough running, a misfire on the named cylinder, a loss of power and the check-engine or stop-engine lamp; some cases derate.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.