Detroit · Injectors
Detroit Cylinder misfire and injection mode fault codes
The MCM tracks how steadily each cylinder contributes to engine speed and flags misfire rates above 5 percent per cylinder or across several cylinders. It also reports the symmetric and asymmetric injection modes Detroit uses for cold starting and half-engine operation.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 1322 FMI 9 to SPN 521174 FMI 31 are all about the cylinder misfire and injection mode. The most common failure type is erratic or implausible (8 of 22); none needs an immediate stop. Start with this check: read the live misfire counts or run the cylinder cut-out test in the diagnostic tool to find the weak cylinder.
How urgent are they?
None of the 22 codes here means stop now; all 22 can wait until the shift ends, but find the cause before the next one.
- Check soon22
What should I check first?
Read the live misfire counts or run the cylinder cut-out test in the diagnostic tool to find the weak cylinder.
Shared checks22 of 22
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 1322 FMI 9Misfire on Alternating Cylinders Detected
Detroit lists SPN 1322 FMI 9 as "Misfire on Alternating Cylinders Detected". The MCM logged this condition for the cylinder; the title says what it measured. Misfire detection compares the acceleration of each cylinder; this entry covers misfire on several cylinders or on alternating cylinders at once.· Lost messageLost messageCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3The imbalance alternates between cylinders, so check for a shared cause such as rail pressure or a common injector supply.
- 4Alternating misfire often follows a bank-wide cause, so compare the rail pressure and the injector supply voltage on both banks before pulling an injector.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 1322 FMI 10Simultaneous Asymmetry Mode Misfire on Multiple Cylinders Detected
Detroit lists SPN 1322 FMI 10 as "Simultaneous Asymmetry Mode Misfire on Multiple Cylinders Detected". The MCM measured a misfire rate above 5 percent on this cylinder, or an asymmetry across cylinders. Misfire detection compares the acceleration of each cylinder; this entry covers misfire on several cylinders or on alternating cylinders at once.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Injector failing on this cylinder
- Low compression on this cylinder
Checks
- 1Run the cylinder cut-out test and note the drop for this cylinder.
- 2Check compression or leak-down on the cylinder if the injector tests good.
- 3Misfire in asymmetric mode on several cylinders at once points to a shared cause such as fuel supply, air or a software mode problem.
- 4Because the engine runs several cylinders in asymmetry mode here, read which cylinders are listed in the freeze frame and test those injectors together.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1322 FMI 11Asymmetry Mode Misfire on Alternating Cylinders Detected
Detroit lists SPN 1322 FMI 11 as "Asymmetry Mode Misfire on Alternating Cylinders Detected". The MCM measured a misfire rate above 5 percent in the asymmetry mode, where the cylinders are fired differently for cold running. Misfire detection compares the acceleration of each cylinder; this entry covers misfire on several cylinders or on alternating cylinders at once.· OtherOtherCheck soonCauses
- Injector failing on this cylinder
- Cold-start injection mode not completing
Checks
- 1Check whether the code returns only on a cold start.
- 2Run the cylinder cut-out test when the engine is warm.
- 3Check whether the misfire only occurs during cold running, when the engine uses the asymmetric injection mode.
- 4Warm the engine fully and recheck; if the misfire disappears warm, the cold asymmetry pattern and its temperature inputs are the place to look.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 1322 FMI 12Simultaneous Misfire on Multiple Cylinders Detected
Detroit lists SPN 1322 FMI 12 as "Simultaneous Misfire on Multiple Cylinders Detected". The MCM logged this condition for the cylinder; the title says what it measured. Misfire detection compares the acceleration of each cylinder; this entry covers misfire on several cylinders or on alternating cylinders at once.· Part or controllerPart or controllerCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3Several cylinders misfiring at once points to supply: fuel quality, filters, air in the fuel or rail pressure.
- 4Simultaneous misfire on several cylinders almost always means fuel or air supply, so test the lift pump pressure and the air path first.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 1323 FMI 10Cylinder #1 Misfire Rate Above 5% Detected
Detroit lists SPN 1323 FMI 10 as "Cylinder #1 Misfire Rate Above 5% Detected". The MCM measured a misfire rate above 5 percent on this cylinder, or an asymmetry across cylinders. It is the cylinder 1 entry. Misfire on cylinder 1 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Injector failing on this cylinder
- Low compression on this cylinder
Checks
- 1Run the cylinder cut-out test and note the drop for this cylinder.
- 2Check compression or leak-down on the cylinder if the injector tests good.
- 3Run the cylinder cut-out test for cylinder 1 and check its injector trim code and connector first.
- 4Cylinder 1 sits at the end of the engine where the harness enters, so check the connector there for oil and strain before replacing the injector.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1324 FMI 10Cylinder #2 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1324 FMI 10 as "Cylinder #2 Misfire Rate Above 5% Detected". Misfire on cylinder 2 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1325 FMI 10Cylinder #3 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1325 FMI 10 as "Cylinder #3 Misfire Rate Above 5% Detected". Misfire on cylinder 3 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1326 FMI 10Cylinder #4 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1326 FMI 10 as "Cylinder #4 Misfire Rate Above 5% Detected". Misfire on cylinder 4 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1326 FMI 11Cylinder #4 Asymmetry Mode Misfire Rate Above 5% Detected
Detroit lists SPN 1326 FMI 11 as "Cylinder #4 Asymmetry Mode Misfire Rate Above 5% Detected". The MCM measured a misfire rate above 5 percent in the asymmetry mode, where the cylinders are fired differently for cold running. It is the cylinder 4 entry. Misfire on cylinder 4 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· OtherOtherCheck soonCauses
- Injector failing on this cylinder
- Cold-start injection mode not completing
Checks
- 1Check whether the code returns only on a cold start.
- 2Run the cylinder cut-out test when the engine is warm.
- 3Check cylinder 4 in the cold-start asymmetry mode and see whether the code returns only when the engine is cold.
- 4Cylinder 4 asymmetry misfire in the cold pattern: confirm the coolant and intake temperature signals are believable, because they select the mode.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 1327 FMI 10Cylinder #5 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1327 FMI 10 as "Cylinder #5 Misfire Rate Above 5% Detected". Misfire on cylinder 5 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1327 FMI 11Cylinder #5 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1327 FMI 11 as "Cylinder #5 Misfire Rate Above 5% Detected". Misfire on cylinder 5 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· OtherOtherCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 1328 FMI 10Cylinder #6 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1328 FMI 10 as "Cylinder #6 Misfire Rate Above 5% Detected". Misfire on cylinder 6 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1328 FMI 11Cylinder #6 Misfire Rate Above 5% Detected
Same failure as SPN 1323 FMI 10 ("Cylinder #1 Misfire Rate Above 5% Detected") on a sibling part: Detroit lists SPN 1328 FMI 11 as "Cylinder #6 Misfire Rate Above 5% Detected". Misfire on cylinder 6 is flagged when its share of engine acceleration falls clearly below the others over a counted number of cycles.· OtherOtherCheck soonCauses
- The causes listed under SPN 1323 FMI 10, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1323 FMI 10, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 3061 FMI 1Cold Start Emission Reduction Strategy Fault Condition for POI Main
Detroit lists SPN 3061 FMI 1 as "Cold Start Emission Reduction Strategy Fault Condition for POI Main". The MCM logged this condition for the cylinder; the title says what it measured. The cold start emission strategy changes the injection pattern while the engine is cold; faults point to the main injection, the EGR position or the asymmetric injection.· Real conditionReal conditionCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3The cold start strategy fault for the main injection; check the cold-start injection logic, rail pressure and injectors.
- 4The main injection point of injection (POI) is wrong in the cold strategy, so verify the rail pressure at cold start and the injector timing trims.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3061 FMI 2Cold Start Emission Reduction Strategy Fault Condition EGR Position
Detroit lists SPN 3061 FMI 2 as "Cold Start Emission Reduction Strategy Fault Condition EGR Position". The MCM logged this condition for the cylinder; the title says what it measured. The cold start emission strategy changes the injection pattern while the engine is cold; faults point to the main injection, the EGR position or the asymmetric injection.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3The cold start strategy fault for the EGR position; check the EGR valve position control when cold.
- 4The cold strategy wants the EGR valve in a set position; command it in the tool when cold and compare the feedback.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3061 FMI 9Cold Start Emission Reduction Asymmetric Injection Failure
Detroit lists SPN 3061 FMI 9 as "Cold Start Emission Reduction Asymmetric Injection Failure". The MCM logged this condition for the cylinder; the title says what it measured. The cold start emission strategy changes the injection pattern while the engine is cold; faults point to the main injection, the EGR position or the asymmetric injection.· Lost messageLost messageCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3The cold start asymmetric injection failed; check the injectors and the cold-start strategy for the cylinder group.
- 4The asymmetric cold injection was not carried out; check that no injector or rail pressure code blocks the asymmetric pattern.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 521012 FMI 1Intake Deviation Low
Detroit lists SPN 521012 FMI 1 as "Intake Deviation Low". The MCM logged this condition for the cylinder; the title says what it measured. Intake deviation low means measured air is lower than modelled.· Real conditionReal conditionCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3The intake air is lower than the model; check the filter, the piping and the turbo.
- 4Compare the intake manifold pressure and the air flow model; a low deviation often comes from a restricted filter, a leak or a turbo that is not building boost.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521013 FMI 31Symmetric Injection Mode Expected
Detroit lists SPN 521013 FMI 31 as "Symmetric Injection Mode Expected". The MCM reports that an injection mode was expected but was not performed, or performed without being requested. A symmetric injection mode was expected but not used.· Real conditionReal conditionCheck soonCauses
- Mode selection logic upset by a sensor or software fault
- Related temperature or position sensor fault
Checks
- 1Read the codes stored with it for a temperature or EGR fault.
- 2Check the software release for the MCM.
- 3A symmetric injection mode was expected; check the cold-start logic and the temperature inputs.
- 4The MCM expected equal injection on all cylinders; look for a temperature signal that wrongly selects asymmetry and for injector codes.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521014 FMI 14Asymmetric Injection Mode Expected, Cold Condition
Detroit lists SPN 521014 FMI 14 as "Asymmetric Injection Mode Expected, Cold Condition". The MCM logged this condition for the cylinder; the title says what it measured. An asymmetric injection mode was expected (cold or normal) but not used.· OtherOtherCheck soonCauses
- The system under test has a real mechanical or fuelling fault
- A parameter, trim or calibration is missing or wrong
Checks
- 1Read the live data around the code and compare it with the other cylinders.
- 2Confirm the calibration and trim data are loaded.
- 3An asymmetric injection mode was expected when cold; check the temperature inputs and the strategy.
- 4Cold asymmetric mode was expected but did not occur; check the coolant temperature signal and the intake temperature before suspecting the injectors.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 521014 FMI 31Asymmetric Injection Mode Expected
Detroit lists SPN 521014 FMI 31 as "Asymmetric Injection Mode Expected". The MCM reports that an injection mode was expected but was not performed, or performed without being requested. An asymmetric injection mode was expected (cold or normal) but not used.· Real conditionReal conditionCheck soonCauses
- Mode selection logic upset by a sensor or software fault
- Related temperature or position sensor fault
Checks
- 1Read the codes stored with it for a temperature or EGR fault.
- 2Check the software release for the MCM.
- 3An asymmetric injection mode was expected; check the temperature inputs and the strategy.
- 4Asymmetric mode was expected but not run; look at the half-engine and cold-start codes stored with it.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521099 FMI 31Exhaust Gas Smart Remote Actuator 3 (EGR) Position Deviation Cold Condition
Detroit lists SPN 521099 FMI 31 as "Exhaust Gas Smart Remote Actuator 3 (EGR) Position Deviation Cold Condition". The MCM reports that an injection mode was expected but was not performed, or performed without being requested. The EGR actuator position deviates when cold.· Real conditionReal conditionCheck soonCauses
- Mode selection logic upset by a sensor or software fault
- Related temperature or position sensor fault
Checks
- 1Read the codes stored with it for a temperature or EGR fault.
- 2Check the software release for the MCM.
- 3The EGR position deviates when cold; check the valve for sticking in cold conditions.
- 4The EGR valve position is off when cold; check whether the valve sticks only until it warms up, which points to carbon.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521174 FMI 31Half Engine Operation Mode is Performed but Not Requested
Detroit lists SPN 521174 FMI 31 as "Half Engine Operation Mode is Performed but Not Requested". The MCM reports that an injection mode was expected but was not performed, or performed without being requested. Half engine operation mode is performed but not requested.· Real conditionReal conditionCheck soonCauses
- Mode selection logic upset by a sensor or software fault
- Related temperature or position sensor fault
Checks
- 1Read the codes stored with it for a temperature or EGR fault.
- 2Check the software release for the MCM.
- 3Half engine mode was performed without a request; check the strategy and the injector codes.
- 4The engine ran in half-engine mode without a request; check for cylinder codes and for software that triggers the mode wrongly.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Read the live misfire counts or run the cylinder cut-out test in the diagnostic tool to find the weak cylinder.
- 2Check that the injector trim codes are loaded in the MCM for any injector that was replaced.
- 3Check the rail pressure and the low-pressure supply while the engine misfires.
- 4Perform a compression or leak-down check on the cylinder that stays on the list.
- 5Inspect the injector connector and harness for the same cylinder before condemning the injector.
Causes
- Worn, leaking or sticking injector on the named cylinder
- Low compression or a valve problem on that cylinder
- Injector trim codes missing or wrong after a service
- Air or water in the fuel, or low rail pressure
Most common here: erratic or implausible (8 of 22)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: Rough running, white smoke on a cold start, a power loss and the check-engine lamp.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
