Detroit · Injectors
Detroit Cold-start injector current checks fault codes
Detroit repeats the needle control valve checks for each cylinder as cold-engine tests (SPN 7384 to 7389). They run when the engine is cold and compare the valve current against the abnormal-operation limits for that condition.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 7384 FMI 3 to SPN 7389 FMI 4 are all about the cold-start injector current checks. The most common failure type is shorted high (6 of 12); none needs an immediate stop. Start with this check: note whether the code returns only on a cold start and clear it after the engine has warmed.
How urgent are they?
None of the 12 codes here means stop now; all 12 can wait until the shift ends, but find the cause before the next one.
- Check soon12
What should I check first?
Note whether the code returns only on a cold start and clear it after the engine has warmed.
Shared checks12 of 12
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 7384 FMI 3Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold
Detroit lists SPN 7384 FMI 3 as "Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold". The MCM saw the injector needle control valve drawing more current than its upper limit during an injection pulse, which Detroit calls the MAX abnormal-operation limit. This version of the test is run while the engine is cold. It is the cylinder 1 entry. The cold version of the cylinder 1 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- A partial short inside the cold needle valve coil or in the injector connector pulling extra current
- Wire insulation damaged so the circuit leaks to another wire
Checks
- 1Measure the cold needle valve coil resistance at the harness connector and compare it with the other cylinders; a low value points to a shorted coil.
- 2Look for a damaged section of the valve cover harness where two injector wires touch.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7384 FMI 4Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold
Detroit lists SPN 7384 FMI 4 as "Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold". The MCM saw the injector needle control valve drawing less current than its lower limit during an injection pulse, which Detroit calls the MIN abnormal-operation limit. This version of the test is run while the engine is cold. It is the cylinder 1 entry. The cold version of the cylinder 1 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- High resistance in the cold needle valve circuit from a corroded pin or a half-broken wire
- Weak or sticking solenoid in the injector
Checks
- 1Check the cold needle valve connector pins for corrosion and spread terminals, then measure the circuit resistance end to end.
- 2Compare the value against a cylinder that has no code to see how far this one is out.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 7385 FMI 3Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MAX) Cold
Same failure as SPN 7384 FMI 3 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold") on a sibling part: Detroit lists SPN 7385 FMI 3 as "Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MAX) Cold". The cold version of the cylinder 2 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 7384 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7385 FMI 4Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MIN) Cold
Same failure as SPN 7384 FMI 4 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold") on a sibling part: Detroit lists SPN 7385 FMI 4 as "Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MIN) Cold". The cold version of the cylinder 2 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 7384 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 7386 FMI 3Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MAX) Cold
Same failure as SPN 7384 FMI 3 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold") on a sibling part: Detroit lists SPN 7386 FMI 3 as "Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MAX) Cold". The cold version of the cylinder 3 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 7384 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7386 FMI 4Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MIN) Cold
Same failure as SPN 7384 FMI 4 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold") on a sibling part: Detroit lists SPN 7386 FMI 4 as "Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MIN) Cold". The cold version of the cylinder 3 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 7384 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 7387 FMI 3Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MAX) Cold
Same failure as SPN 7384 FMI 3 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold") on a sibling part: Detroit lists SPN 7387 FMI 3 as "Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MAX) Cold". The cold version of the cylinder 4 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 7384 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7387 FMI 4Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MIN) Cold
Same failure as SPN 7384 FMI 4 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold") on a sibling part: Detroit lists SPN 7387 FMI 4 as "Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MIN) Cold". The cold version of the cylinder 4 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 7384 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 7388 FMI 3Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MAX) Cold
Same failure as SPN 7384 FMI 3 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold") on a sibling part: Detroit lists SPN 7388 FMI 3 as "Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MAX) Cold". The cold version of the cylinder 5 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 7384 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7388 FMI 4Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MIN) Cold
Same failure as SPN 7384 FMI 4 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold") on a sibling part: Detroit lists SPN 7388 FMI 4 as "Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MIN) Cold". The cold version of the cylinder 5 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 7384 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 7389 FMI 3Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MAX) Cold
Same failure as SPN 7384 FMI 3 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) Cold") on a sibling part: Detroit lists SPN 7389 FMI 3 as "Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MAX) Cold". The cold version of the cylinder 6 needle control valve check runs while the engine is cold.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 7384 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 7389 FMI 4Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MIN) Cold
Same failure as SPN 7384 FMI 4 ("Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) Cold") on a sibling part: Detroit lists SPN 7389 FMI 4 as "Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MIN) Cold". The cold version of the cylinder 6 needle control valve check runs while the engine is cold.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 7384 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 7384 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Note whether the code returns only on a cold start and clear it after the engine has warmed.
- 2Inspect the valve cover harness and injector connector for moisture and corrosion.
- 3Check the battery and the cold fuel supply before replacing an injector.
- 4Run an injector test in the tool when the engine is cold and again when warm.
Causes
- Injector needle valve sticking while cold
- Wet or corroded injector connector
- Cold weather pushing a marginal solenoid out of range
- Thick fuel or a weak battery in cold conditions
Most common here: shorted high (6 of 12)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: A cold-start misfire, white smoke or rough running that clears as the engine warms, with a check-engine lamp.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
