EF Logo

Detroit · Air system

Detroit Charge air, intake manifold and ambient temperature fault codes

These sensors watch the compressor inlet, the charge air cooler outlet, the intake manifold and the ambient air. The MCM uses them to protect the engine and to judge the cooler efficiency.

FaultCheckSPN 171FMI 2Detroit · Charge air, intake manifold and ambient temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 171 FMI 2 to SPN 5125 FMI 14 are all about the charge air, intake manifold and ambient temperature. The most common failure type is erratic or implausible (9 of 24); none needs an immediate stop. Start with this check: compare the tool reading of each temperature with a surface thermometer on a cold engine.

How urgent are they?

None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.

  • Check soon24

What should I check first?

Compare the tool reading of each temperature with a surface thermometer on a cold engine.

Shared checks

24 of 24

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 171 FMI 2Ambient Air Temperature Sensor, General Temperature Plausibility Error

    Detroit lists SPN 171 FMI 2 as "Ambient Air Temperature Sensor, General Temperature Plausibility Error".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting intake temperature sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 171 FMI 3Ambient Temperature Sensor Failed High or Open

    Detroit lists SPN 171 FMI 3 as "Ambient Temperature Sensor Failed High or Open".· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V supply or open between the intake temperature sensor and the MCM
    • The intake temperature sensor has failed inside

    Checks

    1. 1Unplug the intake temperature sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
    2. 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 171 FMI 4Ambient Temperature Sensor Failed Low

    Detroit lists SPN 171 FMI 4 as "Ambient Temperature Sensor Failed Low".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The intake temperature sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the intake temperature sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 171 FMI 13Ambient Air Temperature Signal Not Available via the Controller Area Network

    Detroit lists SPN 171 FMI 13 as "Ambient Air Temperature Signal Not Available via the Controller Area Network".· Part or controller
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the intake temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the intake temperature sensor for leaks, restrictions or contamination.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 171 FMI 19Ambient Air Temperature Signal Error

    Detroit lists SPN 171 FMI 19 as "Ambient Air Temperature Signal Error".· Lost message
    Check soon

    Causes

    • Signal path broken at the connector or the harness
    • Failed sensor or module

    Checks

    1. 1Check the connector and the power supply to the intake temperature sensor.
    2. 2Check the signal wire to the MCM for an open.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 171 FMI 20Ambient Temperature Sensor Signal Not Plausible

    Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 171 FMI 20 as "Ambient Temperature Sensor Signal Not Plausible".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1172 FMI 3Turbocharger Compressor Inlet Temperature Sensor or Circuit Failed High

    Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 1172 FMI 3 as "Turbocharger Compressor Inlet Temperature Sensor or Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 1172 FMI 4Turbocharger Compressor Inlet Temperature Circuit Failed Low

    Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 1172 FMI 4 as "Turbocharger Compressor Inlet Temperature Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 1172 FMI 14Turbocharger Compressor Inlet Temperature Sensor Drift in Range

    Detroit lists SPN 1172 FMI 14 as "Turbocharger Compressor Inlet Temperature Sensor Drift in Range".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting intake temperature sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1172 FMI 21Compressor Inlet Temperature Sensor Signal Not Plausible

    Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 1172 FMI 21 as "Compressor Inlet Temperature Sensor Signal Not Plausible".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1636 FMI 0Charge Air Cooler Low Efficiency

    Detroit lists SPN 1636 FMI 0 as "Charge Air Cooler Low Efficiency".· Real condition
    Check soon

    Causes

    • A real fault in the system the intake temperature sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the intake temperature sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 1636 FMI 3Intake Manifold Temperature Circuit Failed High

    Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 1636 FMI 3 as "Intake Manifold Temperature Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 1636 FMI 4Intake Manifold Temperature Circuit Failed Low

    Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 1636 FMI 4 as "Intake Manifold Temperature Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 1636 FMI 10Intake Manifold Temperature - Signal Spike

    Detroit lists SPN 1636 FMI 10 as "Intake Manifold Temperature - Signal Spike".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting intake temperature sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1636 FMI 14Intake Manifold Temperature Sensor Signal Not Plausible

    Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 1636 FMI 14 as "Intake Manifold Temperature Sensor Signal Not Plausible".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1636 FMI 16Charge Air Cooler Efficiency Low

    Detroit lists SPN 1636 FMI 16 as "Charge Air Cooler Efficiency Low".· Real condition
    Check soon

    Causes

    • A real fault in the system the intake temperature sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the intake temperature sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 1636 FMI 21Intake Manifold Temperature Drift-High Box

    Detroit lists SPN 1636 FMI 21 as "Intake Manifold Temperature Drift-High Box".· Erratic or implausible
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the intake temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the intake temperature sensor for leaks, restrictions or contamination.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1636 FMI 31Intake Manifold Temperature Sensor Drift in Range

    Same failure as SPN 1172 FMI 14 ("Turbocharger Compressor Inlet Temperature Sensor Drift in Range") on a sibling part: Detroit lists SPN 1636 FMI 31 as "Intake Manifold Temperature Sensor Drift in Range".· Real condition
    Check soon

    Causes

    • The causes listed under SPN 1172 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1172 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 2630 FMI 3Charge Air Cooler Outlet Temperature Circuit Failed High

    Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 2630 FMI 3 as "Charge Air Cooler Outlet Temperature Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 2630 FMI 4Intake Air Temperature Circuit Failed Low

    Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 2630 FMI 4 as "Intake Air Temperature Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 2630 FMI 14Charge Air Cooler Outlet Sensor Signal Not Plausible

    Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 2630 FMI 14 as "Charge Air Cooler Outlet Sensor Signal Not Plausible".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 5125 FMI 3Ambient Temperature Sensor Failed High or Open

    Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 5125 FMI 3 as "Ambient Temperature Sensor Failed High or Open".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 5125 FMI 4Ambient Temperature Sensor Failed High or Open

    Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 5125 FMI 4 as "Ambient Temperature Sensor Failed High or Open".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 5125 FMI 14CPC5 Overtemp - Pin X3_35

    Detroit lists SPN 5125 FMI 14 as "CPC5 Overtemp - Pin X3_35".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting intake temperature sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

Shared checks

Checks, in order

  1. 1Compare the tool reading of each temperature with a surface thermometer on a cold engine.
  2. 2Inspect the sensor connectors for oil and corrosion and check the harness for chafing.
  3. 3Pressure-test the charge air system and the cooler for leaks.
  4. 4Check the radiator and cooler fins for debris and blocked airflow.
  5. 5Replace the sensor only when the wiring and cooler tests are good.

Causes

  • Charge air cooler leak, plugged fins or restricted airflow
  • Sensor connector damage or wiring short
  • Contaminated or drifted sensor
  • Cooling air blocked or an ambient sensor mounted in a hot spot

Most common here: erratic or implausible (9 of 24)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: A loss of power, black smoke or poor cold-start behaviour, and the check-engine lamp.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.