Detroit · Air system
Detroit Boost pressure, ambient pressure and turbocharger fault codes
The MCM uses the intake manifold (boost) pressure sensor, the barometric pressure sensor and the turbocharger speed signal to control fuelling. Detroit logs circuit faults, drift between the two pressure sensors, and real over-boost or low air flow.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 103 FMI 0 to SPN 3563 FMI 21 are all about the boost pressure, ambient pressure and turbocharger. The most common failure type is erratic or implausible (5 of 15); none needs an immediate stop. Start with this check: check the air filter restriction indicator and the intake piping for leaks and cracked clamps.
How urgent are they?
None of the 15 codes here means stop now; all 15 can wait until the shift ends, but find the cause before the next one.
- Check soon15
What should I check first?
Check the air filter restriction indicator and the intake piping for leaks and cracked clamps.
Shared checks15 of 15
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 103 FMI 0Turbocharger Speed Below Threshold - Low Box
Detroit lists SPN 103 FMI 0 as "Turbocharger Speed Below Threshold - Low Box". The MCM reports that the measured value itself is out of its normal range; the pressure sensor may be correct and a real condition may exist. Turbocharger speed is derived from a speed sensor at the compressor housing and is used to stop the turbine from overspeeding.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 103 FMI 1Turbocharger Speed Below Threshold - High Box
Detroit lists SPN 103 FMI 1 as "Turbocharger Speed Below Threshold - High Box". The MCM reports that the measured value itself is out of its normal range; the pressure sensor may be correct and a real condition may exist. Turbocharger speed is derived from a speed sensor at the compressor housing and is used to stop the turbine from overspeeding.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 103 FMI 2Turbocharger Speed Not Plausible
Detroit lists SPN 103 FMI 2 as "Turbocharger Speed Not Plausible". The MCM judged the pressure sensor reading erratic or not plausible compared with other sensors or its own history. Turbocharger speed is derived from a speed sensor at the compressor housing and is used to stop the turbine from overspeeding.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 108 FMI 2Sensor Drift Fault for Ambient Air Pressure
Detroit lists SPN 108 FMI 2 as "Sensor Drift Fault for Ambient Air Pressure". The MCM judged the pressure sensor reading erratic or not plausible compared with other sensors or its own history. The barometric pressure value corrects fuelling and boost for altitude; it is read at key-on from the ambient sensor or received on the CAN.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 108 FMI 3Barometric Pressure (BP) Sensor Circuit Failed High
Detroit lists SPN 108 FMI 3 as "Barometric Pressure (BP) Sensor Circuit Failed High". The MCM saw the pressure sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The barometric pressure value corrects fuelling and boost for altitude; it is read at key-on from the ambient sensor or received on the CAN.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the pressure sensor and the MCM
- The pressure sensor has failed inside
Checks
- 1Unplug the pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 108 FMI 4Barometric Pressure (BP) Sensor Circuit Failed Low
Detroit lists SPN 108 FMI 4 as "Barometric Pressure (BP) Sensor Circuit Failed Low". The MCM saw the pressure sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The barometric pressure value corrects fuelling and boost for altitude; it is read at key-on from the ambient sensor or received on the CAN.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The pressure sensor has failed inside or its supply wire is open
Checks
- 1Unplug the pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 108 FMI 13Ambient Air Pressure Signal Not Available via CAN
Detroit lists SPN 108 FMI 13 as "Ambient Air Pressure Signal Not Available via CAN". The MCM found the pressure sensor value drifted away from what the engine state says it should be. The barometric pressure value corrects fuelling and boost for altitude; it is read at key-on from the ambient sensor or received on the CAN.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the pressure sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 2631 FMI 1Low Air Flow
Detroit lists SPN 2631 FMI 1 as "Low Air Flow". The MCM reports that the measured value itself is out of its normal range; the pressure sensor may be correct and a real condition may exist. Air flow is estimated from the intake pressure and temperature; low air flow often follows an air filter restriction or a leak.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3563 FMI 2Sensor Drift Fault for Charge Air Pressure
Same failure as SPN 108 FMI 2 ("Sensor Drift Fault for Ambient Air Pressure") on a sibling part: Detroit lists SPN 3563 FMI 2 as "Sensor Drift Fault for Charge Air Pressure". The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 108 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 108 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3563 FMI 3Intake Manifold Pressure Circuit Failed High
Same failure as SPN 108 FMI 3 ("Barometric Pressure (BP) Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 3563 FMI 3 as "Intake Manifold Pressure Circuit Failed High". The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 108 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 108 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3563 FMI 4Intake Manifold Pressure Circuit Failed Low
Same failure as SPN 108 FMI 4 ("Barometric Pressure (BP) Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 3563 FMI 4 as "Intake Manifold Pressure Circuit Failed Low". The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 108 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 108 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3563 FMI 10Barometric Pressure and Intake Manifold Pressure Rationality Error
Same failure as SPN 103 FMI 2 ("Turbocharger Speed Not Plausible") on a sibling part: Detroit lists SPN 3563 FMI 10 as "Barometric Pressure and Intake Manifold Pressure Rationality Error". The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 103 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 103 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3563 FMI 16Intake Manifold Pressure Too High
Detroit lists SPN 3563 FMI 16 as "Intake Manifold Pressure Too High". The MCM reports that the measured value itself is out of its normal range; the pressure sensor may be correct and a real condition may exist. The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3563 FMI 18Inlet Manifold Pressure Low
Detroit lists SPN 3563 FMI 18 as "Inlet Manifold Pressure Low". The MCM reports that the measured value itself is out of its normal range; the pressure sensor may be correct and a real condition may exist. The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3563 FMI 21Ambient and Inlet Manifold Pressure Difference (High Box)
Detroit lists SPN 3563 FMI 21 as "Ambient and Inlet Manifold Pressure Difference (High Box)". The MCM found the pressure sensor value drifted away from what the engine state says it should be. The intake manifold pressure sensor measures boost downstream of the charge air cooler and is the main input for fuelling.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the pressure sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Check the air filter restriction indicator and the intake piping for leaks and cracked clamps.
- 2Read boost and ambient pressure with the engine off; the two should agree.
- 3Inspect the sensor connector and the harness for chafing and corrosion.
- 4Check the turbocharger for shaft play and oil leaks into the intake.
- 5Test the boost circuit for shorts and replace the sensor only after the wiring checks good.
Causes
- Boost leak, restricted air filter or intake restriction
- Turbocharger or actuator fault
- Pressure sensor connector or wiring damage
- Pressure sensor drift or a plugged sensor port
Most common here: erratic or implausible (5 of 15)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A loss of power, turbo-related noise, black smoke and the check-engine lamp.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
